256Driving and operatingCaution
When reversing, the area should
be free from obstacles which could impact on the underside of the
vehicle.
Impact to the rear axle, which may
not be visible, could lead to
uncharacteristic changes in the
vehicle handling. In the event of
such an impact, consult a
workshop.
Basic notes on parking assist
system
9 Warning
Under certain circumstances,
various reflective surfaces on
objects or clothing as well as
external noise sources may cause the system to fail to detect
obstacles.
Special attention must be paid to
low obstacles which can damage
the lower part of the bumper.
Caution
Performance of the sensors can
be reduced when sensors are
covered, e.g. by ice or snow.
Performance of the parking assist
system can be reduced due to
heavy loading.
Special conditions apply if there
are taller vehicles involved (e.g.
off-road vehicles, mini vans,
vans). Object identification in the
upper part of these vehicles
cannot be guaranteed.
Objects with a very small reflection
cross-section, e.g. objects of
narrow size or soft materials, may
not be detected by the system.
The parking assist system will not
detect objects which are out of the detection range of the sensors.
Side blind spot alert
The side blind spot alert system
detects and reports objects on either
side of the vehicle, within a specified
blind spot zone. The system displays
a visual alert in each exterior mirror,
when detecting objects that may not
be visible in the interior and exterior
mirrors.
Side blind spot alert uses some of the
parking assist sensors which are
located in the front and rear bumper
on both sides of the vehicle.9 Warning
Side blind spot alert does not
replace driver vision.
The system does not detect:
● vehicles outside the side blind zones which may be rapidly
approaching
● pedestrians, cyclists or animals
Before changing a lane, always
check all mirrors, look over the
shoulder and use the turn signal.
Activation
The system is activated when the
speed of the vehicle is between
approx. 19 mph and 87 mph.
260Driving and operating● the rear doors are not closedcorrectly
● the vehicle had a rear-end accident
● there are extreme temperature changes
Lane departure warning The lane departure warning system
uses a front camera to observe the
lane markings between which the
vehicle is driving. The system detects
lane changes and warns the driver in
the event of an unintended lane
change via visual and acoustic
signals.
Criteria for the detection of an
unintended lane change are:
● no operation of turn lights
● no active steering
If the driver is performing these
actions, no warning will be issued.Activation
The lane departure warning system is activated by pressing Q in the centre
console. A corresponding message
appears in the Driver Information
Centre to indicate that the system is
switched on.
When Q 3 100 illuminates in the
Driver Information Centre, the system is ready to operate 3 104.
Q extinguishes when the system is
not ready to warn the driver.
The system is only operable at
vehicle speeds above approx.
37 mph and if lane markings are
available and detected.
If the turn lights are not operated
when changing lanes, i.e. an
unintended lane change is detected,
control indicator Q flashes together
with a warning chime to alert the
driver.
330Body conversionsIsolation switch
The system must be activated using
the isolation switch located on the left- hand side of the chassis. Turn the
isolator switch to the ON position.
When the tipper is not in use, turn the
isolation switch to the OFF position.
Raising and lowering the tipper
The tipper is operated using the
remote control located by the front
seats.
The remote control enables the user
to supervise the operation of the
tipper from outside the vehicle.
Press switch:
â:raiseã:lower
When the tipper is active an acoustic
signal sounds.
The tipper can be stopped at any time
by releasing the switch.
The tipper body will cease moving
automatically when it reaches the
maximum height.
To stop in an emergency, press the
red button.
Store the remote control in the holder when not in use.
Safety cable The safety cable attached to the
tipper body prevents the tipper body
being raised too far. Should the safety
cable become damaged it must be
replaced immediately. Seek the
assistance of a workshop.
Safety prop
The safety prop is located under the
left-hand side of the tipper body and
is provided only to assist in supporting the empty tipper body when tipped to
the rear, for carrying out visual
inspection of the vehicle components.
