2020 YAMAHA TMAX wheel bolts

For your safety – pre-operation checks
6-2
6
Rear brake • Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add specified brake fluid to specified level.
• Check hydraulic system for leakage. 8-22, 8-24, 8-24
Throttle grip • Make sure that operation is smooth.
• Check throttle grip free play.
• If necessary, have Yamaha dealer adjust throttle grip free play and lubricate ca-
ble and grip housing. 8-18, 8-27
Wheels an d tires • Check for damage.
• Check tire condition and tread depth.
• Check air pressure.
• Correct if necessary. 8-19, 8-21
Brake levers • Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary. 8-27
Centerstan d, si destan d • Make sure that operation is smooth.
• Lubricate pivots if necessary.
8-28
Chassis fasteners • Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.
—
Instruments, li ghts, si gnals
an d switches • Check operation.
• Correct if necessary.
—
Si destan d switch • Check operation of ignition circuit cut-off system.
• If system is not working correctly, have Yamaha dealer check vehicle.
5-29
Drive belt • Check belt condition.
• Replace if damaged.
8-26
ITEM CHECKS PAGE
UB3TE0E0.book Page 2 Tuesday, September 17, 2019 9:35 AM

Periodic maintenance an d a djustment
8-6
8
12 *Tires • Check tread depth and for dam-
age.
• Replace if necessary.
• Check air pressure.
• Correct if necessary. √√√√√
13 *Wheel bearin gs • Check bearing for looseness or
damage. √√√√
14 *Drive belt • Check belt condition.
• Replace if damaged.
• Check belt tension.
• Adjust if necessary. At the initial interval and every 10000 km (6000 mi) until 40000 km (24000 mi),
and every 5000 km (3000 mi) thereafter.
15 *Drive pulley an
d
d rive axle • Lubricate.
√√
16 *Steerin g b earin gs • Check bearing assemblies for
looseness. √√ √
• Moderately repack with lithium- soap-based grease. √√
17 *Chassis fasteners • Make sure that all nuts, bolts and
screws are properly tightened. √√√√√
18 Front an
d rear
b rake lever pivot
shaft • Lubricate with silicone grease.
√√√√√
19 *Si
destan d, center-
stan d • Check operation.
• Lubricate with lithium-soap-
based grease. √√√√√
20 *Sidestan d switch • Check operation and replace if
necessary. √√√√√√
NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READING
ANNUAL
CHECK
1000 km
(600 mi) 10000 km
(6000 mi) 20000 km
(12000 mi) 30000 km
(18000 mi) 40000 km
(24000 mi)UB3TE0E0.book Page 6 Tuesday, September 17, 2019 9:35 AM

Periodic maintenance an d a djustment
8-26
8
EAU88810
Drive b eltThe drive belt should be visually in-
spected before each ride. Check for
excessive wear, damage, and dirt. Al-
so, the drive belt tension must be
checked and adjusted by a Yamaha
dealer at the intervals specified in the
periodic maintenance chart.
To check the drive belt
1. On a level surface, place the vehi- cle on its centerstand.
2. Rotate the rear wheel and check the belt surface for signs of wear
or damage. 3. If cracks, excessive wear, or dam-
age is found, have the belt in-
spected or replaced by your
Yamaha dealer.
4. If the drive belt or drive belt sprocket is dirty, remove the drive
belt covers by removing the bolts
and quick fasteners.
5. Clean the drive belt and remove any debris from the drive belt
sprocket. NOTICE: Do not allow
d irt or san d to accumulate in the
d rive belt area, otherwise the
d rive belt will wear out quickly.
[ECA26970]
6. Install the drive belt covers by in-
stalling the bolts and quick fasten-
ers.
1. Stone damage
2. Cog damage
1
2
1. Quick fastener
2. Bolt
3. Drive belt cover1 23
UB3TE0E0.book Page 26 Tuesday, September 17, 2019 9:35 AM