2021 GENESIS G80 sensor

09
9-51
Engine compartment fuse panel
Fuse NameFuse Rating Circuit Protected
IG1 30A
IG1 Relay
ECU3 30A
Engine Control Realy
IG2 30A
IG2 Relay
ACC 30A
ACC Relay
ECU2 10A
ECM
EWP 20A
Electronic Water Pump
MODULE2 10A
Smart Cruise Control Radar, Front Radar LH/RH, 4WD ECU
SENSOR5 10A
Electronic Oil Pump
MDPS2 10A
MDPS Unit
IEB4 10A
IEB Unit
ACTIVE HOOD 10A
Active Hood Control Unit
TCU2 15A
P/N Relay, TCM
SENSOR3 10A[G4KR] Oxygen Sensor (Up/DOWN)
[G6DS] Oxygen Sensor #1~#2
SENSOR2 10A[G4KR] E/R Junction Block(A/C Relay), Oil Control Valve
(Exhaust), Oil Pump Solenoid Valve, Purge Control
Solenoid Valve
RCV Control Solenoid Valve, Canister Close Valve
[G6DS] E/R Junction Block(A/C Relay), RCV Control
Solenoid Valve #1~#2, Purge Control Solenoid Valve, Oil
Pump Solenoid Valve,
Oxygen Sensor #3~#4, Oil Control Valve #1~#4, Canister
Close Valve
SENSOR1 10AG4KR] Injector #1~#4, E/R Junction Block(Fuel Pump
Relay)
[G6DS] Injector #1~#6(MPI), E/R Junction Block(Fuel
Pump Relay)
IGN COIL 15A[G4KR] Ignition Coil #1~#4
[G6DS] Ignition Coil #1~#6
SENSOR4 15A
Cooling Fan Motor
ECU4 20A
ECM
WASHER 15A
Washer Relay

09
9-57
Battery junction block
Fuse NameFuse Rating Circuit Protected
B+5 125A
E/R SUB Junction Block (B+)
B+6 100ARear Junction Block(Fuse(B+1, AMP, P/Window RH, P/Seat
RR, ECS, Presafety Seat Belt1, Child Lock))
B+7 100ARear Junction Block(Fuse(B+3, S/Heater RR LH,
S/Heater RR RH, Power Trunk, P/Door DRV, P/Door PASS))
B+8 100ARear Junction Block(Fuse(B+2, B+4, P/Door RR LH,
P/Door RR RH, Presafety Seat Belt2))
AMS 10A
Battery Sensor
RWS 100A
RWS MODULE

09
9-63
Exterior Care
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning and
caution statements that appear on the
label.
Finish maintenance
Washing
To help protect your vehicle’s finish from
rust and deterioration, wash it thoroughly
and frequently at least once a month
with lukewarm or cold water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to the
removal of any accumulation of salt, dirt,
mud, and other foreign materials. Make
sure the drain holes in the lower edges
of the doors and rocker panels are kept
clear and clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar deposits
can damage your vehicle’s finish if not
removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits. A mild soap, safe for use on
painted surfaces, should be used.
After washing, rinse the vehicle
thoroughly with lukewarm or cold water.
Do not allow soap to dry on the finish.High-pressure washing
• When using high-pressure washers,
make sure to maintain sufficient
distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.
• Do not spray the camera, sensors or
its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause
the device to not operate normally.
• Do not bring the nozzle tip close to
boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
WARNING
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by water
before getting on the road. If braking
performance is impaired, dry the
brakes by applying them lightly while
maintaining a slow forward speed.
APPEARANCE CARE