2021 AUDI Q2 mode

Driving
Driving
General notes
Running in
A new vehicle should be run in over
a
distance of
1,500 km. For the first 1,000 km the engine
speed should not exceed 2/3 of the maximum
permissible engine speed - do not use full throt­
tle and do not tow a trailer or caravan. From
1,000 to 1,500 km you can gradually increase
the engine rpm and road speed.
During its first few hours of running, the internal
friction in the engine is greater than later on
when all the moving parts have bedded down.
How the vehicle is driven for the first 1,500 km
also influences the engine quality. After this
peri­

od you should continue driving at moderate en­
gine speeds, in particular when the engine is

cold.
This helps to reduce wear and tear on the
engine and increases the potential mileage which
can be covered by the engine.
You should also avoid driving with the engine
speed too low. Change down to a lower gear
when the engine no longer runs "smoothly". Ex­
cessively high engine speeds are prevented by an
automatic rev limiter.
A WARNING
After driving through water, mud, sludge,
etc., the braking effect can be delayed slightly
due to moisture on the discs and brake pads.
Applying the brakes carefully several times
will remove the moisture and restore the full
braking effect.
© CAUTION
- Parts of the vehicle (e.g. engine, gearbox,
running gear or electrical components) can
be badly damaged when driving through
water.
- Always switch off the start/stop system*

^>page
79 before driving through water.
© ' Note
- It is advisable to check the depth at the
deepest point before approaching the wa­
ter.
- Do NOT stop the vehicle, drive in reverse or
switch off the engine before you are out of
the water.
- Bear in mind that waves created by oncom­
ing traffic could exceed the permissible
wading depth of your vehicle.
- Avoid driving through salt water (corrosion).
Avoiding damage to the car
© CAUTION
Take care not to damage
Low-mounted
parts
of the car (such as the spoiler or exhaust sys­
tem) on steep ramps, uneven road surfaces or
roadside kerbs, etc. This applies especially to
vehicles with low ground clearance and to all
vehicles when fully laden.
Driving through water on roads
Please note the following in order to prevent
damage to the vehicle when driving through wa­
ter (e.g. on flooded roads):
- The water level must not be higher than the ve­
hicle's underbody.
- Do not drive faster than walking pace.
How to improve economy and minimise
pollution
Fuel economy, environmental impact and wear
on the engine, brakes and tyres depend largely
on the way you drive the vehicle. By adopting an
economical driving style and anticipating the
traffic situation ahead, you can reduce fuel
con­

sumption by 10
-15
%. The following section
gives you some tips on Lessening the impact on
the environment and reducing your operating
costs at the same time.
Anticipate well in advance
A car uses most fuel when accelerating. If
you
an­
ticipate hazards and speed changes well in ad­

vance,
you will need to brake less and thus accel­
erate Less. Wherever possible, Let the car slow
down gradually with a gear engaged, for •
72

Driving
instance when you can see that the next traffic
lights are red. This takes advantage of the engine
braking effect, reducing wear on the brakes and

tyres.
Emissions and fuel consumption will drop
to zero due to the overrun fuel cut-off.
Change gear early to save fuel
An effective way of saving fuel is to change up
quickly through the gears. Running the engine at
high rpm in the lower gears uses an unnecessary
amount of
fuel.

Applies to: vehicles with manual gearbox
Shift up to second gear as soon as possible. If
possible, we recommend shifting up to the next
gear at approx. 2,000 rpm.
Applies to: vehicles with automatic gearbox
Press the accelerator slowly and avoid using the

"kick-down"
feature.
Avoid driving at high speed
Avoid travelling at top speed. Fuel consumption,
exhaust emissions and noise Levels all increase
very rapidly at higher speeds. Driving at moder­
ate speeds will help to save
fuel.

Do not let the engine idle for longer than
necessary
Engine idling periods are automatically reduced
on vehicles with start/stop system*. On vehicles
without a start/stop system, it is worthwhile
switching off the engine at level crossings, for in­
stance, or at traffic lights with a long red phase.
The fuel saved after about 5 seconds can be
greater than the amount of fuel needed to re­
start a warm engine (the exact fuel saving de­
pends on the engine version).
The engine takes a very long time to warm up
when it is running at idling speed. Mechanical
wear and pollutant emissions are also especially
high during this initial warm-up phase. It is
therefore best to drive off immediately after
starting the engine. Avoid running the engine at
high speed.

o
Regular servicing
Regular servicing can establish a basis for good

iS
fuel economy before you start driving. A
well-

serviced engine gives you the benefit of im­
proved fuel efficiency as well as maximum relia­
bility and an enhanced resale value. A poorly
maintained engine can consume up to ten per­
cent more fuel than necessary.
Avoid short trips
The engine and emission control system need to
reach their proper working temperature in order
to minimise fuel consumption and emissions.
A cold engine uses disproportionately more
fuel.

The engine only reaches its working temperature
after about four kilometres, when fuel consump­
tion will return to a normal level.
Check tyre pressures
Always make sure the tyres are inflated to the
correct pressures
•=>page
306 to save
fuel.
If the
tyre pressures
are
just 0.5
bar
too Low, this can
increase the fuel consumption by as much as 5
%. Due to the greater rolling resistance, under-
inflation also increases tyre wear and impairs

handling.

Do not use winter tyres all through the year; they
will increase fuel consumption by up to 10 %.
Avoid carrying unnecessary loads
Every kilo of extra weight will increase the fuel
consumption, so it is worth checking the Luggage
compartment occasionally to make sure that no
unnecessary loads are being transported.
The roof carrier increases the air resistance of the
vehicle and should be removed when not in use.
This will save about 12 % of fuel at speeds of be­
tween 60 and 75
mph.

Save electrical energy
The engine drives the alternator to generate elec­
tricity. This means that fuel consumption rises
when more power is required for electrical equip­
ment. Switch off electrical equipment when it is
not needed. Electrical equipment which uses a
lot of electricity includes the blower (at a high
setting), the rear window heating and the seat

heating*.

73

Driving

CO

<
O
rN
IV
rN
t-H
o <
Starting the engine after
a malfunction

Applies
to: vehicles with convenience key
If the remote control key battery is exhausted or
if radio interference
or
a system malfunction oc­
curs, extra steps may be necessary in order to
start the engine.

Fig.
71 Steering column/remote control key: Starting the

engine
after a malfunction
If the message
D
Key not recognised. See
own­

er's manual or
|3
Remote control key: hold
back of key against marked area. See owner's
manual is displayed, you can still start the en­
gine manually.

•
Manual gearbox: Press the clutch
pedal

• Automatic gearbox: Press the brake pedal.

•
Hold the remote control key against the symbol

fJ)
^>Fig.
71, as shown in the illustration.
• Press the ISTART ENGINE
STOPl
button
^ A in

Starting the engine on page 76. The engine
shouLd start.

•
Drive to a qualified workshop soon and have the
fault rectified.
Note
You can call up the driver message again by
pressing the ISTART ENGINE STOP| button.
Start/stop system
Description

Applies
to: vehicles with start/stop system
The start/stop system can help to save fuel and
reduce
CO2
emissions.

1)
May vary in different countries
In start/stop mode, the engine is switched off
automatically when the vehicle stops, e.g. at
traffic lights. The ignition remains on during this
stop phase. The engine is automatically started
on demand.
The start/stop system is automatically activated
each
time
you switch on the ignition.
Basic conditions for start/stop mode
- The driver's door must be closed.
- The driver's seat belt must be buckled.
- The bonnet must be closed.
- The vehicle must have been moving at over 3
km/h since the Last stop.
CAUTION
Always switch off the start/stop system

^>page
81 before driving through water.
©
The engine is switched
off1)
shortly before the
vehicle comes to a stop. However, the brake
servo and power steering remain fully opera­

tional.

Stopping/starting the engine

Applies
to: vehicles with start/stop system

START
(M
STOP

S

Fig.
72 Instrument cluster: Engine switched off (stop

phase)

Applies
to: vehicles with manual gearbox

•
When the vehicle stops, put the gear Lever in
neutral and
take your
foot
off
the clutch pedal.
The engine will switch off. An indicator lamp

I
will light up in the instrument cluster •
79

Driving
display.
The rev
counter needle will also move

to
the
READY position.

•
The engine will start again automatically when
you press
the
clutch pedal.
The
indicator lamp
will
go out.

Applies to: vehicles with automatic gearbox

•
Brake
the
vehicle
to a
stop.
The
engine will
be

switched
off
shortly before
the
vehicle comes
to
a
standstill
or
when
the
vehicle
is
station-

aryx).
Keep your foot
on the
brake pedal.
The

indicator
lamp
@/
@
will appear
on the
dis­
play.
The rev
counter needle will also move
to

the READY position.

•
The engine will start again automatically when
you take your foot
off
the brake pedal.
If the

parking brake
is
applied
or
hold assist*
is

switched on,
the
engine will only restart when
you press
the
accelerator pedal1).
The
indicator
lamp
will
go out.

Further information
for
automatic gearboxes
The engine will stop
if
the selector lever
is in po­

sition
P, N or D.

The engine will start again
if
you move
the
selec­
tor lever
to
R during
a
stop phase.
If you
do not
want
the
engine
to
start when mov­
ing
the
selector Lever through
R,
move
the
lever
to P quickly.
You
can
control whether
or not the
engine
is

switched
off by
varying
the
amount
of
pressure
on
the
brake pedal.
For
instance,
if
you brake
gently
in
stop-and-go traffic
or
before turning
off

at a junction,
the
engine will remain
on
while
the

vehicle
is at
a standstill.
As
soon as you press
the

brake pedal harder,
the
engine will
be
switched

off.

be switched
off. The rev
counter needle will
move
to the
OFF position.
- Keep your foot
on the
brake pedal during
a

stop phase
to
prevent
the
vehicle from mov­

ing.

-
If you press the
ISTART ENGINE STOP|
but­

ton*
during
a
stop phase,
the
ignition will
Note
Applies to: vehicles with manual gearbox
If the engine stalls, you
can
start
it
again
di­

rectly
by
pressing
the
clutch pedal immedi­
ately.
General notes
Applies to: vehicles with start/stop system
Engine does
not
switch
off

The system checks that certain conditions
are

met before
and
during each stop phase.
If
the
in­

dicator lamp
Ey
appears
on the
instrument clus­
ter display,
the
engine will
not be
switched
off in

the following situations:
- The engine
has
not
yet
reached
the
minimum
temperature required
for
start/stop mode.
- The interior temperature selected
on the air

conditioner*
has
not
yet
been reached.
- The exterior temperature
is
very high/low.
- The windscreen
is
being defrosted
W.

-The parking
aid*
is
switched
on.

- The vehicle battery charge
is too low.

- The steering wheel
is
close
to
full lock
or the

vehicle
is
being steered.
- Reverse gear has just been selected.
- The vehicle
is on a
steep gradient.
-At high altitudes.
Engine cuts
in
again automatically
The stop phase
is
interrupted
in the
following sit­
uations,
for
example.
The
engine cuts
in
auto­
matically without intervention from
the
driver.
- The vehicle starts
to
roll (e.g.
on a
hiLl).

- The interior temperature deviates from
the air

conditioner setting.
- The windscreen
is
being defrosted
*$?.

- The brake pedal
is
pressed several times
in
suc­

cession.

- The vehicle battery charge drops
to an
insuffi­
cient level.

1'
May vary in different countries
80