2020 YAMAHA YFZ50 oil pressure

5-3
5
EBU38000FuelMake sure there is sufficient gasoline in the tank
before starting off. Refuel if necessary. (See page
4-9.)EBU19561Engine oilMake sure that the engine oil is at the specified
level. Add oil as necessary. (See page 8-11.)EBU34490Transmission oilMake sure that the transmission oil is at the spec-
ified level. Add oil as necessary. (See page 8-15.)EBU19653Front and rear brakesBrake levers
Check for correct free play in the brake levers. If
the free play is incorrect, adjust it. (See pages
8-24 and 8-26.)
 Check operation of the levers. They should
move smoothly and there should be a firm feel-
ing when the brake is applied. If not, have the
ATV checked by a Yamaha dealer. Brake operation
Test the brakes at slow speed after starting out to
make sure they are working properly. If the brakes
do not provide proper braking performance,
check the brake shoes for wear. (See page 8-23.)
EBU19762Throttle leverCheck the operation of the throttle lever. It must
open smoothly and spring back to the idle position
when released. Have a Yamaha dealer correct if
necessary.EBU19771Drive chainCheck the condition of the drive chain and check
the drive chain slack. Lubricate and adjust the
drive chain as necessary. (See page 8-26.)EBU19799TiresCheck tire pressure regularly to make sure it is at
the recommended specifications. Also check for
wear and damage.
UBW463E0.book Page 3 Monday, January 28, 2019 10:22 AM

8-6
8
5*Wheels • Check runout and for damage, and replace if nec-
essary. √ √√√
6 *Tires • Check tread depth and for damage, and replace if
necessary.
• Check air pressure and balance, and correct if necessary. √ √√√
7 *Wheel hub bearings • Check for looseness or damage, and replace if
necessary. √ √√√
8 *Front arm pivots • Lubricate with lithium-soap-based grease. √√√
9 Drive chain • Check chain slack and adjust if necessary.
• Check rear wheel alignment and correct if neces-
sary.
• Clean and lubricate. √√√√√
10 *V- b e l t • Check for wear, cracks or other damage, and re-
place if necessary. √ √√√
11 *Chassis fasteners • Make sure that all nuts, bolts, and screws are
properly tightened. √√√√√
12 *Shock absorber as-
semblies • Check operation and correct if necessary.
• Check for oil leakage and replace if necessary.
√√√
13 *Front knuckle piv-
ots • Lubricate with lithium-soap-based grease.
√√√
14 *Steering shaft • Lubricate with lithium-soap-based grease. √√√
NO. ITEM
CHECK OR MAINTENANCE
JOB INITIAL EVERY
Whichev- er comes first month136612
km (mi) 240
(150) 1300
(800) 2500
(1600) 2500
(1600) 5000
(3200)
hours 20 80 160 160 320
UBW463E0.book Page 6 Monday, January 28, 2019 10:22 AM

10-3
10
Transmission type:CVT automatic
Gear ratio: Transmission ratio:2.140–0.710 : 1
Forward gear: 10.967 (49/15 x 47/14)Front tire:Size:AT16x6.5-7
Manufacturer/model: DURO/DI2040Rear tire:Size:AT16x7-7
Manufacturer/model: DURO/DI2041Tire air pressure (measured on cold tires):Vehicle load:0.0–41.0 kg (0–90 lb)
Recommended: Front:15.0 kPa (0.150 kgf/cm², 2.2 psi)
Rear: 15.0 kPa (0.150 kgf/cm², 2.2 psi)
Minimum:
Front:12.0 kPa (0.120 kgf/cm², 1.7 psi)
Rear:
12.0 kPa (0.120 kgf/cm², 1.7 psi)
Front wheel:Rim size:7 x 5.2ATRear wheel:Rim size:7 x 5.2ATFront brake:Type:
Mechanical leading, trailing drum brakeRear brake:Type:Mechanical leading, trailing drum brakeFront suspension:Type:Swing axle
Spring: Coil spring
Shock absorber:
Gas-hydraulic damper
Wheel travel: 60 mm (2.4 in)Rear suspension:Type:
Swingarm
Spring: Coil spring
Shock absorber: Gas-hydraulic damper
Wheel travel:
51 mm (2.0 in)
UBW463E0.book Page 3 Monday, January 28, 2019 10:22 AM