2021 GENESIS G70 Turn

7-63
7
Maintenance
9. - Turn signal lamp (A)
Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
- Back-up lamp (B)
Insert a new bulb by pushing it in
into the socket.
10. Install the socket into the assem-
bly by aligning the tabs on the
socket with the slots in the
assembly. Push the socket into
the assembly and turn the socket
clockwise.
11. Reinstall the lamp assembly to
the body of the vehicle.High Mounted Stop Lamp
Replacement
If the high mounted stop lamp (LED)
(1) does not operate, have the sys-
tem be checked by an authorized
retailer of Genesis Branded prod-
ucts.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the LED lamp, for it may dam-
age related parts of the vehicle.
License Plate Light
Replacement
If the license plate lamp (LED) (1)
does not operate, have the system
be checked by an authorized retailer
of Genesis Branded products.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the LED lamp, for it may dam-
age related parts of the vehicle.
OIK077040OIK077041

7-75
7
Maintenance
The emission control system of your
vehicle is covered by a written limited
warranty. Please see the warranty
information contained in the Owner’s
Handbook & Warranty Information
booklet in your vehicle.
Your vehicle is equipped with an
emission control system to meet all
applicable emission regulations.
There are three emission control
systems, as follows.
(1) Crankcase emission control sys-
tem
(2) Evaporative emission control sys-
tem
(3) Exhaust emission control system
In order to ensure the proper func-
tion of the emission control systems,
it is recommended that you have
your vehicle inspected and main-
tained by an authorized retailer of
Genesis Branded products in accor-
dance with the maintenance sched-
ule in this manual.For the Inspection and
Maintenance Test (with Electronic
Stability Control (ESC) system)
• To prevent the vehicle from mis-
firing during dynamometer test-
ing, turn the Electronic Stability
Control (ESC) system off by
pressing the ESC switch (ESC
OFF light illuminated).
• After dynamometer testing is
completed, turn the ESC system
back on by pressing the ESC
switch again.1. Crankcase Emission Control
System
The positive crankcase ventilation
system is employed to prevent air
pollution caused by blow-by gases
being emitted from the crankcase.
This system supplies fresh filtered air
to the crankcase through the air
intake hose. Inside the crankcase,
the fresh air mixes with blow-by
gases, which then pass through the
PCV valve into the induction system.
2. Evaporative Emission Control
System Including Onboard
Refueling Vapor Recovery
(ORVR)
The Evaporative Emission Control
System is designed to prevent fuel
vapors from escaping into the atmos-
phere. The ORVR system is
designed to allow the vapors from
the fuel tank to be loaded into a can-
ister while refueling at the gas sta-
tion, preventing the escape of fuel
vapors into the atmosphere.
NOTICE
EMISSION CONTROL SYSTEM

BULB WATTAGE
8-3
88
Specifications, Consumer information and Reporting safety defects
Light Bulb Bulb Type Wattage
FrontType AHeadlampHigh HB3 60W
Low HB3 60W
Turn signal lamp PY28/8W 28W
Daytime running light & Parking lamp LED LED
Side marker LED LED
Type BHeadlampHigh/Low LED LED
High LED LED
Turn signal lamp LED LED
Daytime running light & Parking lamp LED LED
Side marker LED LED
RearTail/Stop lamp LED LED
Stop lamp LED LED
Turn signal lamp P27W 27W
Back-up lamp W16W 16W
Side marker LED LED
License plate lamp LED LED
High mounted stop light LED LED
InteriorMap lamp LED LED
Room lampLEDLED
Glove box lampLEDLED
Trunk lampLEDLED
Vanity mirror lampLEDLED