2021 Alfa Romeo 4C ignition

Manual mirror folding
If necessary, fold the mirrors, moving
them from position 1 to position 2 fig.
13.
IMPORTANT When driving, the mirrors
should always be in position 1.
Mirror demisting(where provided)
Press button fig. 14 to enable this
function.
Activation is indicated by the digital
warning light on the display.
Press again to disable the function in
advance.
13A0L0015
14A0L0025
EXTERNAL LIGHTS
The left stalk fig. 15 operates most of
the external lights.
The external lights can only be switched
on when the ignition key is at MAR.
The instrument panel and the dashboard
and central tunnel controls will light up
together with the exterior lights.
15A0L0020
KNOWING YOUR CAR
16
11)As the driver’s door mirror is curved, it
may slightly alter the perception of
distance.
IMPORTANT

17
DRL (Daytime Running Lights)
With the ignition key at MAR and ring nut
1 fig. 15 turned to å, the daytime
running lights switch on.
The other lights and interior lighting stay
off.
IMPORTANT The daytime running lights
are an alternative to the dipped
headlights for driving during the daytime
in countries where it is compulsory to
have lights on during the day; where it is
not compulsory, the use of daytime
running lights is permitted.
IMPORTANT Daytime running lights
cannot be used in place of dipped
headlights when driving through tunnels
or at night.
The use of daytime running lights is
governed by the Highway Code of the
country in which you are driving. Comply
with legal requirements.
SIDE LIGHTS/DIPPED BEAM
HEADLIGHTS
With the ignition key at MAR and ring nut
1 fig. 15 turned to 2.The daytime running lights are switched
off and the side lights and dipped beam
headlights are switched on.
Warning light 3comes on in the
instrument panel.
PARKING LIGHTS
These lights can only be switched on
with ignition key at STOP or removed, by
moving ring nut 1 fig. 15 first to position
åand then to position 2.
The warning light 3on the instrument
panel will come on.
MAIN BEAM HEADLIGHTS
To activate the main beam headlights,
with ring nut A at 2, pull the stalk
towards the steering wheel beyond the
end of travel position.
The warning light 1on the instrument
panel will come on. When the stalk is
pulled towards the steering wheel again,
beyond the end of travel position, the
main beam headlights deactivate, the
dipped beam headlights reactivate and
the 1warning light switches off.
FLASHING
To do this, pull the stalk towards the
steering wheel (unstable position),
regardless of the position of ring nut 1
fig. 15. The warning light 1on the
instrument panel will come on.
DIRECTION INDICATORS
Bring the left stalk fig. 15 to the (stable)
position:
❒ upwards: activates right direction
indicator;
❒ downwards: activates left direction
indicator.
The Dor Fwarning light will flash on
the instrument panel.
The direction indicators are switched off
automatically when the steering wheel is
straightened.
“FOLLOW ME HOME” DEVICE
This device allows you to illuminate the
area in front of the car for a certain
amount of time.
Activation
With the key turned to STOP or
removed, pull the left-hand stalk fig. 15
towards the steering wheel within 2
minutes from when the engine is turned
off.
Each time the stalk is moved, the lights
stay on for an extra 30 seconds up to a
maximum of
210 seconds; then the lights are
switched off automatically.
Deactivation
Keep the stalk fig. 15 pulled towards the
steering wheel for more than 2 seconds.

REAR FOG LIGHT
Operation
Press the 4fig. 16 button to switch the
light on/off.
The LED on the button lights up to
indicate the activation of the rear fog
light. The rear fog light switches on only
when the dipped headlights are on.
16A0L0024
INTERIOR LIGHTS
ROOF LIGHT
The lens of roof light 1 fig. 17 can be set
to three positions:
❒ right side pressed: light always on
❒ left side pressed: light always off
❒ central position (neutral): the light
turns on and off when the doors are
opened or closed.
17A0L0060
ROOF LIGHT TIMING
To facilitate getting in/out of the car at
night or in poorly lit areas, two timed
modes have been provided.
Timing while getting into the car
The roof light switches on as follows:
❒ for about 10 seconds when the doors
are unlocked;
❒ for about 3 minutes when one of the
doors is opened;
❒ for about 10 seconds when one of the
doors is closed.
The timed period is interrupted when the
ignition is turned to “MAR-ON”.
KNOWING YOUR CAR
18

19
Timing while getting out of the car
After removing the key from the ignition
switch, the roof light will switch on as
follows:
❒ for about 10 seconds, if the key is
removed within 2 minutes of the engine
switching off;
❒ for about 3 minutes when one of the
doors is opened;
❒ for about 10 seconds when one of the
doors is closed.
The timing stops automatically when the
doors are locked.
WINDSCREEN WASHER/
WIPER
This operates only with the ignition key
turned to MAR.
Operation
12) 13)
Ring nut 1 fig. 18 can be set to the
following positions:
å windscreen wiper off;
intermittent operation;
continuous slow operation;
continuous fast operation.
18A0L0021
Move the stalk upwards (unstable
position) to limit operation to the time
for which the stalk is held in this
position. When released, the stalk will
return to its initial position and the
screen wiper will be stopped
automatically.
With ring nut 1 fig. 18 in position,
the windscreen wiper will automatically
adapt its operating speed to the speed
of the vehicle.
12)Do not use the screen wiper to
remove layers of snow or ice from the
windscreen. In such conditions, the
windscreen wiper may be subjected to
excessive stress and the motor cut-out
switch, which prevents operation for a
few seconds, may intervene.
If operation is not restored
(even after restarting that car with the
key), contact a dedicated Alfa Romeo
Dealership.
13)Do not operate the screen wiper with
the blades lifted from the windscreen.
IMPORTANT

23
ELECTRIC WINDOWS
These operate when the ignition key is
turned to MAR and for about three
minutes after the ignition key is turned to
STOP or removed unless one of the doors
is opened.
The buttons are located on the central
tunnel.
14)
CONTROLS
1 - opening/closing of left-hand window;
2 - opening/closing of right-hand
window.
Push the corresponding buttons to
open/close the desired window.
When one of the two buttons is pressed
briefly, the window moves in stages; if
the button is held down to open,
“continuous automatic” operation is
activated.
21A0L0002
If the button is pressed again the window
will stop in its current position. If the
button is pressed for several seconds,
the window lowers automatically (only
with ignition key in MAR position).
Automatic continuous operation (where provided)
This is activated by pressing one of the
two buttons for longer than half a
second. The window stops when it
reaches the end of travel position, or
when the button is pressed again.
It can be used on both the driver side and
passenger side, only for lowering the
window.
Electric window system initialisation
After there has been no power supply
for the control units (battery replaced or
disconnected or protective fuses for the
electric window control units replaced),
the automatic operation of the windows
must be restored.
The restoration procedure must be
performed as described below with the
doors closed:
❒ completely open the driver’s door
window keeping the operating button
pressed for at least three seconds after
the (lower) end of travel position;❒ completely raise the driver’s side
window and keep the button pressed for
at least three seconds once the end of
travel position (upper end stop) has been
reached;
❒ repeat stages 1 and 2 for the
passenger-side window;
❒ make sure that the initialisation is
correct by checking that the windows
work automatically.
14)Incorrect use of the electric windows
may be dangerous. Before and during
their operation, ensure that any
passengers are not at risk from the
moving glass either by personal objects
getting caught in the mechanism or by
being hit by it directly. When leaving the
car, always remove the key from the
ignition to prevent accidental operation
of the electric windows from being a
hazard for those still on board.
IMPORTANT

KNOWING THE INSTRUMENT PANEL TOOLS
36
Warning lights on panelMeaning What to do
Drive carefully and contact a dedicated
Alfa Romeo Dealership as soon as possible.
ABS FAULT
The warning light switches on when the ignition key is
turned to MAR, but it should switch off after a few
seconds.
The warning light switches on to indicate a system fault.
In this case the braking system maintains its efficiency
unaltered but without the advantage of the ABS system.
The display shows the dedicated message.
PASSENGER SIDE AIRBAG DEACTIVATED
The warning light
“comes on when the front passenger
airbag is deactivated.
With the front passenger airbag enabled, when the
ignition key is turned to MAR, the
“warning light
switches on constantly for about 4 seconds then it should
switch off.
If the warning light flashes, this indicates an airbag
warning light fault.
22)
Drive carefully and contact a dedicated Alfa Romeo
Dealership as soon as possible.

37
Warning lights on panelMeaning What to do
In this case release the accelerator pedal to lower the
engine speed until the warning light stops flashing.
Continue the journey at moderate speed, trying to avoid
driving conditions that may cause further flashing and
contact a dedicated Alfa Romeo Dealership as soon as
possible.
If the Uwarning light flashes, it means that the catalytic
converter may be damaged.
3)
Under these conditions, the vehicle can continue travelling
at moderate speed without demanding excessive effort
from the engine. Prolonged use of the car with the warning
light on constantly may cause damage.
Contact a dedicated Alfa Romeo Dealership as soon as
possible. INJECTION / EOBD SYSTEM FAILURE
In normal conditions, when the ignition key is turned to
MAR the Uwarning light switches on, but it should
switch off as soon as the engine is started.
The operation of the Uwarning light may be checked by
traffic police using appropriate equipment.
Comply with the laws and regulations of the country
where you are driving.
If the Uwarning light stays on or switches on when
driving, it means that the injection system is not working
properly; in particular, if the warning light comes on
constantly, this indicates a malfunction in the
supply/ignition system that could cause excessive
exhaust emissions, a possible loss of performance, poor
driveability and high fuel consumption.
On some versions the display shows the dedicated
message.
The Uwarning light switches off if the malfunction
disappears, but is still stored by the system.

39
Warning lights on panelMeaningWhat to do
ASR OFF WARNING LIGHT
When the ignition key is turned to MAR, the warning light
switches on, but should switch off as soon as the engine is
started.
The warning light switches on when the ASR function
of the electronic stability control (ESC) system is
deactivated (by selecting “Race” mode).
The ASR warning light goes off.
Contact a dedicated Alfa Romeo Dealership as soon as
possible to have the problem corrected.
Contact a dedicated Alfa Romeo Dealership as soon as
possible. ESC ELECTRONIC STABILITY CONTROL SYSTE
When the ignition key is turned to MAR, the warning light
switches on, but should switch off as soon as the engine is
started.
Intervention by the system is indicated by the flashing of
the warning light: it indicates that the car is in critical
stability and grip conditions.
If the warning light does not switch off, or if it stays on
with the engine running, a failure was found on the ESC
system.
Hill Holder system fault
The digital warning light
*switches on and the display
shows the dedicated message, informing about Hill Start
system failure.