2021 AUDI Q2 side panel

Mobility
Tool kit/tyre repair kit/compressor Using the tyre repair kit
Applies to: vehicles with tool kit/tyre repair kit/compressor Applies to: vehicles with tyre repair kit

CO

rN
IV
rN
•-i

00

Fig.
256 Luggage compartment (example): Floor panel
folded up
The tools, tyre repair kit* and compressor* are
stored under the floor in the luggage compart­
ment.

•
Lift up the floor panel until it is fixed in position
behind the retaining tabs
©
on the two side
sections.

•
Replace the floor panel before closing the boot

lid.

(T)
Note
The jack* in your vehicle is maintenance-free.
Tyre repair kit
Preparations
Applies to: vehicles with tyre repair kit

•
Please refer to the important safety notes on

•=>
page 318.

•
Apply the parking brake.

•
Manual gearbox: Engage first gear.
• Automatic gearbox: Move the selector lever to
position P.

•
Check whether
a
repair is possible using the
tyre repair kit
^page
319.

Fig.
257 Tyres: Irreparable tyre damage
Repaired tyres are only suitable for temporary

use.
Replace the damaged tyre as quickly as pos­
sible
°=>A-

If the tyre was damaged by an object, such as a

nail,
do not remove it from the tyre.
The tyre repair kit can be used at outside temper­
atures down to - 20 °C.
The tyre repair kit must NOT be used:
- On cuts and punctures larger than 4 mm
©

^Fig.
257.
- If the wheel rim has been damaged ©.
- If
you
have been driving with very low pressure

or a
completely flat
tyre(|).

In these cases, you should seek professional as­
sistance.

A
WARNING
- Please note that the tyre repair kit is not
suitable for use in every situation and
should only be used as a temporary meas­

ure.

- Do not allow the sealant to come into
con­

tact with your eyes, skin or clothing.
- If
you
do come into contact with the sealant
immediately rinse the eyes or skin affected
with clean water.
- Make sure you do not breathe in the fumes.
- If
you
accidentally swallow tyre sealant, im­
mediately rinse your mouth thoroughly and
drink
a
large amount of water. Do not in­
duce vomiting. Immediately contact
a
doc­
tor.
319

Mobility
not possible to tighten the bolts to the re­
quired torque using the hexagonal socket

risk
of accident!
© CAUTION
When removing/fitting the wheel the rim
may hit and damage the brake disc. For this

reason,
please take care and get
a
second per­
son to assist you.

(T) Note

The wheel bolts are easier to remove from the
wheel rim if
you
use the hexagonal socket in
the screwdriver handle. The reversible screw­
driver blade should be removed as a precau­
tionary measure when the tool is used for this
purpose.
Tyres with directional tread pattern
A directional tread pattern can be identified by
arrows on the sidewall that point in the direction
of rotation. Always note the direction of rotation
indicated when mounting the wheel. This is im­
portant so that these tyres can give maximum
grip and avoid excessive noise, tread wear and
aquaplaning.
If
you
ever have a puncture and need to fit the
spare wheel* in the wrong direction, please drive
with extra care because the tyre will not give op­
timum performance in this situation. Bear this in
mind particularly when driving on wet roads.
To benefit from the advantages of tyres with this
type of tread pattern, the defective tyre should
be replaced and refitted as soon as possible so
that all tyres again rotate in the correct direction.
After changing a wheel
• Fit the hubcap or wheel bolt caps back on, as

required.

• Put the tools and jack back in the luggage com­
partment.
• If the replaced wheel will not fit into the spare
wheel
well,
stow it safely in the luggage com­
partment
*page
272.
• Check the tyre pressure of the fitted wheel as
soon as possible.
• On vehicles with tyre pressure loss indicator,
adjust the tyre pressures and store them via the
infotainment system
opage
311.
• The wheel bolts should be tightened to 140

Nm.
Have this checked as soon as possibLe with
a torque wrench. Until
then,
drive with caution.
• Have the flat tyre replaced as quickly as possi­

ble.

Spare wheel
General notes
Applies to: vehicles with compact temporary spare wheel

Fig.
266 Luggage compartment: Floor panel folded up

Fig.
267 Compact temporary spare wheel (example)
The compact temporary spare wheel
*Fig.
267 is
only intended for temporary use over short dis­
tances. Have the damaged wheel checked as soon
as possible by
a
qualified workshop and, if neces­
sary, replaced.
PLease note the following restrictions when using
the compact temporary spare wheel. The com­
pact temporary spare wheel is designed specifi­
cally for this model. For this reason, do not use a
spare wheel from a different type of
vehicle.
•
324

Mobility

CO

rN
IV
rN
•-i

00
Removing the spare wheel
• Lift the floor panel up by the plastic handle un­
til the panel is fixed in position behind the re­
taining tabs on the two side sections
©
*
Fig.
266.
• Applies to vehicles with bass box in spare wheel

well:
Remove the bass box*. Please first check
the connector to establish which bass box is fit­
ted in your vehicle: version 1)
*page
325 or
version 2)
*page
326.
• Turn the plastic knob anti-clockwise.
• Take out the spare wheel.
Snow chains
For technical reasons, snow chains must not be
used on the compact temporary spare wheel.
Should you have a puncture on one of the front
wheels when using snow chains, fit the compact
temporary spare wheel in place of one of the rear
wheels. You can then attach the snow chains to
the wheel taken from the rear and use this wheel
to replace the punctured front wheel.
A WARNING
- The tyre pressure must be checked as soon
as possible after fitting the spare wheel - an
incorrectly inflated tyre can increase the risk
of accident. You can find the tyre pressures
here
*page
307, Fig. 253.
- Do not drive faster than 80 km/h when the
compact temporary spare wheel is fitted -
higher speeds can cause an accident.
-Avoid heavy acceleration, hard braking and
fast cornering when the compact temporary
spare wheel is fitted - risk of accident!
- Never use two or more compact spare tyres
at the same time - risk of accident!
- No other type of tyre (normal summer or
winter tyres) may be fitted on the compact
temporary spare wheel.
Removing the bass box (version 1)
Applies to: vehicles with bass box in spare wheel well

You
must remove the bass box before you can
take out the spare wheel*.

«

Fig.
268 Spare wheel
well:
Bass box
Removing the bass box
• Lift the floor panel
<=>page
324, Fig. 266.
• Compress the retaining
tabs©*Fig.
268 on
the connector.
• Unplug the connector © and move the discon­
nected cable clear to one side.
• Unscrew
bolt©.

• Carefully take out the bass box.
Installing the bass box
• Carefully place the bass box in the well of the

rim.
Make sure that the inscription "FRONT" on
the bass box points to the front of the vehicle.
• Plug the connector back in again.
• Secure the bass box with the screw.
• Fold the floor panel back down.

(T) Note

The bass box can be fitted even if there is no
wheel in the spare wheel
well.

325

Mobility
Removing the bass box (version 2)
Applies to: vehicles with bass box in spare wheel well

You
must remove the bass box before you can
take out the spare wheel*.
f

Fig.
269 Spare wheel
well:
Bass box
Removing the bass box
• Lift the floor panel
*page
324, Fig. 266.
•
Pull
the
catch
Q^F/g.
269 towards the cable.
• Press the retaining tab © down.
• Unplug the connector © and move the discon­
nected cable clear to one side.
• Unscrew
bolt
(4).
• Carefully take out the bass box.
Installing the bass box
• Carefully place the bass box in the well of the

rim.
Make sure that the inscription "FRONT" on
the bass box points to the front of the vehicle.
• Plug the connector back in again.
• Push the catch © back towards the bass box.
• Secure the bass box with the screw.
• Fold the floor panel back down.
Note
The bass box can be fitted even if there is no
wheel in the spare wheel
welL.

Jump-starting
Before starting the engine
If
necessary,
the engine can be started by con­
necting it to the battery of another vehicle.
If the engine fails to start because of
a
dis­
charged battery, the vehicle battery can be
con­

nected to the battery of another vehicle to start
the engine. Suitable jump leads are required.
Both vehicle batteries must be rated at 12 V. The
capacity (Ah) of the booster battery should not
be significantly lower than that of the discharged
battery.
Jump leads
The jump Leads must be heavy enough to carry
the starter current. Refer to the details given by
the manufacturer.
Only
use
jump leads with insulated battery
clamps.
Positive cable - usually red.
Negative cable - usually black.
WARNING
- When it is discharged the vehicle battery
can freeze at temperatures around 0°C. A
frozen vehicle battery must first be thawed
out before connecting the jump leads - risk
of explosion and chemical burns! After
jump-starting the vehicle, drive to a quali­
fied workshop without delay and have the
vehicle battery checked.
- The engine compartment is a potentially
hazardous area and working here can lead
to serious injuries. Before carrying out any
work in the engine compartment please
read and observe the warnings
*page
295.
- Incorrect handling of the jump leads may
result in the vehicLe battery exploding (risk
of serious injury). Please observe the follow­
ing rules to minimise the risk of injury:
- The non-insulated parts of the battery
clamps must not be allowed to touch. The
jump lead attached to the positive terminal
must not touch metal parts of the vehicle:
this can cause short circuiting.
- Position the jump leads in such a way that
they cannot come into contact with any
moving parts in the engine compartment.
- Do not lean over the vehicle battery - risk of
chemical burns!
- The screw plugs on the battery cells must be
screwed in firmly.
326

Fuses
and
bulbs

CO

rN
IV
rN
•-i

00
Changing bulbs
for
rear
Lights
Preparations

Applies
to: vehicles with bulbs
Changing
a
bulb

Applies
to: vehicles with bulbs

Fig.
292
Side
panel:
Removing cover

Fig.
293
Removing rear light from body panel
• Check which
of
the bulbs
is
defective.
• Switch
off
the ignition and
the
lights.
• Open
the
boot lid.
• Take
the
screwdriver,
the
interchangeable Torx
bit and
the
removal wedge
out of
the vehicle
tool
kit
*page
319.

• To remove
the
cover, press
it in the
direction
of

the arrow
©
*
Fig.
292
and then swivel
it
away
to
the
side with your hand
©.

• Remove the securing screws
©
using
the
Torx
screwdriver.
• Carefully slide
the
removal wedge
©
into
the

gap between
the
body and
the
rear light

•=>
Fig.
293,
o©
in
General notes on page
335.

• Gradually ease out the rear light
by
pulling
al­

ternately
in
direction
of
arrows
©
and
©.

• Unplug
the
electrical connector.
• Change the defective bulb
*page
339.

1
u
f"

00

o

00 m
Fig.
294 Rear light: Release points on bulb carrier

^

®-g

Fig.
295
Bulbcarr

4B
&fï|
STPJ

ml
»Wm

er: Position

sio^

P*^^^HP^

of the bulbs

O)
CO
o

OQ

• Remove the clips securing
the
bulb carrier

*Fig.
294.
Start with
the
three clips
at
the bot­
tom -arrows-.
• Detach
the
bulb carrier
*Fig.
295.

• Renew the defective bulb (pull
to
remove from
plug-in holder
or
turn
to
remove from bayonet
holder).
• Attach
the
bulb carrier.
• Re-install all the parts
in the
reverse sequence.
• Check whether the new bulb
is
working.
Position
of
bulbs
Position

*
Fig.
295

®
®

(D

©
®
Bulb function
Tail light
Brake light
Reversing Light
Turn signal

Rear
fog light
339