2021 AUDI Q2 automatic gearbox

Driving
R - Reverse gear
Reverse gear should only be engaged when the
vehicle is stationary and the engine is idling
^A-

To move the selector lever to position R, release
the selector Lever lock and at the same time
press the brake pedal.
N - Neutral
In this position, the gearbox is in neutral.
D/S - Drive/Sport (standard position for
driving forwards)
In selector Lever position D/S, the gearbox can be
operated in either the standard drive mode (D) or
in sport mode (S). To select sport mode (S), brief­
ly pull the selector lever back. The gearbox will
switch back to drive mode (D) if
you
pull the se­
lector lever again. The selected driving mode is
shown in the instrument cluster display.
In the standard drive mode (D), the gearbox au­
tomatically selects the best gear ratio. This de­
pends on the engine
load,
the road speed and the
driving style.
In Sport mode S, the gearbox makes full use of
the engine power. When accelerating the gear
shifts may be noticeable.
Press the brake pedal when moving the selector
lever from N to D/S if the vehicle is stationary or
at speeds below 2 km/h
o A-

E - Efficiency*
In efficiency mode
^>page
131, Audi drive se­

lect,
the gearbox selects the next gear at lower
engine speeds. Earlier upshifts give improved
fuel economy because the full power reserves of
the engine are not used.
In this mode, an
E
is shown on the instrument
cluster display instead of
a D
^>Fig.
75.

CO

< o rN
iv
rN
t-H
o < 00

A,
WARNING
- The car can roll away even if the ignition is
switched off.
- Never move the selector lever to
R
or P
when driving, as this could cause an
acci­

dent.
- In all selector lever positions (except P) the
vehicle must always be held with the foot
brake when the engine is running. This is be­
cause an automatic gearbox still transmits
power even at idling speed, and the vehicle
tends to "creep" - risk of accident!
- The accelerator pedal must on no account
be pressed inadvertently when a gear is en­
gaged with the vehicle stationary. The
vehi­

cle could otherwise start moving immedi­
ately (in some cases even if the parking
brake is engaged) and possibly cause an ac­
cident.
- Do not press the accelerator while selecting
a gear with the vehicle stationary and the
engine running, as this could cause an
acci­

dent.
- The driver should never get out of the
vehi­

cle when the engine is running and a gear is

engaged.
If
you
have to Leave your vehicle
while the engine is running, you must apply
the parking brake and engage the parking
lock P.
- To avoid accidents, apply the parking brake
and
put
the selector lever in position
P
be­
fore opening the bonnet and working on the
vehicLe with the engine running. Please ob­
serve the important safety warnings

^>page
295, Working on components in
the engine compartment.
© Note
- Audi drive select: You can select the sport
program for gear changes by activating the
dynamic mode
^>page
131. The instru­
ment cluster display will show
S
instead of
D.
- If the lever is moved accidentally to
N
when

driving,
take
your
foot off the accelerator
and
let
the engine speed drop to idling be­
fore selecting
D
or
S
again.
- It is not possible to move the selector lever
out of position
P
if the electrical power sup­
ply fails. In this case, the selector lever can
be released manually. Left-hand drive
vehicles
^page
93, right-hand drive
vehicles
<^>page
94.
87

Driving
©
y Note

If the selector lever does not lock automati­
cally, a malfunction has occurred. In this case,
the power transmission is interrupted to pre­
vent the vehicle from moving unintentionally.
Proceed as follows to engage the selector lev­
er lock again:
- Applies to vehicles with 6-speed gearbox:
Briefly press the brake pedal.
- Applies to vehicles with 7-speed gearbox:
Press the brake pedal. Move the selector
lever to position
P
or
N
and then select a
gear.
- If the vehicle does not move forwards or
backwards even though a gear is selected,
proceed as follows:
- If the vehicle does not move in the desired

direction,
the system may have failed to en­
gage the gear correctly. In this case, press
the brake pedal and select the gear again.
- If the vehicle still does not move in the de­
sired direction, a system malfunction has

occurred.
Seek professional assistance and
have the system checked.
General notes on driving an automatic
Applies to: vehicles with automatic gearbox

Fig.
77 Detail of the centre console: Selector lever with in­
terlock button
Starting the engine

•
Move the selector Lever to
P
or N. In the case of
Low outside temperatures (below -10 °C), the
engine can only be started when the selector
lever is in position P.
Driving away from a standstill

•
Press and hold the brake pedal.

•
Press and hold the interlock button (the button
in the selector lever handle), set the selector
lever to the desired position (e.g. D)
^>page
86
and release the interlock button.

•
Wait for the gearbox to engage the gear (a
slight movement can be felt).

•
Release the brake and press the accelerator
There are several convenient functions to help
you drive away on gradients
^page
83.
Stopping briefly

•
Press the brake pedal to hold the vehicLe when
stationary (for instance at traffic lights).

•
Do not press the accelerator.

•
To prevent the vehicLe from rolling away, apply
the parking brake before moving off on steep
gradients
•=>^
and
•=>(]).

• As soon as you acceLerate as normal, the park­
ing brake will automatically be released and
the vehicLe will start moving. Important: The
driver's door must be closed.
Stopping/parking the car
If
you
open the driver's door while the selector
lever is not in position P, the vehicle can roll
away. The message Shift to P, otherwise vehicle
can roll away. Doors do not lock if lever is not in
P. appears on vehicles with convenience key*. A
buzzer will also sound.

•
Press and hold the brake pedal
<=>
A..

•
Apply the parking brake.

•
Move the selector Lever to P.
In some situations (such as on mountain roads or
when towing a trailer or caravan) it can be advan­
tageous to switch temporarily to the manual
shift programme so that the gear ratios can be
selected manually to suit the driving conditions

^>page
90.
On level ground it is sufficient to move the selec­
tor lever to P. On a gradient the parking brake
should be applied first and the selector Lever
should be moved to
P ^>page
82. This reduces
the load on the locking mechanism and makes it
easier to move the selector lever out of position
P. •
88

Driving
A WARNING
- The driver should never get out of the
vehi­

cle when the engine is running and a gear is

engaged.
If you have to leave your vehicle
while the engine is running, you must apply
the parking brake and engage the parking
lock P.
-If the engine is running and a gear is engag­
ed (D/S or R) or the vehicle is in "tiptronic"

mode,
you will need to hold the car with the
footbrake. Otherwise, the car will "creep"
forwards as the power transmission is not
fully interrupted even when the engine is

idling.

- The accelerator pedal must on no account
be pressed inadvertently when the vehicle is
stationary. The vehicle could otherwise start
moving immediately (in some cases even if
the parking brake is engaged) and possibly
cause an accident.
- Do not press the accelerator while selecting
a gear with the vehicle stationary and the
engine running, as this could cause an
acci­

dent.
- Never move the selector lever to R or P
when driving at normal speeds, as this could
cause an accident.
- Before you drive down a steep gradient, re­
duce the speed and use "tiptronic" to select
a low gear.
- Never allow the brake to drag when driving
downhill and do not use the brake pedal too
often
or
for long periods. Constant braking
will cause the brakes to overheat and will
considerably reduce the effectiveness of the
brakes. It will increase the braking distance
and could cause the brake system to
fail.

- To avoid rolling back on gradients always
hold the vehicLe with the footbrake or park­
ing brake if you have to stop.
- Never attempt to hold the vehicle with the
clutch when stopping on a gradient. The
clutch is disengaged automatically if it is
overloaded and becomes too hot - accident
risk! If the clutch is overloaded, the indica­
tor lamp
0
will light up and a message will
appear
^>page
92.
© CAUTION
- When you have stopped on a gradient, do
not try to stop the vehicle rolling back by ac­
celerating when a gear is engaged. This
could cause the automatic gearbox to over­
heat and become damaged. Apply the park­
ing brake or press the brake pedal in order
to prevent the vehicle from rolling back.
- If you allow the car to roll with the selector
lever in position N with the engine switched
off, the automatic gearbox will be damaged
as it will not be lubricated
^page
328,
Tow-starting / towing
away.

- In certain driving and traffic conditions, for
instance in stop-and-go traffic, if you have
to pull away frequently or if the vehicle
creeps forwards over a long distance, the
gearbox can overheat and become dam­

aged.
If the indicator Lamp
[5J
or the warn­
ing
lampH
Lights up, stop the vehicle at
the first opportunity and let the gearbox
cool down
^>page
92.
© Note
For safety reasons the parking brake will only
release automatically if the driver's door is

closed.

Downhill speed control
Applies to: vehicles with automatic gearbox
The downhill speed control function helps the
driver when driving down steep gradients.
Downhill speed control is activated on a downhill
gradient when the selector lever is in D/S and the
driver presses the brake pedal. The gearbox auto­
matically selects a suitable gear for the gradient.
The downhill speed control function attempts to
maintain the speed at which the vehicLe was trav­
elling when the foot brake was applied (subject
to the laws of physics and technical limitations of
the power train). It may be necessary to adjust
the speed again using the foot brake. The down­
hill speed control can change down to 3rd gear
but no further, so it may be necessary to change
to tiptronic mode on very steep gradients. In this

case,
change down manually to 2nd or 1st gear in •
CO
89

Driving
tiptronic mode to use the engine braking effect
and reduce the load on the brakes.
Downhill speed control is deactivated as soon as
the road Levels out again or you press the acceler­
ator pedal.
On vehicles with cruise control system*

<^>page
104, downhill speed control is activated
when you set
a
cruising speed.
A WARNING
The downhill speed control function cannot
defy the Laws of physics and may therefore
not be able to maintain a constant speed in
certain circumstances. Always be prepared to
use the brakes!
Manual gear selection (tiptronic mode)
Applies to: vehicles with automatic gearbox

The
tiptronic feature allows the driver to also
change gear manually.

Fig.
78 Centre console: Manual gear selection using selec­
tor lever

Fig.
79 Steering wheel: Manual gear selection with paddle
levers*
Gear selection with selector lever
The tiptronic mode can be selected either with
the vehicLe stationary or on the move.

•
From position D/S, push the selector lever to
the right into the tiptronic selector gate to
acti­

vate tiptronic mode. As soon as the automatic
gearbox has activated this mode, the letter M
will appear on the display
opage
86, Fig. 75;

e.g.
M4 means
that
the vehicle is in 4th gear.

•
Briefly push the selector lever forwards
0

oF/'g.
78 to change up a gear.

•
Briefly pull the selector lever back
Q
to change
down a gear.
Gear selection with paddle levers*
You can use the paddle levers when the selector
lever is in position D/S or M
(-
tiptronic selector

gate).

• To shift up a gear, briefly pull the paddle lever

Q*Fig.
79.

•
To shift down a gear, briefly pull the paddle lev­

er©.

If
you
use the paddle levers when the selector
lever is in positions D/S, the gearbox will remain
in manual mode for
a
while. To switch back im­
mediately to automatic mode after changing
gears manually,
pull
the paddle
lever 0

^>Fig.
79 for approximately 1 second.
If
you
want to use the paddle levers permanent­
ly, push the selector lever from position D/S to
the right into the tiptronic selector gate.
Description
The gearbox automatically shifts up or down into
the next gear before a critical engine speed is

reached.

The gearbox only allows manual gear changes if
the engine speed would remain within the per­
missible range.
Kick-down feature
Applies to: vehicles with automatic gearbox

The
kick-down feature is designed to give maxi­
mum acceleration.
When the accelerator pedal is pressed right down
past the point of resistance at full throttle (kick-
down feature), the gearbox
wilL
shift down to a
lower gear, depending on road speed and engine •
90

Driving

•
Briefly pull the selector lever back from
posi­

tion D/S to select position S, or move the selec­
tor lever to the right into the tiptronic gate, or
select dynamic mode in drive select*

^>page
131.

•
Press the brake pedal firmly with your
left
foot
and hold it down for at Least one second.

•
At the same time, press the accelerator all the
way down with your right foot until the engine
revs are high and steady.
• Take your
left
foot
off
the brake.
A WARNING
- Always adapt your driving style to the traffic
conditions.
- Only use the launch control programme
when road and traffic conditions permit,
and make
sure
your manner of driving and
accelerating the vehicle does not inconven­
ience or endanger other road users.
- Please note that the driven wheels may
start to spin when the off-road mode is
switched on, causing the vehicle to Lose

grip,
in particular on slippery or wet roads -
danger of skidding!
- When acceleration has been completed, you
should deactivate the off-road mode again
by briefly pressing the
|flQFF|
button.
© Note
- The gearbox may be hot after you have used
the launch control programme. In this case,
the programme may not be available for
several minutes. The programme will be
available again after
a
cool-down period.
-Accelerating with the launch control pro­
gramme places a heavy load on all parts of
the vehicLe. This can result in increased wear
and tear.
Gearbox malfunction
Applies to: vehicles with automatic gearbox
| Gearbox malfunction! Please stop the vehi­
cle and select P
There is a malfunction in the gearbox. Park the
vehicle safely and do not drive on. Obtain profes­
sional assistance.
| Gearbox overheating! Please stop the vehi­

cle.

The gearbox is overheating and could be dam­

aged.
Stop the vehicle and let the gearbox cool
down with the engine idling and the selector lev­
er in position P. If the warning lamp and the
message disappear, drive to a qualified workshop
soon and have the fault rectified. Do not drive on
if the warning lamp stays on and the message
does not disappear. Obtain professional assis­

tance.

E3
Gearbox malfunction: you can continue driv­
ing
Drive to a qualified workshop soon and have the
fault rectified.

S3
Gearbox malfunction: no reverse gear (you
can continue driving)
A gearbox malfunction has occurred. The gearbox
will switch to the back-up programme. The pro­
gramme will only move into certain gears or may
not be able to shift gears at all. The engine may

stall.
You can no longer engage reverse gear.
Drive to a qualified workshop without delay and
have the fault rectified.

jftj
Gearbox malfunction: you can continue driv­
ing in D until engine off
Park your vehicle well away from moving traffic.
Obtain professional assistance.

ty
Gearbox overheating: please adapt driving
style
You can continue driving at moderate speed. You
can resume normal driving if the indicator lamp
goes out.

LQ]
Gearbox: please press brake pedal and select
gear again
If
a
gearbox malfunction has occurred due to
overheating, this message will appear once the
gearbox has cooled down again.
92

Driving

CO

< o rN
iv
rN
i—i

00
Releasing the selector lever manually (left-
hand drive vehicles)
Applies to: vehicles with automatic gearbox

The
selector lever can be released manually if
the electrical power supply should
fail.

K

Fig.
80 Selector lever: Removing the boot

Fig.
81 Manually releasing the selector lever from position
P
This section describes how to manually release
the selector Lever on Left-hand drive vehicles.
The selector lever must be manually released
from position
P
in order to move or tow the
vehi­

cle.

The manual release mechanism is Located on the
right underneath the selector gate. Releasing the
selector lever requires a certain degree of practi­
cal
skill.
We therefore advise you to obtain pro­
fessional assistance.
To release the selector lever, you
wilL
need the
screwdriver from the vehicle's tool kit, which is
located in the luggage compartment

^>page
319. Use the flat-blade side of the rever­
sible screwdriver insert.
Removing the selector lever boot
• Apply the parking brake
& ^/^
to prevent
your vehicle from moving. If this is not possi­

ble,
use other means to prevent your vehicle
from moving.

•
Switch off the ignition.
• To loosen the selector lever boot, carefully in­
sert the flat-blade side of the screwdriver into
the opening
at
the side of the boot
^>Fig.
80.

•
Carefully lever off the boot with the screwdriver

and,
at the same time, pull the boot upwards
-arrow- at the crease with your hand until it is
released at all four corners.

•
Fold the boot over the selector lever knob

=>
Fig.
81.
Releasing the selector lever manually

•
Insert the screwdriver in the opening for the
yellow release lever
^>Fig.
81.

•
Using the screwdriver, carefully pull the release
lever towards the rear as far as it will go and
hold it in this position.

•
Now press the interlock button on the selector
lever
®
and move the selector lever to position
N.

•
After manually releasing the selector lever
make sure you clip the gear lever boot back into
the gearshift gate.
A WARNING
- Only use the manual release mechanism
when the vehicle is on level ground or a
slight gradient.
- The selector lever must not be moved out of
position
P
if the parking brake is not ap­

plied.
If this does not work, use the brake
pedal to hold the vehicle or use wheel
chocks or similar to block one of the front
and rear wheels. If
you
do not apply the

brake,
the vehicle may roll away and cause
an accident.
93

Driving
Releasing the selector lever manually
(right-hand drive vehicles)
Applies to: vehicles with automatic gearbox

The
selector lever can be released manually if
the electrical power supply should
fail.

n

Fig.
82 Selector lever: Removing the boot

m

i

Fig.
83 Manually releasing the selector lever from position
P
This section describes how to manually release
the selector lever on right-hand drive vehicles.
The selector lever must be manually released
from position
P
in order to move or tow the
vehi­

cle.

The manual release mechanism is located on the
right underneath the selector gate. Releasing the
selector lever requires a certain degree of practi­
cal
skill.
We therefore advise you to obtain pro­
fessional assistance.
To release the selector lever, you will need the
screwdriver from the vehicle's tool kit, which is
located in the luggage compartment

^>page
319. Use the flat-blade side of the rever­
sible screwdriver insert.
Removing the selector lever boot

•
Apply the parking brake fâ)
o^
to prevent
your vehicLe from moving. If this is not possi­

ble,
use other means to prevent your vehicle
from moving.

•
Switch off the ignition.
• To Loosen the selector lever boot, carefully in­
sert the flat-blade side of the screwdriver into
the opening
at
the side of the boot
^>Fig.
82.

*•
Carefully lever off the
boot
with the screwdriver

and,
at the same time, pull the boot upwards
-arrow- at the crease with your hand until it is
released at
alL
four corners.

•
Fold the boot over the selector lever knob

^Fig.
83.

•
Take out the panel for the selector Lever
posi­

tion indicator and Let it hang down to one side,
suspended by the cable
0 •=>
Fig.
83.
Releasing the selector lever manually

•
Insert the screwdriver in the opening for the
yellow release lever (section
@
of
<$
Fig.
83).

•
Using the screwdriver, carefully pull the release
lever towards the rear as far as it will go and
hold it in this position.

•
Now press the interlock button on the selector
lever
@
and move the selector Lever to position
N.

•
After manually releasing the selector lever,
make sure you fit the panel for the selector lev­
er position indicator back in the selector gate
and clip the selector lever boot back into place.
A WARNING
- Only use the manual release mechanism
when the vehicle is on level ground or a
slight gradient.
94

Driver assist systems

CO

< o rN
iv
rN
•-i

00
sections, please temporarily switch off the
cruise control system.
- Make sure you do not unintentionally rest
your foot on the accelerator - this will over­
ride the cruise control system which, as a re­
sult, will not brake the vehicLe.
-The automatic braking function may be de­
activated if
a
system fault occurs in the
brake system (e.g. if the brakes overheat)
while the cruise control system is activated.
All the other cruise control functions remain
activated as long as the indicator lamp
^
is
lit.
Before driving down a
long,
steep gradient, it
is advisable to reduce speed and select a low­
er gear. In this way you will make use of the
engine braking effect and relieve the Load on
the brakes.
© Note
- Applies to vehicles with manual gearbox:
The set speed cannot be reached if the cur­
rently selected gear is too high or too low or
if the engine would
overrevorfailto
run
smoothly at the target speed. Make sure to
change up or down a gear in good time.
- The brake lights come on when the system
brakes the vehicle.
Setting a new speed
Applies to: vehicles with cruise control system
• Briefly push the Lever towards
©/®

^>page
104, Fig. 94 to increase or reduce the
cruising speed in small steps.

•
To increase or reduce the speed quickly, hold
the lever towards
©/®
until you reach the de­
sired cruising speed.
Overriding the set speed
Applies to: vehicles with cruise control system
You can use the accelerator pedal to increase
speed in the normal way, for example to overtake
another vehicle. Once you release the accelera­
tor, the system will revert to the speed you stor­
ed initially.
However, if the vehicLe exceeds the programmed
speed significantly for
a
long time, the cruise
control system will be deactivated temporarily.
The indicator lamp
El
in the instrument cluster
will go out, but the programmed speed will re­
main stored.

Pre-selecting
a speed
Applies to: vehicles with cruise control system

You
can preselect a desired speed while the ve­
hicle is stationary.

•
Switch on the ignition.

•
Pull the lever to position
® ^>page
104,
Fig. 94.
• Press the lever up towards © or down towards

0
in order to increase or reduce the cruising
speed setting.
This function allows you to enter the desired
cruise control setting speed ahead of
time,
for
example before joining a motorway.
Once
you are
on the motorway, you can activate the cruise
con­

trol system by pulling the lever to position ®.
Switching off
Applies to: vehicles with cruise control system
Switching off temporarily

•
Press the brake pedal, or

•
Push the lever to position @ (click stop not en­
gaged)
^>page
104, Fig. 94, or
Switching off completely

*•
Push the lever to position
©
(click stop engag­

ed),
or

•
Switch off the ignition.
The speed setting will remain stored after the
system is temporarily deactivated. To resume the
programmed cruising speed, release the brake
pedal and pull the lever to position ®.
The stored speed will be deleted once the
igni­

tion is switched off. •
105