2020 YAMAHA TMAX lock

Smart key system
3-9
3

The power of the vehicle cannot
be turned off via the “OFF/LOCK”
switch when the vehicle is moving.
If the smart key is not within operating
range or cannot communicate with the
vehicle when you press the
“OFF/LOCK” switch, the vehicle will
not be turned off and the beeper will
sound for three seconds (the smart key
system indicator light will also flash) to
alert you that the power was not suc-
cessfully turned off. Confirm the loca-
tion and condition of the smart key and
try powering off the vehicle again.TIPWithout the smart key, the vehicle
power can be turned off by pressing
the “OFF/LOCK” switch again while
the smart key system indicator light is
flashing.Auto lock function
After the engine is stopped via the
“OFF/LOCK” switch and also whenev-
er the vehicle power is turned from on
to off, all storage compartment locks
and the fuel tank cap lid lock are re- leased. When 60 seconds have
passed, all compartments will auto-
matically lock.
When the compartment locks are re-
leased via the “ / ” switch, the
compartments will automatically lock
after 10 seconds have passed.
EAU80002
How to lock the steerin
gWith the vehicle power off, turn the
handlebars fully to the left and then
briefly press the “OFF/LOCK” switch.TIPIf the steering lock function locks
correctly, the beeper will sound
once.
 If the steering lock function does
not lock correctly, the beeper will
sound for three seconds and the
smart key system indicator light
will flash. Turn the handlebar fully
to the left one more time and press
the “OFF/LOCK” switch again.
UB3TE0E0.book Page 9 Tuesday, September 17, 2019 9:35 AM

Smart key system
3-10
3
WARNING
EWA14742
Do not operate the steering lock
while the vehicle is movin g.
EAU78052
How to lock the centerstan dPark the vehicle on a firm level surface
and then place it on the centerstand.
Press the “OFF/LOCK” switch for one
second.TIPIf the centerstand lock function
locks correctly, the beeper will
sound once.
 If the centerstand lock function
does not lock correctly, the beep-
er will sound for three seconds
and the smart key system indica-
tor light will flash. Gently rock the vehicle forward or backward and
press the “OFF/LOCK” switch for
one second.1. “OFF/LOCK” switch
1
UB3TE0E0.book Page 10 Tuesday, September 17, 2019 9:35 AM

Smart key system
3-11
3
EAU81291
Storage compartment an d
fuel tank accessTo open the seat
1. Place the vehicle on the center- stand.
2. Briefly press the “ / ” switch. Upon authentication of the smart
key, the beeper will sound twice.
3. Press the “SEAT” button and the seat lock will release. 4. Fold the seat up.
To close the seat
Fold the seat down, and then push it to
lock it in place.
TIP Make sure the seat is properly
closed before starting off. 
In case of an emergency, the seat
can be opened with a mechanical
key. (See page 8-38.)
To open the fuel tank cap li d
With the smart key on and in operating
range, briefly press the “ / ” switch.
Upon authentication of the smart key,
the beeper will sound twice. 1. Press the “FUEL” button.
2. Open the lid as shown.
1. “ / ” switch1
1. “SEAT” button
1
1. “FUEL” button
1
UB3TE0E0.book Page 11 Tuesday, September 17, 2019 9:35 AM

Smart key system
3-13
3
EAU80842
Parking mo deThe steering is locked, and the hazard
lights and turn signal lights can be
turned on, but all other electrical sys-
tems are off.
To enter parkin g mo de
1. Lock the steering. (See page 3-9.)
2. Press the “ / ” switch for one second.TIPIf the steering lock has not been ap-
plied, the beeper will sound for 3 sec-
onds (the smart key system indicator
light will also flash) and the vehicle will
not enter parking mode.3. Upon authentification of the smartkey, the beeper will sound twice
and the vehicle will enter parking
mode. The smart key system indi-
cator light will come on.TIPThe seat, fuel tank cap lid, and the front
storage compartment (for XP560D)
cannot be opened while in parking
mode.
NOTICE
ECA20760
Usin g the hazar d or turn si gnal lig hts
for an exten ded len gth of time may
cause the b attery to discharge.To exit parkin g mo de
Press the “ / ” switch. Upon au-
thentication of the smart key, the beep-
er will sound once and the smart key
system indicator light will go off.
UB3TE0E0.book Page 13 Tuesday, September 17, 2019 9:35 AM

Instrument and control functions
5-4
5 the anti-lock brake system may not
work correctly. Have a Yamaha dealer
check the vehicle as soon as possible.
WARNING
EWA16043
If the ABS warnin
g lig ht does not
turn off after reachin g 10 km/h (6
mi/h), or if the warnin g li ght comes
on while ri din g:
 Use extra caution to avoi d pos-
si ble wheel lock d uring emer-
g ency brakin g.
 Have a Yamaha dealer check
the vehicle as soon as possi ble.TIPThe ABS warning light may come on
when revving the engine with the
scooter on its centerstand, but this
does not indicate a malfunction.
EAU88700
Traction control system in dicator
li g ht “ ”
This indicator light will flash when trac-
tion control has engaged.
If the traction control system is turned
off, this indicator light will come on.
TIPWhen the vehicle is turned on, the light
should come on for a few seconds and
then go off. If the light does not come
on, or if the light remains on, have a
Yamaha dealer check the vehicle.
EAU78083
Smart key system in dicator
li g ht “ ”
This indicator light will flash when com-
munication between the vehicle and
smart key takes place and when cer-
tain smart key system operations are
carried out.
The indicator light may also flash when
there is an error in the smart key sys-
tem.TIPWhen the vehicle is turned on, the light
should come on for a few seconds and
then go off. If the light does not come
on, or if the light remains on, have a
Yamaha dealer check the vehicle.
EAU77131
Speed ometerThe speedometer shows the vehicle’s
traveling speed.
When the vehicle power is turned on,
the speedometer needle will sweep
across the speed range and return to
zero in order to test the electrical cir-
cuit.1. Speedometer
1 1
1
UB3TE0E0.book Page 4 Tuesday, September 17, 2019 9:35 AM

Instrument and control functions
5-5
5
EAU77141
TachometerThe tachometer shows the engine
speed in crankshaft revolutions per
minute (r/min).
When the vehicle power is turned on,
the tachometer needle will sweep
across the r/min range and return to
zero in order to test the electrical cir-
cuit.NOTICE
ECA23050
Do not operate the en gine in the ta-
chometer hi gh-r/min zone.
Hi gh-r/min zone: 8250 r/min an d
a b ove
EAU7733A
Multi-function display
WARNING
EWA12313
Be sure to stop the vehicle before
makin g any settin g chan ges to the
multi-function display. Chan gin g
settin gs while ri din g can d istract the
operator an d increase the risk of an
acci dent.TIPCertain multi-function display items
can be adjusted via the setting mode.
(See page 5-11.)
1. Tachometer
2. High-r/min zone
1 1
2
2
1. Information display
2. Function select icon
3. Fuel meter
4. Clock
5. Grip warmer/Seat heater icons
6. Drive mode display
7. Coolant temperature meter
1 2 3 4 5
6
7
1. Oil change indicator “Oil”
2. V-belt replacement indicator “V-Belt”
3. Eco indicator “ECO”
1 2
3
UB3TE0E0.book Page 5 Tuesday, September 17, 2019 9:35 AM

Instrument and control functions
5-9
5
NOTICE
ECA23980
 Be sure to wear protective
clothin g that covers your hip
an d le gs when usin g the seat
heater.
 If the am bient temperature is 20
°C (68 °F) or hi gher, do not set
the seat heater to the hi gh set-
ting .
 If the seat b ecomes worn or
d amag ed , stop using the seat
heater an d replace the seat.Changing the information displayThe information display items are
grouped into 3 display pages. Push the “ ” or “ ” side of the se-
lect switch to rotate among the 3 dis-
play pages.
TIPThe items for each display page can be
customized. (See page 5-15.)Odometer:The odometer shows the total distance
traveled by the vehicle.
Tripmeters:“TRIP1” and “TRIP2” show the dis-
tance traveled since they were last set
to zero. To reset a tripmeter, use the select
switch to select the information display
page that contains the tripmeter you
want to reset. Push the “ ” side of
the select switch for one second so
that the tripmeter flashes, and then
push the “ ” side of the select switch
again for one second while the tripme-
ter is flashing.
TIP
The odometer will lock at 999999.
 The tripmeters will reset and con-
tinue counting after 9999.9 is
reached.When approximately 3.0 L (0.79 US
gal, 0.66 Imp.gal) of fuel remains in the
fuel tank, the last segment of the fuel
meter starts flashing. In addition, the
information display will automatically
change to the fuel reserve tripmeter
mode “F-TRIP” and start counting the
distance traveled from that point.
UB3TE0E0.book Page 9 Tuesday, September 17, 2019 9:35 AM

Instrument and control functions
5-11
5
Instantaneous fuel consumption:
The instantaneous fuel consumption
mode “CRNT.F” can be set to “km/L”
or “L/100km”. For UK-spec vehicles:
“MPG”. (See page 5-14.)TIPIf traveling at speeds under 10 km/h (6
mi/h), “– –.–” will be displayed.NOTICE
ECA15474
If there is a malfunction, “– –.–” will
b
e continuously d isplayed. Have a
Yamaha dealer check the vehicle.
Settin g mo de
Stop the vehicle and then push the
“MENU” switch for 2 seconds to enter
the setting mode. To exit the setting
mode and return to the standard dis-
play mode, push the “MENU” switch
again for 2 seconds or
select “ ”.TIPWhen the malfunction indicator light is
on, setting mode cannot be entered.Menu items1. Setting mode display
Categ ory Description
This function allows you to
set the low, middle, and
high settings to 10 tem-
perature levels.
1
Grip Warmer
This function allows you to
set the low, middle, and
high settings to 10 tem-
perature levels.
This function allows you to
turn the traction control
system on or off.
This function allows you to
check and reset the oil
change interval (indicator),
V-Belt change interval (in-
dicator), and the “FREE”
maintenance interval.
This function allows you to
switch the fuel consump-
tion units between
“L/100km” and “km/L”.
For UK-spec vehicles: this
function is not available.
This function allows you to
change the items shown in
3 information displays.
This function allows you to
adjust the brightness of
the instrument panel.
This function allows you to
set the clock.
This function allows you to
reset all items to their fac-
tory preset or default set-
tings; excepting the
odometer, clock, and
maintenance counter
items “Oil” and “V-Belt”.
Seat HeaterTraction ControlMaintenance
UnitDisplayBrightnessCloc
k
All Reset
UB3TE0E0.book Page 11 Tuesday, September 17, 2019 9:35 AM