2020 TOYOTA SEQUOIA rear view mirror

2
OVERVIEWInstrument panel
Meter control switches
Steering wheel controls
Windshield wiper and
washer control
Voice command switch
2
Tire pressure monitor (warning)
system (TPMS) reset switch
“ENGINE START STOP” switch
Outside rear view
mirror controls Audio remote
control switches
2
Telephone switches2
Dynamic Radar
Cruise Control
(DRCC) or cruise
control switch
Vehicle-to-vehicle
distance switch

and
Lane Departure Alert
(LDA) switch
Power tilt and telescopic
steering control switch
1
Parking brake
Hood lock release lever
Personal/interior
light main switch
Power back door button
1
Automatic High Beam (AHB) switch Tilt and telescopic
steering lock release lever
1
(below the steering wheel)
Headlights/turn signals/
fog light control
Meters and
Multi-information display
(MID)

6
Indicator symbols
For details, refer to “Indicators and warning lights,” Section 2, \
2020 Owner’s
Manual.
Charging system warning1
Center differential lock indicator4
BSM w/Rear Cross Traffic Alert
(RCTA) indicator
AIR BAG ON/OFF indicator1
Anti-lock Brake System (ABS) warning1
Airbag SRS warning1
Automatic High Beam (AHB) indicator
Blind Spot Monitor (BSM) indicator
OVERVIEW
Fuel tank door position Front fog light indicator
Brake system warning1
BSM outside rearview mirror
indicator
High/Low speed four-wheel
drive indicator
4
Headlight low/
high beam indicator
AUTO Limited Slip
Differential indicator
1,4
Constant speed cruise control
indicator/Constant speed
cruise control SET indicator
Driver’s and/or front passenger’s seat
belt reminder (alarm will sound if
speed is over 12 mph)
Dynamic Radar Cruise Control
(DRCC) indicator/DRCC SET
indicator

23
OpenTilt
CloseClose
PushPush
(1)
(2)
(1)
You can save up to two driving positions to memory and recall it with th\
e touch of
a button. Make sure shift lever is in “P” position and ignition sw\
itch is in the “ON”
position.
Refer to the Owner‘s Manual for more details on this system.
To save
Adjust driver’s seat, steering wheel, and
outside rear view mirrors.Press “1” or “2” to recall until buzzer sounds.
Push “SET” and “1” or “2” buttons to save
until buzzer sounds.
To recall
SLIDING OPERATIONTILTING OPERATION
DRIVER’S SEAT
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
Lightly press either side of the moonroof switch while opening/tilting i\
s in progress,
the moonroof stops partway.
Push once to open partway; again to open
completely. Push once to open completely.
Moonroof
Driving position memory (if equipped)

24
FEATURES & OPERATIONS
Control panel
Display
FRONT
Fan speedDriver side
temperature
Rear temperature
Airflow vent
Passenger
temperature
Fan speed Automatic climate control ON
Adjusting the temperature setting will cause
the airflow vents, air intake and
fan to adjust automatically to set temperature. “SYNC” button
Indicator ON: Synchronized temperature settings for
driver, front passenger and rear seats. Indicator OFF:
Separate temperature settings for driver, front passenger
and rear seats.
Air Conditioning ON/OFF
Rear temperature
control ON/OFF
Climate control OFF Windshield defogger
(outside air only)
Temperature selector
(front passenger side)
Temperature selector
(rear passenger area*)
Recirculate cabin air
(outside air when OFF)
Temperature selector
(driver side) Outside rearview mirror**/back
window defogger or windshield
wiper de-icer**
Airflow vent
In “
” mode, use outside
air (“
” indicator “OFF”) to
reduce window fogging.
* To change the rear seat setting, press the “REAR” button.
** If equipped.
Air conditioning/heating

31
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
TOW/HAUL switch
“TOW/HAUL” mode can be used when carrying or towing heavy loads. As fuel
economy is reduced while in “TOW/HAUL” mode, deactivating when driving without
a load is recommended.
Refer to the Owner‘s Manual for more details on this system before attempting to
use it.
System ON/OFF
The Blind Spot Monitor is a system that has two functions:
• The Blind Spot Monitor function (assists the driver in making the decision when to change lanes)
• The Rear Cross Traffic Alert function (assists the driver when backing up)
The system is designed to use radar sensors to detect vehicles traveling\
in the
Sequoia’s blind spot. If a vehicle is detected, the driver will be al\
erted via the
outside rear view side mirror indicators.
Rear Cross Traffic Alert function:
While in reverse, when a vehicle approaching from the right or left rear\
of the
vehicle is detected, the outside rear view mirror indicators flash.
Refer to the Owner‘s Manual for limitations and more details on this system before\

attempting to use it.
Blind Spot Monitor with Rear Cross Traffic
Alert (BSM w/RCTA)
Rear view mirror indicators
Buzzer (RCTA only)

34
Quick overview-Toyota Safety Sense™ P (TSS-P)
Sensors
TSS-P combines an in-vehicle camera mounted in front of the inside rear \
view mirror
and a millimeter-wave radar mounted in the front grille. These sensors s\
upport the
driver assist systems.
Camera sensor
Radar sensor
TOYOTA SAFETY SENSE™
Toyota Safety Sense™ P (TSS-P) is a set of active safety technologies designed
to help mitigate or prevent collisions across a wide range of traffic si\
tuations, in
certain conditions. TSS-P is designed to help support the driver’s aw\
areness,
decision making and vehicle operation contributing to a safe driving exp\
erience.
Refer to the Owner’s Manual for operation, setting adjustments, limitations and
more details to understand these functions and complete safety precautions. For
more information, please go to http://www.toyota.com/safety-sense
Lane Departure Alert (LDA)
LDA is designed to provide notification when the system detects an
unintended lane departure.
Automatic High Beams (AHB)
AHB is designed to detect the headlights of oncoming vehicles and the
tail lights of preceding vehicles and switch between high beams and
low beams as appropriate.
Pre-Collision System with Pedestrian Detection (PCS w/PD)
PCS w/PD is designed to provide alert, mitigation, and/or avoidance
support in certain conditions, when the system detects a potential
collision with a preceding vehicle is likely to occur.
The advanced millimeter-wave radar sensor system is designed to
work with the camera sensor to help recognize a preceding pedestrian,
and provide an alert, mitigation and/or avoidance support in certain
conditions.
Dynamic Radar Cruise Control (DRCC)
DRCC is designed to help maintain a pre-set distance to a preceding
vehicle when the preceding vehicle is traveling at a lower speed.