2021 CHEVROLET CORVETTE mirror

2
Manual Shift Paddles
INSTRUMENT PANEL
Stability Control Off
Low Tire Pressure
Brake System
Antilock Brake System
Stability Control Active
Door Ajar
Cruise Control
P ARK Electric Parking Brake
Charging System
Oil Pressure
Engine Coolant Temperature
Service Electric Parking Brake
Traction Control Off
Low Fuel
Head-Up Display ControlsF
Cruise Control/ Z-Mode Buttons
Turn Signal Lever/Exterior Lamps ControlWindshield Wipers Lever
Hood Release/ Trunk Release Buttons
Audio Favorite Station Buttons
Audio Volume Buttons
Driver Information Center/Heated Steering WheelF/Voice Recognition Control Buttons
Steering Wheel Adjustment Control
Electric Parking Brake Switch
Customizable Instrument Cluster
Power Folding MirrorF/Window Controls
SYMBOLS

4
REMOTE KEYLESS ENTRY TRANSMITTER (KEY FOB)
X2 Hatch/Trunk Release
Press and release followed by press and hold to open the hatch/trunk.
Lower Convertible TopF
Press and release the Unlock button and then press and hold the button to lower the top.
Press and release the Lock button and then press and hold the button to open the engine compartment.
Vehicle Locator/Panic Alarm
Press and release to locate your vehicle. The horn sounds and lights flash 3 times.
Press and hold to activate the alarm. Press again to cancel the alarm.
KEY RELEASE
If vehicle power is lost, press the button on the side of the transmitter to pull out the key. Use the key to open the door. Pull the looped cord below the instrument panel to open the hood for access to the battery.
Lock
Press to lock all doors and the fuel door. Press again to fold the power mirrorsF.
Unlock
Press to unlock the driver’s door and the fuel door only or all doors, based on vehicle settings. Press and hold for 3 seconds to open all windows.
To enable automatic mirror foldingF when using the Lock and Unlock buttons, go to Settings > Vehicle > Comfort and Convenience > Remote Mirror Folding.
[ Remote Vehicle Start
Press twice to start the engine from out-side the vehicle. The turn signal lamps will flash. After entering the vehicle, turn on the ignition.
X2 Hood Release
Press and release followed by press and hold to open the hood.
F Optional equipment
Note: To change or enable some Remote Keyless Entry settings, go to Settings > Vehicle > Remote Lock, Unlock, Start. See Keys, Doors and Windows in your Owner’s Manual.
The system enables operation of the doors, hatch/trunk, and hood without removing the Remote Keyless Entry (RKE) transmitter from your pocket or purse. The transmitter must be within 3 feet of the hatch/trunk, hood or door being unlocked.
KEYLESS UNLOCKING
With the RKE transmitter within range:
Press the driver’s door handle touchpad (A) to unlock the driver’\
s door only or all doors.
Press the passenger’s door handle touchpad to unlock all doors.
KEYLESS LOCKING
Press the Lock button on the RKE transmitter or interior door panel to lock all doors.\
If Passive Locking is turned on in the Settings menu, all doors will loc\
k automatically after a short delay once all doors are closed.
See Keys, Doors and Windows in your Owner’s Manual.
KEYLESS ACCESS SYSTEM
A

7F Optional equipment
SEAT ADJUSTMENTS
A. Seat Cushion Adjustment
Move the horizontal control to move the seat forward or rearward and to tilt, raise or lower the seat.
B. Seatback Adjustment
Move the vertical control to recline or raise the seatback.
C. Lumbar/Side Bolster AdjustmentF
Press the round control forward or rearward to adjust the lumbar support and up or down to adjust the side bolsters.
SET DRIVER’S SEAT MEMORY POSITIONSF
1. With the vehicle On and in Park, adjust the driver’s seat, power outside mirrors, and power steering columnF to the desired positions.
2. Press and release the SET button on the driver’s door. A beep will sound.
3. Immediately press and hold button 1 or 2 until two beeps sound. Use the button that matches the Driver Information Center welcome message indicating driver 1 or 2. To identify each Remote Keyless Entry transmitter, one has a chrome flag \
and the other has a black flag.
To store seat and power steering column positions for more clearance whe\
n exiting the vehicle, repeat these steps using the EXIT button instead of button 1 or 2.
RECALL DRIVER’S SEAT MEMORY POSITIONSF
Press and hold button 1, 2 or EXIT until the set position is reached.
The memory/exit positions can be programmed to be recalled automatically\
when the ignition is turned on/off (for exit recall, the driver’s door must b\
e opened).
To set the automatic recall options, go to Settings > Vehicle > Seating \
Position > Seat Entry Memory and Seat Exit Memory.
SET PASSENGER’S SEAT MEMORY POSITIONSF
1. With the vehicle On and in Park, adjust the passenger’s seat to the d\
esired position.
2. Press and release the SET button on the passenger’s door. A beep will sound.
3. Immediately press and hold button 1 or 2 until two beeps sound.
To store a seat position for more clearance when exiting the vehicle, re\
peat these steps using the EXIT button instead of button 1 or 2.
To recall a setting, press and hold button 1, 2 or EXIT until the set position is reached.
See Seats and Restraints in your Owner’s Manual.
POWER SEATS
CAB