2021 AUDI Q2 clock

Mobility

\J Note

Note the code number of the anti-theft wheel
bolt and keep it in a safe place - not in your
vehicle. If
you
need a replacement adapter,
give the code number to your Audi dealer.
Loosening the wheel bolts
Raising the vehicle

Fig.
261 Wheel: Loosening the wheel bolts
•
Fit
the box spanner (provided in the vehicle's
tool kit) as far as it will go over the wheeL
bolt1'.
• Turn the wheel bolt approx. one turn
anti­

clockwise -arrow-. To apply the necessary tor­

que,
hold the box spanner
near
the end. If the
wheel bolt is very tight, you may be able to
loosen it by pushing down the end of the span­
ner carefully with your foot. Hold on to the car
for support and take care not to slip.
WARNING
To avoid accidents, the wheel bolts should on­
ly be loosened slightly (one turn) before rais­
ing the vehicle with the jack*.

:v<
:

Fig.
262 Sills: markings (example)

Fig.
263 Door
sill:
Applying the jack under the door sill
• Always provide a firm base for the jack* on the

ground.
(The jack can be found in the vehicle's
tool kit). If necessary use a large, strong board
or similar support. On a
hard,
slippery surface
(such as tiles) use a rubber mat or similar to
prevent
the
jack from slipping
^> /\.

• Locate the marking (recess or rib) on the door
sill closest to the wheel being changed

^>Fig.
262. The jacking point is located behind
the marking under the door
sill.

• Wind up
the
jack* under
the
jacking point until
the claw
(A)
•=>
Fig.
263 of the jack is directly
be­

low the jacking point.
• Align
the
jack* so
that
the
claw
(A)
grips the
jacking point under the door sill and the mova­
ble base plate of the jack
(B)
is flat on the

ground.
The base plate
(B)
must be positioned
vertically underneath
the
jacking point®.
• Raise the vehicle until the defective wheel is
clear of the ground.

11
An adapter is required to unscrew or tighten the anti-theft
wheel bolts
opage
321.
322

Mobility

CO

rN
IV
rN
•-i

00
Removing the spare wheel
• Lift the floor panel up by the plastic handle un­
til the panel is fixed in position behind the re­
taining tabs on the two side sections
©
*
Fig.
266.
• Applies to vehicles with bass box in spare wheel

well:
Remove the bass box*. Please first check
the connector to establish which bass box is fit­
ted in your vehicle: version 1)
*page
325 or
version 2)
*page
326.
• Turn the plastic knob anti-clockwise.
• Take out the spare wheel.
Snow chains
For technical reasons, snow chains must not be
used on the compact temporary spare wheel.
Should you have a puncture on one of the front
wheels when using snow chains, fit the compact
temporary spare wheel in place of one of the rear
wheels. You can then attach the snow chains to
the wheel taken from the rear and use this wheel
to replace the punctured front wheel.
A WARNING
- The tyre pressure must be checked as soon
as possible after fitting the spare wheel - an
incorrectly inflated tyre can increase the risk
of accident. You can find the tyre pressures
here
*page
307, Fig. 253.
- Do not drive faster than 80 km/h when the
compact temporary spare wheel is fitted -
higher speeds can cause an accident.
-Avoid heavy acceleration, hard braking and
fast cornering when the compact temporary
spare wheel is fitted - risk of accident!
- Never use two or more compact spare tyres
at the same time - risk of accident!
- No other type of tyre (normal summer or
winter tyres) may be fitted on the compact
temporary spare wheel.
Removing the bass box (version 1)
Applies to: vehicles with bass box in spare wheel well

You
must remove the bass box before you can
take out the spare wheel*.

«

Fig.
268 Spare wheel
well:
Bass box
Removing the bass box
• Lift the floor panel
<=>page
324, Fig. 266.
• Compress the retaining
tabs©*Fig.
268 on
the connector.
• Unplug the connector © and move the discon­
nected cable clear to one side.
• Unscrew
bolt©.

• Carefully take out the bass box.
Installing the bass box
• Carefully place the bass box in the well of the

rim.
Make sure that the inscription "FRONT" on
the bass box points to the front of the vehicle.
• Plug the connector back in again.
• Secure the bass box with the screw.
• Fold the floor panel back down.

(T) Note

The bass box can be fitted even if there is no
wheel in the spare wheel
well.

325

Fuses and bulbs
You must only replace a bulb with a bulb of the
same type. Information regarding e.g. the wat­
tage can be found on the glass or base of the

bulb.

The description for changing the bulb refers to
the Left rear light unit; the procedure for the
right rear Light unit is similar.
You can change the
foLLowing
bulbs yourself:
Changing bulb for turn signals
Applies to: vehicles with halogen headlights
Bulb (12 V)

©Tail
light
© Brake light
© Reversing Light

(4)
Turn signal

©Rearfog
light3'

Version
W16W
P21W
W16W
PY21W
W16W

a'
The bulb for the rear fog light is fitted on one side only. It
is located on the left side on LHD vehicles and on the right
side on RHD vehicles.
Changing headlight
bulbs
Removing cover (engine compartment)
Applies to: vehicles with halogen headlights

^

Fig.
281 Headlight: Cover for turn signal and main beam
headlight
• Switch off the ignition and the lights.
• Open the bonnet.
• Turn the headlight cover anti-clockwise

*Fig.
281 and remove it
*/^
in General notes
on page 334.
• Change the bulb for the turn signal

*page
336 or the main beam headlight

*page
337.

Fig.
282 Headlight: Plastic connector for turn signal

Fig.
283 Headlight: Fitting plastic connector for turn
sig­

nal
Removing
• Pull the plastic connector together with the
buLb out of the headlight housing
*Fig.
282.
• Disconnect the plastic connector from the base
of the bulb
*^
in General notes on page 334.
Installing
• Push the new bulb into the plastic connector so
that it is securely seated
*^
in General notes
on page 334.
• Insert the bulb into the headlight housing.
•
Fit
the plastic connector
*Fig.
283 into the
housing and press it in until the side catches
engage.
• Put the cover back on.
• Check whether the new bulb is working.
336