2021 AUDI Q8 roof rack

4M8012721BF

Lights and Vision

— The automatic dimming mirrors do not dim Windshield wipers
when the interior lighting is turned on or
the reverse gear is selected. Switching the windshield wipers on

Sun visors



RAZ-0253 Fig. 39 Roof headliner: sun visor
Sun visor
The sun visors can be moved out of their brackets
and turned toward the doors (a).

They can also be moved back and forth length-
wise in this position.


Vanity mirror Fig. 42 Lever: rear window wiper
The mirror light switches on when the cover over > Move the windshield wiper lever © to the cor-
the vanity mirror @) opens. responding position:
Windshield wipers off
@ :
Applies to: vehicles with manual sunshade @ Rain sensor/intermittent mode. The wind-
shield wipers switch on once the vehicle speed
exceeds approximately 2 mph (4 km/h) and it is
raining. The higher the sensitivity of the rain sen-
sor that is set (switch ©) to the right), the earlier
the windshield wipers react to moisture on the
windshield. You can deactivate the rain sensor
mode, which switches the interval mode on. In
intermittent mode, you can adjust the interval
time using the switch ©.
> Applies to: MMI: Select on the home screen:

big ns OsResnwindowssunsieds VEHICLE > Light & Visibility > Rain sensor.
Rear window sunshade @® Slow wiping
> Pull the sunshade out and attach it to the re- @ Fast wiping
tainer on the luggage compartment lid.
ggeg P @ Single wipe. If you hold the lever in this posi-
tion longer, the wipers switch from slow wiping
to fast wiping.
57
>

Storage and convenience

Roof rack
General information
Applies to: vehicles with roof rack mount

x
Ss
$ > a
a

Fig. 80 Roof rail: mounting points
If luggage or cargo is to be carried on the roof,
you must observe the following:
— These roof racks are the basis for a complete
roof rack system. Only roof racks that are suita-
ble for your vehicle may be used. Audi recom-
mends roof racks and attachments from the
Audi Genuine Accessories program.
— Make sure the roof rack is mounted on the vehi-
cle only at the specified locations > fig. 80.
— Note the permitted axle load, permitted total
weight, and permitted roof load of your vehicle
=> page 314. The roof load is the total of the
weight of the roof rack, the attachments and
the cargo you are carrying. However, you must
also note the permitted load of the carrier sys-
tem being used.


— Distribute the cargo evenly on the roof rack
and do not exceed the maximum width or
the maximum total roof load weight.
— Before every trip, all bolts and connections
on the roof rack must be checked. Tighten
them if necessary and recheck them regular-
ly. If you do not do this, there is a higher risk
of
the roof rack or the attachments loosen-
ing or falling off.


Z\ WARNING
— Follow the installation instructions provided
with the roof rack system. If you do not se-
cure the roof rack system and objects on the
roof correctly, they could come loose from
the vehicle and cause an accident.
— The risk of an accident increases when using
a roof rack system, because it changes the
driving characteristics by shifting the center
of gravity and/or the increasing the surface
area exposed to wind. You may need to
adapt your driving style and speed to the
current conditions. Audi recommends that
you do not drive faster than 80 mph (130


km/h).

88
@) Note
— If you use other roof luggage rack systems
or do not install the roof racks as specified,
then any damage to the vehicle is not cov-
ered by the warranty. Carefully follow the
assembly and installation instructions in-
cluded with the roof rack carrier system.
—To reduce the risk of damage, you must re-
move the roof rack and attachment before
taking your vehicle through an automatic
car wash.
— Make sure that the luggage compartment
lid and the panoramic glass roof* do not
come into contact with objects on the roof
when they are open.
(4) For the sake of the environment
Energy usage will increase because of the in-
creased wind resistance. Remove the roof rack
when you are no longer using it.

4M8012721BF
Storage and convenience

Installing the roof rack
Applies to: vehicles with roof racks supplied by the factory

= 3 £
= ira a


Fig. 81 Roof rail: installing a roof rack
The roof rack set consists of a front and rear roof
rack, the cover profile and a socket wrench. On
the inner side of the roof rail, there are two holes
for the rear roof rack. To prevent the front and
rear roof racks from being switched during instal-
lation, there are three holes on the left inner side
and two holes on the right inner side > page 88,
fig. 80.
> Before mounting the roof rack, open the cap @
upward.
> Use the socket wrench (2) to loosen the left and
right screw in the direction of @ until resist-
ance is felt. Make sure the arrow on the socket
wrench and the arrow on the screw line up ex-
actly.
> Clean the rubber washers (4) and the roof rail
around the mounting points.
> Carefully place the roof rack over the holes in
the roof rail. Make sure the sticker is on the left
side of the vehicle and the imprinted arrow
points in the direction of travel.
> Place the pins @) into the holes. The claw fas-
tener G) must engage into the edge of the roof
rail. Make sure the rubber washers () lie flat on
the roof rail.
> Tighten the screw in the direction of @) using
the torque wrench @). Make sure the arrow on
the socket wrench and the arrow on the screw
line up exactly. The required tightening specifi-
cation is 4.5 ft lbs (6 Nm).
> Repeat these steps for the other mounting
points for the roof rack.

ZA\ WARNING
When installing a factory-supplied roof rack
system on the roof rail, the ESC will use sen-
sors to adapt itself to the different center of
gravity if it changes because of carrying a
load. This does not occur when using other
roof rack systems, so the risk of an accident
will increase.
Installing the attachments
Applies to: vehicles with roof racks supplied by the factory

> Remove the cap ©) to mount attachments on
the roof rack > page 89, fig. 81.
» Slide the attachment into the T-groove ().
> Tighten the attachment according to the roof
rack installation instructions.
> Close the cap ©).
Installing the cover profile
Applies to: vehicles with roof racks supplied by the factory
» After you have mounted the attachments, seal
the openings in the T-groove @) > page 89,
fig. 81 with the cover profile (8). The cover pro-
file must not be installed under the caps ©.
> If you do not want to use the attachment, seal
the whole T-groove (7) with the cover profile @).
» If necessary, shorten the cover profile @) so
that it matches the length of the open sections
of the T-groove. The caps ©) must be closed.
89

Driving

There is a malfunction in the "P" button on the
selector lever. The “P” gear is automatically en-
gaged when you turn off the engine. Drive to an
authorized Audi dealer or authorized Audi Service
Facility immediately to have the malfunction cor-
rected.
fs} Danger of rolling away! P not possible.
Please apply parking brake
— The parking lock was released using the emer-
gency
release > page 100. Or:
— The parking lock can no longer be engaged.
Drive to an authorized Audi dealer or author-
ized Audi Service Facility immediately to have
the malfunction corrected. Secure the vehicle
against rolling before exiting the vehicle
> page 96.
Move selector lever to automatic position
The transmission has switched out of tiptronic
mode. Switch back to automatic mode with the
selector lever > page 99.
Drive system
A new vehicle must be broken in within the first
1,000 miles (1,500 km) so that all moving parts
work smoothly together, which helps to increase
the service life of the engine and other drive com-
ponents.
Do not drive higher than two-thirds of the maxi-
mum permitted engine RPM during the first 600
miles (1,000 km) and do not use full accelera-
tion. The engine can be increased RPM gradually
during the next 300 miles (500 km).
Conventional and mild hybrid drive system
Applies to: vehicles with a conventional drive system or a mild
hybrid drive system
Vehicles with a conventional or mild hybrid drive
system are powered by a combustion engine. It
uses fuel to recover energy.
Vehicles with a mild hybrid drive system have ad-
ditional battery technology.
102

aire (alee Madey neat iN ede (Tue A
driving

Your driving style greatly influences the amount
of fuel and energy consumed, the environmental
impact, and the wear on the engine, brakes, and
tires. Note the following information for efficient
and environmentally-conscious driving:
— Turn off electrical equipment that is not need-
ed, for example seat heating*.
— Anticipate upcoming traffic situations while
driving to avoid unnecessary acceleration and
braking.
— Avoid driving at high speeds.
— Avoid adding extra weight to the vehicle if pos-
sible, for example by not leaving roof racks or
bike racks installed when they are not needed.
— Make sure the tire pressure is correct.
— Have maintenance performed regularly on the
vehicle.
— Do not let the engine run while the vehicle
parked.
— Do not drive with winter tires during the summ-
er.
— Use the Start/Stop system.
— Utilize the engine braking effect.
— Avoid driving short distances when possible.
(i) Tips
The amount of noise produced by the vehicle
can increase significantly when driving with a
sporty style. Show respect to others around
you and the environment with the way you op-
erate your vehicle, especially at night.
Sees
Your vehicle is equipped with an intelligent ener-
gy management system for distributing electrici-
ty. This significantly improves the starting ability
and increases the vehicle battery life.
@ Tips
—If you drive short distances frequently, the
vehicle battery may not charge enough
while driving. As a result, convenience func-
tions for electrical equipment may be tem-
porarily unavailable.

Radio

Radio
General information
Selecting the radio
ie) | ey
See) os 2 )
\S ™
3 Pa): 4
(ones
ro
* a 106.7 ana
mao
RADIO —@
Saray
22 Lim)
i
4 Qi:
aa
Fig. 148 Upper display: SiriusXM channel list
Depending on the vehicle equipment, the radio
may support the FM, AM, and SiriusXM (satellite
radio) frequency bands. Using the HD Radio re-
ceiver* also allows you to receive radio stations
on the FM and AM bands in digital format.
Depending on the vehicle equipment and the se-
lected station list, the following information will
be displayed:
@ Station list
Shows the stations that are currently availa-
ble. The station list updates automatically.
Stations @
For example, the station name may be dis-
played depending on availability.
HD Radio technology
FM/AM stations that can be received by digi-
tal radio are marked with the HD Radio tech-
nology symbol H).
If reception quality declines, the radio auto-
matically switches to the analog FM/AM sta-
tion depending on availability.
@ Additional audio programs
Digital HD Radio stations may contain multi-
ple additional audio programs. If you lose re-
ception, the additional audio programs will
212

be muted since they can no longer be re-
ceived.
Radio ID
Your radio ID and contact data for your satel-
lite radio provider are displayed.
Channel number
® No reception e®
The station cannot be received.
In addition to the symbols for the usual frequen-
cy bands, the following information may also be
available depending on vehicle equipment:

Symbol | Description
The station provides information in
the background for an online station
alternative. Online station tracking
must be switched on for this
> page 218.

The station is received through the In-
ternet.

The system attempts to receive the
station/podcast through the Internet.
G) Tips
— Contact the SiriusXM* provider if you would
like to receive satellite programming.

— Buildings, tunnels, bridges, open areas, oth-
er vehicles or objects on the vehicle roof can
affect reception.
— Satellite radio* is not available in all re-
gions.
Adjusting the radio using the MMI
> Applies to: MMI: To set a frequency band, select
on the home screen: RADIO > Source a catego-
ry.
> Applies to: MMI: To set a station, select on the
home screen: RADIO > Source > a category >a
station/podcast*.
> To select a frequency, follow the instructions
under > page 214, Free text search.
Adjusting the radio using the multifunction
steering wheel
Requirement: radio mode must be on. >

4M8012721BF
Wheels

Production options weight
means the combined weight of
those installed regular production
options weighing over 5 lbs.
(2.3 kg) in excess of those stand-
ard items which they replace, not
previously considered in curb
weight or accessory weight, in-
cluding heavy duty brakes, ride
levelers, roof rack, heavy duty
battery, and special trim.
Radial ply tire
means a pneumatic tire in which
the ply cords that extend to the
beads are laid at substantially
90 degrees to the centerline of
the tread.
Recommended inflation
pressure
see > page 259, Cold tire infla-
tion pressure.
Reinforced tire
means a tire designed to operate
at higher loads and at higher in-
flation pressures than the corre-
sponding standard tire. Rein-
forced tires may be identified as
“XL”, “xl”, “EXTRA LOAD”, or “RF”
on the sidewall.
Rim
means a metal support for a tire
or a tire and tube assembly upon
which the tire beads are seated.
Rim diameter
means nominal diameter of the
bead seat. If you change your
wheel size, you will have to pur-
chase new tires to match the new
rim diameter.
Rim size designation
means rim diameter and width.
Rim width
means nominal distance between
rim flanges.
Sidewall
means that portion of a tire be-
tween the tread and bead.
Speed rating (letter code)
means the speed at which a tire is
designed to be driven for extend-
ed periods of time. The ratings
range from 93 mph (150 km/h)
to 186 mph (298 km/h) > table
on page 257. You may not find
this information on all tires be-
cause it is not required by law.
The speed rating letter code,
where applicable, is molded on
the tire sidewall and indicates the >
261

Index


REAR (climate control system) ............- 91
Recirculation Mode savin ss swims x sce 6 4 wee 92
Recuperationsses «= ses + 2 samen ¥ ¢ ees 9 coe 16
REfrigeranit Ollvs sz wavew xe exes ox meme 2 eae 314
RETUGLING « « wews 6 a news oe ees Fe ema ee 239
Remote access authorization (key user) ..... 33
Remote control
Garage door opener........se.ceeeeeees 48
Remote control key 39
Convenience opening and closing......... 47
Key replacement.............02-.00 eee 39
| Al
PANIGfUNCHION ¢ s wees ¢ gaseu aan ss een 39
Replacing the battery...............00. 41
Unlocking and locking..............0008 40
also refer to Vehicle key..............-. 39
Remote controlled parking.............. 173
Remote park assist plus
refer to Remote controlled parking...... 173
Remote park assist plus with garage function
refer to Remote controlled parking...... 173
Removing the caps (wheel bolts)......... 289
REPAIIS sess 6s mmo © 3 ees © a sume SF er oo 308
Replacement key.........--22e eee eee 39
Replacement parts............--..20--5 310
Replacing fuses........... 2. eee e ee eee 298
Reporting
Safety Defects................ 310
RIMS 0. eee eee eee eee 271
Cl@SNiNG's ¢ = 22m ¢ » wemn 2 2 ees yo eee sz Be 282
Road carrier... 0.6.2... eee eee eee eee 112
Rolling... .. cece cece eee eee eee 96
Rolling
ability
Electromechanical parking brake........ 106
Transmission idleis . isan si maven oo ccomea soo 98
Roof
refer to Panoramic glass roof............ 47
Roof LOad ©» awevis oo cvewsss v seavans ao sueeun ao came 314
ROORKACK asia + aon os waren 6 e naene a 2 BOR He 88
also refer to Roof rack..........--..000. 88
Route guidance
StOPPING ..... cee eee eee eee eee 204
also refer to Navigation............... 200
Running direction (tires)..............-. 291
324
Ss
Safety belts. ...... 0.0... eee eee eee 68
GCl@aNiNG ies « s wei + y ewe » eon ee Dew gE 283
LOEKING sexes ico seesene xe emevene ww maevare ¥ w anetese © 79
Securing child safety seats.............. 79
Satellite map...... 2... eee eee eee 207
Saving fuel
Energy consumers..........-.2-.020005 L7
Recuiperationts s sacs s zaee 5 s gees & x geome e 16
Screen
refer to Touch display ...........0e0eeee 18
SGrEWALIVET iss x = caves x = sae & & eerR 8 & OG s 286
Search function
refer to Free text search............... 227
Seat:heating « sci owes 2 wawn se meen 6 ¥ owe 92
Seats
Adjusting the front seats............... 63
Adjusting the rear seats................ 65
ClOaniNiG:<« = s gees + sees s been ge wees ae: 283
FOL Giaiss o wscass vo areas 6 Hama v Fame vO 86
Front passenger’s seat adjustment....... 65
Head restraititSies x « saws + = semis + eee eo 67
Massage function..........0seeeeee eee 63
Memory function..............--000 00 71
Resetting the position.................. 65
Storing aseat profile................... 71
Seat vertilationsecs so sexes 2 sce 2 2 orm 9 oo 92
Securing the vehicle............-..2+--5- 96
Selecting a source (media).............. 223
Selector lever cs x « news ¢ ¢ hoes ss eee oP eS 97
Sensors
COVETAGE ALCS « cercx : s wow so wegs + Rares o 122
LOCATIONS race x « canzone » © camsuae » & sunoane « @ meas 123
Service interval display................. 254
Setting measurement units.............. 233
S@ttiNGSiog « 5 wes = © ewes a eee ¢ Ree § Go Be 233
Announcements and tones............. 233
Bluetooth.....................000008 234
Dateanid titties: + saws x 2 eee « «ewe gs 233
LANGUAGE « sesso vo sens oo memes vo ERE vo es 233
Measurement units...............0005 233
Medidicn = 2 gaws : «meee s Hoon 4 > eu os ee 227
Navigationiccs « weve + even 6+ semen sv meres 210
Radio... 2.6... ce cece eee eee eee eee 218
SOUNG :geue ss wee 5 s seme fs meee Ee eee 233
SySteMss «+ assva 2 e eesen 2 v eeie 2 8 eae Foes 233