Page 8 of 86

Table of contents
Location of important la bels ........... 1-1
Safety information ............................ 2-1
Description ....................................... 3-1
Left view ......................................... 3-1
Right view ....................................... 3-2
Controls and instruments ............... 3-3
Instrument an d control functions ... 4-1
Main switch .................................... 4-1
Handlebar switches ........................ 4-1
Speed limiter .................................. 4-2
Shift pedal ...................................... 4-3
Brake lever...................................... 4-3
Brake pedal .................................... 4-4
Fuel tank cap .................................. 4-4
Fuel ................................................. 4-5
Fuel tank breather hose.................. 4-6
Fuel cock ........................................ 4-7
Starter (choke) lever ...................... 4-8
Seat ................................................ 4-8
Sidestand ....................................... 4-9
Starting circuit cut-off system ........ 4-9
For your safety – pre-operation
checks ............................................... 5-1
Operation an d important ri din g
points ................................................ 6-1
Starting and warming up a cold engine ......................................... 6-1
Starting a warm engine .................. 6-2
Shifting ........................................... 6-2
Engine break-in .............................. 6-3
Parking ........................................... 6-4
Perio dic maintenance an d
a d justment ........................................ 7-1
Periodic maintenance chart for the emission control system ............. 7-3
General maintenance and lubrication chart .......................... 7-4
Checking the spark plug ................ 7-6
Engine oil ........................................ 7-7
Cleaning the air filter element ......... 7-9 Cleaning the spark arrester ........... 7-10
Adjusting the carburetor ............... 7-11
Adjusting the engine idling
speed ......................................... 7-12
Checking the throttle grip free
play ............................................ 7-13
Valve clearance ............................. 7-13
Tires .............................................. 7-14
Spoke wheels ................................ 7-15
Adjusting the clutch free play........ 7-16
Adjusting the brake lever free play ............................................ 7-17
Adjusting the brake pedal free play ............................................ 7-18
Checking the shift pedal ............... 7-19
Checking the front and rear brake shoes ......................................... 7-19
Drive chain slack ........................... 7-20
Cleaning and lubricating the drive chain ................................. 7-22
Checking and lubricating the cables ........................................ 7-22
Checking and lubricating the
throttle grip and cable ............... 7-23
Checking and lubricating the brake lever ................................. 7-23
Checking and lubricating the brake pedal ................................ 7-24
Checking and lubricating the
sidestand ................................... 7-24
Lubricating the swingarm pivots ... 7-25
Checking the front fork ................. 7-25
Checking the steering ................... 7-26
Checking the wheel bearings ........ 7-26
Battery........................................... 7-27
Replacing the fuse ........................ 7-28
Supporting the motorcycle ........... 7-29
Front wheel ................................... 7-30
Rear wheel .................................... 7-31
Troubleshooting ............................ 7-33
Troubleshooting chart ................... 7-34
Motorcycle care an d stora ge .......... 8-1
Matte color caution ......................... 8-1
Care................................................. 8-1
Storage............................................ 8-4
UBEG80E0.book Page 1 Friday, May 24, 2019 6:49 PM
Page 25 of 86
Description
3-2
3
EAU63391
Right view
4
65 3 2
1
1. Seat (page 4-8)
2. Fuel tank cap (page 4-4)
3. Spark plug cap (page 7-6)
4. Brake pedal (page 4-4)
5. Clutch adjusting screw (page 7-16)
6. Engine oil filler cap (page 7-7)
UBEG80E0.book Page 2 Friday, May 24, 2019 6:49 PM
Page 26 of 86
Description
3-3
3
EAU63401
Controls and instruments
12 3 4
65
1. Engine stop switch (page 4-1)
2. Starter (choke) lever (page 4-8)
3. Main switch (page 4-1)
4. Brake lever (page 4-3)
5. Throttle grip (page 7-13)
6. Start switch (page 4-1)
UBEG80E0.book Page 3 Friday, May 24, 2019 6:49 PM
Page 29 of 86
Instrument and control functions
4-3
4
EAU39852
Shift pe dal
This motorcycle is equipped with a
constant-mesh 3-speed transmission.
The shift pedal is located on the left
side of the motorcycle. Neutral is at the
bottom position.
EAU12892
Brake lever
The brake lever is located on the right
side of the handlebar. To apply the
front brake, pull the lever toward the
throttle grip.
1. Shift pedal
2. Neutral position1. Brake lever
1
UBEG80E0.book Page 3 Friday, May 24, 2019 6:49 PM
Page 30 of 86
Instrument and control functions
4-4
4
EAU12944
Brake ped al
The brake pedal is located on the right
side of the motorcycle. To apply the
rear brake, press down on the brake
pedal.
EAU13183
Fuel tank cap
To remove the fuel tank cap, turn it
counterclockwise, and then pull it off.
To install the fuel tank cap, insert it into
the tank opening, and then turn it
clockwise.
WARNING
EWA11092
Make sure that the fuel tank cap is
properly close d after fillin g fuel.
Leakin g fuel is a fire hazar d.
1. Brake pedal
1
1. Fuel tank cap
1
UBEG80E0.book Page 4 Friday, May 24, 2019 6:49 PM
Page 36 of 86
Instrument and control functions
4-10
4
With the engine t urned off:
1. Set engine stop s witch to run position.
2. T urn main s witch to on position.
3. Shift transmission into gear.
5. Push the start s witch.
4. Apply front or rear
brake.
Does the engine start?
6. Shift transmission into ne utral.
7. Push the start s witch.
Does the engine start?
The system is OK.
The motorcycle can be ridden.
The neutral s witch may not be w orking.
The motorcycle should not be ridden
until checked b y a Yamaha dealer.
The neutral switch may not be w orking.
The motorcycle should not be ridden
until checked b y a Yamaha dealer.
WARNING
If a malfunction is found, have the
vehicle inspected before riding.
NO YES
YES NO
UBEG80E0.book Page 10 Friday, May 24, 2019 6:49 PM
Page 37 of 86

For your safety – pre-operation checks
5-1
5
EAU63441
Inspect your vehicle each time you use it to make sure the vehicle is in safe oper-
ating condition. Always follow the inspection and maintenance procedures and
schedules described in the Owner’s Manual.
WARNING
EWA11152
Failure to inspect or maintain the vehicle properly increases the possibility
of an acci dent or equipment d amage. Do not operate the vehicle if you fin d
any prob lem. If a pro blem cannot be corrected b y the proce dures provi ded
in this manual, have the vehicle inspecte d b y a Yamaha d ealer.
Before using this vehicle, check the following points:
ITEM CHECKSPAGE
Fuel • Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage.
• Check fuel tank breather hose for obstructions, cracks
or damage, and check hose connection. 4-5, 4-6
En gine oil • Check oil level in engine.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage. 7-7
Front brake • Check operation.
• Lubricate cable if necessary.
• Check lever free play.
• Adjust if necessary. 7-17,
7-19
Rear brake • Check operation.
• Check pedal free play.
• Adjust if necessary. 7-18,
7-19
Throttle g rip • Make sure that operation is smooth.
• Check throttle grip free play.
• If necessary, have Yamaha dealer adjust throttle grip
free play and lubricate cable and grip housing. 7-13,
7-23
Control ca bles • Make sure that operation is smooth.
• Lubricate if necessary. 7-22
Drive chain • Check chain slack.
• Adjust if necessary.
• Check chain condition.
• Lubricate if necessary. 7-20,
7-22
Wheels an d tires •Check for damage.
• Check tire condition and tread depth.
• Check air pressure.
• Correct if necessary. 7-14,
7-15
Shift pe dal • Make sure that operation is smooth.
• Correct if necessary. 7-19
Brake ped al • Make sure that operation is smooth.
• Lubricate pedal pivoting point if necessary.
7-24
UBEG80E0.book Page 1 Friday, May 24, 2019 6:49 PM
Page 38 of 86
For your safety – pre-operation checks
5-2
5
Brake lever• Make sure that operation is smooth.
• Lubricate lever pivoting point if necessary. 7-23
Si destan d • Make sure that operation is smooth.
• Lubricate pivot if necessary.
7-24
Chassis fasteners • Make sure that all nuts, bolts and screws are properly
tightened.
• Tighten if necessary. —
En gine stop switch • Check operation. 4-1
ITEM CHECKS PAGE
UBEG80E0.book Page 2 Friday, May 24, 2019 6:49 PM