2021 HYUNDAI I20 instrument cluster

5-22
Instrument cluster
Low engine oil (if equipped)
This warning message is displayed when
the engine oil level should be checked.
If this warning message is displayed,
check the engine oil level as soon as
possible and add engine oil as required.
Slowly pour the recommended oil little
by little into a funnel.
Use only the specified engine oil. (Refer
to "Recommended lubricants and
capacities" section in chapter 2.)
Do not overfill the engine oil. Make sure
the oil level is not above F (Full) mark on
the dipstick.
NOTICE
If the message is displayed
continuously after adding the engine
oil and travelling approximately
50~100 km after the engine warms up,
we recommend that the system be
checked by an authorized HYUNDAI
dealer.
Engine has overheated
(if equipped)
This warning message is displayed
when the engine coolant temperature
is above 120°C (248°F). This means that
the engine is overheated and may be
damaged.
If your vehicle is overheated, refer to
“Overheating” section in chapter 8.
Check headlight (if equipped)
This warning message is displayed if the
headlamps are not operating properly.
In addition, if a specific lamp(turn signal
lamp etc.) is not operating properly, the
warning message according to a specific
lamp (turn signal lamp etc.) is displayed.
A corresponding bulb may need to be
replaced.
Make sure to replace the burned out
bulb with a new one of the same
wattage rating.
Check brake light (if equipped)
This warning message is displayed if the
stop lamps are not operating properly. A
lamp may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same
wattage rating.

5-24
Instrument cluster
LCD display modes
Modes Symbol Explanation
Trip
ComputerThis mode displays driving information such as the tripmeter,
fuel economy, etc.
For more details, refer to "Trip Computer" in this chapter.
Turn By
Turn (TBT)
This mode displays the state of the navigation.
Driving
Assist
- Cruise Control (CC)
- Tire Pressure (TPMS)
User
Settings
In this mode, you can change settings of the doors, lamps,
etc.
Warning
- This mode displays warning messages related to the
lamp malfunction, etc.
- Tire pressure information
The information provided may differ depending on which functions are applicable
to your vehicle.

5-26
Instrument cluster
Master warning
OBI3040018OBI3040018
This warning light informs the driver the
following situations.
- Tire Pressure Monitoring System
malfunction (if equipped)
The Master Warning Light illuminates
if one or more of the above warning
situations occur.
At this time, a Master Warning icon (
)
ill appear beside the User Settings icon
(
), on the LCD display.
If the warning situation is solved, the
master warning light will be turned
off and the Master Warning icon will
disappear.
User settings mode
In this mode, you can change the
settings of the instrument cluster, doors,
lamps, etc.
1. Door
2. Light
3. Convenience
4. Service Interval
5. Other
6. Language
7. Reset
The information provided may differ
depending on which functions are
applicable to your vehicle.
Shift to P to edit settings/Engage
parking brake to edit settings
This warning message illuminates if
you try to select an item from the User
Settings mode while driving.
• Automatic transmission / Intelligent
variable transmission
For your safety, change the User
Settings after parking the vehicle,
applying the parking brake and
moving the shift level to P(Park).
• Manual transmission
For your safety, change the User
Settings after engaging the parking
brake.
Quick guide (Help)
This mode provides quick guides for the
systems in the User Settings mode.
Select an item, press and hold the OK
button.
For more details about each system,
refer to this Owner’s Manual.

5-27
05
User settings mode
In this mode, you can change setting of the instrument cluster, doors, lamps, and so
on.
Door
ItemsExplanation
Auto Lock• Disable : The auto door lock operation will be deactivated.
• Enable on Speed : All doors will be automatically locked when the
vehicle speed exceeds 9.3 mph (15km/h).
• Enable on Shift : All doors will be automatically locked if the dual
clutch transmission shift lever is shifted from the P (Park) position
to the R (Reverse), N (Neutral), or D (Drive) position. (Only when the
engine is running.)
Auto Unlock• Disable : The auto door unlock operation will be canceled.
• Vehicle Off: All doors will be automatically unlocked when the ignition
key is removed from the ignition switch or the Engine Star/Stop button
is set to the OFF position.
• On Shift to P: All doors will be automatically unlocked if the dual clutch
transmission shift lever is shifted to the P (Park) position. (Only when
the engine is running.)
Light
ItemsExplanation
IlluminationTo adjust the brightness of the instrument panel illumination.
One Touch Turn
Signal• Off: The one touch turn signal function will be deactivated.
• 3, 5, 7 Flashes : The lane change signals will blink 3, 5, or 7 times when
the turn signal lever is moved slightly.
For more details, refer to “Light” in chapter 5.
Ambient light
brightness• Off/Level 1/Level 2/Level 3/Level 4
To adjust the brightness of the Ambient Light (cabin mood light setting).
Ambient LightTo activate or deactivate the Ambient Light (cabin mood light setting)
function.
Head Lamp
Delay• Off: The headlight delay function will be deactivated.
• On: The headlight delay function will be activated.
For more details, refer to “Light” in chapter 5.

5-28
Instrument cluster
Convenience
ItemsExplanation
Welcome
mirror/light• On door unlock: The outside rearview mirrors are unfolded and the
welcome light turns on automatically when the doors are unlocked.
• On driver approach: The outside rearview mirrors are unfolded and the
welcome light turns on automatically when the vehicle is approached
with the smart key.
For more details, refer to ‘’Welcome System’’ in chapter 5.
Wireless
charging systemTo activate or deactivate the wireless charging system in the front seat.
For more details, refer to “Wireless cellular phone charging system” in
chapter 5.
Wiper/Lights
displayTo activate or deactivate the Wiper/ Light mode.
When activated, the LCD display shows the selected Wiper/Light mode
whenever you changed the mode.
Service interval
ItemsExplanation
Service IntervalIn this mode, you can activate the service interval function with mileage
(km or mi.) and period (months).• Off : The service interval function will be deactivated.
• On :You can set the service interval (mileage and months).

5-30
Instrument cluster
Cluster type A
Tripmeter/Trip computer
OBI3040011OBI3040011
„„Type AType A
„„Type BType B
The trip computer is a microcomputer-
controlled driver information system that
displays information related to driving,
when the ignition switch is in the ON
position. All stored driving information
(except odometer & Trip A & B) resets if
the battery is disconnected.Press the trip mode/reset button for less
than 1 second to select any mode as
follows:
* if equipped* if equipped
Tripmeter A
Tripmeter B
Distance to empty*
Average fuel consumption*
Instant fuel consumption*
Average speed*
Elapsed time*
Service Reminder*
TRIP COMPUTER

5-32
Instrument cluster
OQXI049120OQXI049120
Average fuel consumption (if
equipped) (l/100 km or MPG)
This mode calculates the average fuel
consumption from the total fuel used
and the distance since the last average
consumption reset. The total fuel used
is calculated from the fuel consumption
input. For an accurate calculation, drive
more than 300 m (0.18 miles).
Pressing the RESET button for more
than 1 second, when the average fuel
consumption is being displayed, clears
the average fuel consumption to zero
(--.-).
OQXI049121OQXI049121
Instant fuel consumption (if
equipped) (l/100 km or MPG)
This mode calculates the instant fuel
consumption of the last few seconds.

5-34
Instrument cluster
OQXI049123OQXI049123
Elapsed time (if equipped)
This mode indicates the total time
traveled since the last driving time reset.
Even if the vehicle is not in motion,
the driving time keeps going while the
engine is running.
The meter’s working range is from
00:00~99:59.
Pressing the RESET button for more than
1 second, when the driving time is being
displayed, clears the driving time to zero
(00:00).
Service reminder
OBI3040012OBI3040012
This mode displays the service interval
(mileage).
Digital Speedometer
OBI3040013OBI3040013
This message shows the speed of the
vehicle (km/h, MPH).