Page 294 of 486
6-38
Whilst driving
ESC operation
ESC 2 1 condition
When the ignition switch is in the ON
position, the ESC and the ESC OFF
indicator lights illuminate for approxi-
mately three seconds. After both
lights go off, the ESC is enabled.
When operating
When the ESC is in opera-
tion, the ESC indicator
O L J K W E O L Q N V
Page 295 of 486
6-39
06
‡ 6 W D W H
2 $ & 7 8
3 U H V V D Q G K R O G W K H ( 6 & 2 ) ) E X W W R Q
continuously for more than 3 sec-
onds. The ESC OFF indicator light
and/or message “Traction control and
ESC disabled” illuminates and a
warning chime sounds. In this state,
both the traction control function of
ESC (engine management) and the
brake control function of ESC (brak-
ing management) are disabled.
If the ignition switch is placed in the
LOCK/OFF position when ESC is off,
ESC remains off. Upon restarting the
vehicle, the ESC will automatically
turn on again.
Indicator lights
„ ESC indicator light (blinks)
„ ESC OFF indicator light (comes on)
2 7 '
2 7 '
When the ignition switch is in the ON
position, the ESC indicator light illu-
minates, then goes off if the ESC sys-
tem is operating normally.
The ESC indicator light blinks when-
ever the ESC is operating.
If the ESC indicator light stays on,
your vehicle may have a malfunction
with the ESC system. When this
warning light illuminates we recom-
mend that the vehicle be checked by
a HYUNDAI authorised repairer as
soon as possible.
The ESC OFF indicator light comes
on when the ESC is turned off with
the button.
WARNING
When the ESC is blinking, this
indicates the ESC is active:
Drive slowly and NEVER attempt
to accelerate. NEVER turn the ESC
off whilst the ESC indicator light is
blinking or you may lose control of
the vehicle resulting in an acci-
dent.
Page 319 of 486
6-63
06
The indicator () in the cluster dis-
play will initially illuminate white.
When the indicator (white) activated
in the previous ignition cycle, the sys-
tem turns on without any control.
If you press LKA button for more than
V H F R Q G V D J D L Q R U \ R X V H O H F W
Page 340 of 486
6-84
Whilst driving
i Information
‡ 'uring normal cruise control opera-
tion, when the SE 7 switch is activat-
ed or reactivated after applying the
brakes, the cruise control will acti-
vate after approximately 3 seconds.
7his delay is normal.
‡ Before activating the cruise control
function, the system will check to
verify that the brake switch is oper-
ating normally. 'epress the brake
pedal at least once after turning 2 1
the ignition or starting the vehicle.
Cruise control switch
2 $ ,
CRUISE/ 7 X U Q V F U X L V H F R Q-
trol system on or
off.
5 ( 6 5 H V X P H V R U L Q F U H D V H V F U X L V H
control speed.
6 ( 7 6 H W V R U G H F U H D V H V F U X L V H F R Q-
trol speed.
& $ 1 & ( / & D Q F H O V F U X L V H F R Q W U R O
operation.
To set Cruise Control speed
2 $ ,
3 X V K W K H & 5 8 , 6 ( button
on the steering wheel to turn the
system on. The CRUISE/
indicator on the LCD display will
illuminate.
2. Accelerate to the desired speed,
Z K L F K P X V W E H P R U H W K D Q P S K
N P K
i Information
For manual transmission vehicles, you
should depress the brake pedal at least
once to set the cruise control after
starting the engine.
Page 355 of 486
7-3
07
OAC3079001TU
The hazard warning flasher serves as
a warning to other drivers to exercise
extreme caution when approaching,
overtaking, or passing your vehicle.
It should be used whenever emer-
gency repairs are being made or
when the vehicle is stopped near the
edge of a roadway.
To turn the hazard warning flasher on
or off, press the hazard warning flash-
er button with the ignition switch in
any position. The button is located in
the centre fascia panel. All turn signal
lights will flash simultaneously.
‡ The hazard warning flasher oper-
ates whether your vehicle is run-
ning or not.
‡ The turn signals do not work when
the hazard flasher is on
HAZARD WARNING FLASHER IN CASE OF AN EMERGENCY
WHILST DRIVING
, I W K H H Q J L Q H V W D O O V Z K L O V W
G U L Y L Q J
‡ Reduce your speed gradually,
keeping a straight line. Move cau-
tiously off the road to a safe place.
‡ Turn on your hazard warning flash-
er.
‡ Try to start the engine again. If your
vehicle will not start, we recom-
mend that you contact a HYUNDAI
authorised repairer.
, I W K H H Q J L Q H V W D O O V D W D F U R V V-
U R D G R U F U R V V L Q J
If the engine stalls at a crossroads or
crossing, if safe to do so, move the
shift lever to the N (Neutral) position
and then push the vehicle to a safe
location.
Page 381 of 486
7-29
07
OAC3079013R
5. Plug the compressor power cord
(4) into the vehicle power outlet.
6. With the ignition switch in the ON
position, switch on the compressor
and let it run for approximately 5~7
minutes to fill the sealant up to
proper pressure. (refer to the Tyre
and Wheels, chapter 2). The infla-
tion pressure of the tyre after filling
is unimportant and will be checked/
corrected later.
Be careful not to overinflate the
tyre and stay away from the tyre
when filling it.
CAUTION
7 \ U H S U H V V X U H
' R Q R W D W W H P S W W R G U L Y H \ R X U Y H K L-
F O H L I W K H W \ U H S U H V V X U H L V E H O R Z
S V L N 3 D 7 K L V F R X O G U H V X O W L Q
D Q D F F L G H Q W G X H W R V X G G H Q W \ U H
I D L O X U H
7. Switch off the compressor.
8. Detach the hoses from the sealant
bottle connector and from the tyre
valve.
Return the Tyre Mobility Kit to its stor-
age location in the vehicle.
WARNING
& D U E R Q P R Q R [ L G H
' R Q R W O H D Y H \ R X U Y H K L F O H U X Q Q L Q J
L Q D S R R U O \ Y H Q W L O D W H G D U H D I R U
H [ W H Q G H G S H U L R G V R I W L P H & D U E R Q
P R Q R [ L G H S R L V R Q L Q J D Q G V X I I R F D-
W L R Q F D Q R F F X U
Page 383 of 486
7-31
07
4. Adjust the tyre inflation pressure to
the recommended tyre inflation.
With the ignition switched on, pro-
ceed as follows.
- 7 R L Q F U H D V H W K H L Q I O D W L R Q S U H V-
V X U H Switch on the compressor.
To check the current inflation
pressure setting, briefly switch off
the compressor.
- 7 R U H G X F H W K H L Q I O D W L R Q S U H V-
V X U H Press the button (9) on the
compressor.
NOTICE
' R Q R W O H W W K H F R P S U H V V R U U X Q I R U
P R U H W K D Q P L Q X W H V R W K H U Z L V H
W K H G H Y L F H Z L O O R Y H U K H D W D Q G P D \
E H G D P D J H G
i , Q I R U P D W L R Q
The pressure gauge may show higher
than actual reading when the compres-
sor is running. To get an accurate tyre
reading, the compressor needs to be
turned off.
CAUTION
, I W K H L Q I O D W L R Q S U H V V X U H L V Q R W
P D L Q W D L Q H G G U L Y H W K H Y H K L F O H D
V H F R Q G W L P H U H I H U W R ' L V W U L E X W L Q J
W K H V H D O D Q W 7 K H Q U H S H D W V W H S V W R
8 V H R I W K H 7 0 . P D \ E H L Q H I I H F W X D O
I R U W \ U H G D P D J H O D U J H U W K D Q D S S U R [-
L P D W H O \ P P L Q
: H U H F R P P H Q G W K D W \ R X F R Q W D F W D
+ < 8 1 ' $ , D X W K R U L V H G U H S D L U H U L I W K H
W \ U H F D Q Q R W E H P D G H U R D G Z R U W K \
Z L W K W K H 7 \ U H 0 R E L O L W \ . L W
WARNING
7 K H W \ U H L Q I O D W L R Q S U H V V X U H V K R X O G
P H H W W K H V W D Q G D U G
Page 385 of 486
7-33
07
When towing your vehicle in an emer-
gency without wheel dollies:
1. Place the ignition switch in the
ACC position.
2. Place the shift lever in N (Neutral).
3. Release the parking brake.
CAUTION
) D L O X U H W R S O D F H W K H V K L I W O H Y H U L Q 1
1 H X W U D O P D \ F D X V H L Q W H U Q D O G D P-
D J H W R W K H W U D Q V P L V V L R Q
5 H P R Y D E O H W R Z L Q J K R R N
OAC3079015TU
1. Open the tailgate, and remove the
towing hook from the tool case.
OAC3079016TU
2. Remove the hole cover by press-
ing the lower part of the cover on
the bumper.
3. Install the towing hook by turning it
clockwise into the hole until it is
fully secured.
4. Remove the towing hook and
install the cover after use.
