2020 YAMAHA YFM700R low beam

Checking the front brake lever free play ... 9-35
Checking the brake pedal height .............. 9-35
Adjusting the parking brake free play ....... 9-36
Brake light switches .................................. 9-37
Adjusting the clutch lever free play ........... 9-38
Drive chain slack ....................................... 9-39
Lubricating the drive chain........................ 9-41
Checking and lubricating the cables......... 9-42
Checking and lubricating the brake and clutch levers ............................................ 9-43
Checking the shift pedal ........................... 9-43
Checking and lubricating the brake pedal ....................................................... 9-43
Checking the wheel hub bearings............. 9-43
Lubricating the swingarm pivots ............... 9-44
Lubricating the rear suspension relay arm and connecting arm pivoting points ....... 9-44
Lubricating the upper and lower arm pivots ...................................................... 9-45
Lubricating the steering shaft ................... 9-46
Battery....................................................... 9-47
Replacing a fuse ....................................... 9-50
Replacing a headlight bulb ....................... 9-52
Adjusting a headlight beam ...................... 9-53
Brake/tail light ........................................... 9-54
Removing a wheel ..................................... 9-54
Installing a wheel....................................... 9-54 Troubleshooting........................................ 9-55
Troubleshooting charts ............................. 9-56
CLEANING AND STORAGE......................... 10-1 Cleaning.................................................... 10-1
Storage ..................................................... 10-2
SPECIFICATIONS ........................................ 11-1
INDEX .......................................................... 12-1
UBCX60E0.book Page 3 Friday, April 19, 2019 9:09 AM

5-4
5
EBU18081Engine stop switch “ / ”
Set this switch to “ ” before starting the engine.
The engine stop switch controls the ignition and
stops the engine when it is running. Use this
switch to stop the engine in an emergency situa-
tion. The engine will not start or run when this
switch is set to “ ”.EBU18102Start switch “ ”
Push this switch to crank the engine with the start-
er. See the starting instructions on page 7-1 prior
to starting the engine.EBU18157Light switch “ / /OFF”
Set this switch to “ ” to turn on the low beams
and the taillight. Set the switch to “ ” to turn on
the high beams and the taillight. Set the switch to
“OFF” to turn off all the lights.NOTICEECB00046Do not use the headlights with the engine
turned off for an extended period of time. The
battery may discharge to the point that thestarter will not have enough power to crank the
engine. If this should happen, remove the bat-
tery and recharge it. (See page 9-47.)
EBU18286Throttle leverPush the throttle lever to increase engine speed.
Spring tension returns the lever to the rest position
when released. Always check that the throttle le-
ver returns normally before starting the engine. 1. Throttle lever
1
UBCX60E0.book Page 4 Friday, April 19, 2019 9:09 AM

9-54
9
To raise a headlight beam, turn the headlight
beam adjusting bolt in direction (a).
To lower a headlight beam, turn the adjusting bolt
in direction (b).
EBU26922Brake/tail lightThis model is equipped with an LED type of
brake/tail light.
If the brake/tail light does not come on, have a
Yamaha dealer check it.EBU25653Removing a wheel1. Park the ATV on a level surface. 2. Loosen the wheel nuts.
3. Elevate the ATV and place a suitable stand
under the frame.
4. Remove the nuts from the wheel.
5. Remove the wheel.
EBU27484Installing a wheel1. Install the wheel with the arrow mark pointing in the forward rotating direction of the wheel,
and then install the wheel nuts.
1. Headlight beam adjusting bolt1
(a)(b)
1. Wheel nut
UBCX60E0.book Page 54 Friday, April 19, 2019 9:09 AM