2020 TOYOTA C-HR light

892. Instrument cluster
2
Instrument cluster
C-HR_OM_USA_OM10634U
The indicators inform the driver of the operating state of the vehicle’s
various systems.
Indicators
IndicatorsPages
Turn signal indicator P. 193
Headlight indicator (U.S.A.) P. 202
Tail light indicator (Canada)P. 202
Front fog light indicator (if equipped) P. 212
Headlight high beam indicatorP. 203
Automatic High Beam indicator P. 207
Parking brake indicator (U.S.A.) P. 194
Parking brake indicator (Canada)P. 194
*1, 2BSM OFF indicator (if equipped)P. 269
*1BSM outside rear view mirror indicator
(on the outside rear view mirrors) (if equipped)P. 269,
278
*2“RCTA OFF” indicator (if equipped) P. 278
Security indicator (on the center panel) P. 81
*1, 3Slip indicator lightP. 287

902. Instrument cluster
C-HR_OM_USA_OM10634U
*1: These lights turn on when the engine switch is turned to the “ON” position
(vehicles without a smart key system) or IGNITION ON mode (vehicles
with a smart key system) to indicate that a system check is being per-
formed. They will turn off after the engine is started, or after a few seconds.
There may be a malfunction in a system if a light does not come on, or if
the lights do not turn off. Have the vehicle inspected by your Toyota dealer.
*2: The light turns on when the system is off.
*3: The light flashes to indicate that the system is operating.
*1, 2VSC off indicatorP. 287
*1, 2PCS warning lightP. 232
*1“AIR BAG ON/OFF” indicator (U.S.A.)
(on the center panel) P. 46
*1“AIR BAG ON/OFF” indicator (Canada)
(on the center panel)P. 46
IndicatorsPages

912. Instrument cluster
2
Instrument cluster
C-HR_OM_USA_OM10634U
*1: These lights turn on when the engine switch is turned to the “ON” position
(vehicles without a smart key system) or IGNITION ON mode (vehicles
with a smart key system) to indicate that a system check is being per-
formed. They will turn off after the engine is started, or after a few seconds.
There may be a malfunction in a system if a light does not come on, or if
the lights do not turn off. Have the vehicle inspected by your Toyota dealer.
*2: The light turns on when the system is operating.
*3: The light flashes to indicate a malfunction.
Indicators and symbols displayed on the multi-information dis-
play
IndicatorsPages
*1, 2, 3Brake hold operated indicator P. 199
*1Brake hold standby indicator P. 199
LDA indicator P. 245
Cruise control indicator P. 252
Cruise control “SET” indicator P. 252
Radar cruise control indicator P. 252
“SPORT” indicator P. 267
“ECO MODE” indicator P. 267
Eco Driving Indicator Light P. 93
Low outside temperature indicator P. 94

922. Instrument cluster
C-HR_OM_USA_OM10634U
Symbols on multi-information displayPages
Charging system warning light P. 421
Low engine oil pressure warning light P. 421
High engine coolant temperature warning light P. 424
Smart key system (if equipped) P. 181
Brake Override System/Drive-Start Control P. 425

932. Instrument cluster
2
Instrument cluster
C-HR_OM_USA_OM10634U
■Eco Driving Indicator Light
Eco Driving Indicator Light will not operate in the following c onditions:
● The shift lever is in anything other than D.
● The vehicle is being driven in “SPORT” mode ( P. 267)
● The vehicle speed is approximately 80 mph (130 km/h) or higher.
During Eco-Friendly acceleration (Eco
driving), Eco Driving Indicator Light will
turn on. When the acceleration exceeds
Zone of Eco driving, and when the vehicle
is stopped, the light turns off.
Eco Driving Indicator Light availability can
be customized. The default setting is on.
(
P. 490)
WARNING
■ If a safety system warning light does not come on
Should a safety system light such as ABS and SRS airbag warning light not
come on when you start the engine, this could mean that these s ystems are
not available to help protect you in an accident, which could r esult in death
or serious injury. Have the vehicle inspected by your Toyota de aler.

962. Instrument cluster
C-HR_OM_USA_OM10634U
The brightness of the instrument panel lights can be adjusted.
Brighter
Darker
■ The meters and display illuminate when
Vehicles without a smart key system:
The engine switch is in the “ON” position.
Vehicles with a smart key system:
The engine switch is in IGNITION ON mode.
■ Outside temperature display
●In the following situations, the correct outside temperature ma y not be dis-
played, or the display may take longer than normal to change.
• When stopped, or driving at low speeds (less than 16 mph [25 k m/h])
• When the outside temperature has changed suddenly (at the entr ance/
exit of a garage, tunnel, etc.)
● If “  ” is displayed continuously, the system may be malfunctioning. Ta k e
your vehicle to your Toyota dealer.
■ Adjusting the clock
The clocks can be adjusted on the audio system screen.
Refer to “MULTIMEDIA OWNER’S MANUAL”.
Instrument panel light control
NOTICE
■To prevent damage to the engine and its components
● Do not let the indicator needle of the tachometer enter the red zone, which
indicates the maximum engine speed.
● The engine may be overheating if the engine coolant temperature gauge
enters the red zone (“H”). In this case, immediately stop the v ehicle in a
safe place, and check the engine after it has cooled completely . (P. 457)

1012. Instrument cluster
2
Instrument cluster
C-HR_OM_USA_OM10634U
●Vehicle Settings
• RCTA setup ( P. 2 8 2 )
*
Select to change the RCTA buzzer volume.
• (Tire pressure warning system) setup ( P. 364)
Select to initialize the tire pressure warning system.
● Meter settings
Select the menu to set up the following items.
• Language
Select to change the language on the display.
•Units
Select to change the unit of measure for fuel consumption.
• (Eco Driving Indicator Light) setup
Select to activate/deactivate the Eco Driving Indicator Light
• Drive information 1 and 2
Select to select up to 2 items that will be displayed on a Driv e informa-
tion screen, up to 2 Drive information screens can be set.
• Pop-up display
Select to enable/disable pop-up displays for incoming call disp lay of the
hands-free phone system.
• Initialisation
Registered or changed meter settings will be deleted or returne d to their
default setting.
*: if equipped

1022. Instrument cluster
C-HR_OM_USA_OM10634U
■Setting items
●“Meter Settings” and “Vehicle Settings” setting items are not s electable
during driving and cannot be operated.
Also, the settings screen is temporarily canceled in the follow ing situations.
• A warning message is displayed.
• The vehicle starts off.
● Settings for functions not equipped to the vehicle are not disp layed.
● When a function is turned off, the related settings for that fu nction are not
selectable.
■ Pop-up display
In some situations, such as when a switch operation is performe d, a pop-up
display will be temporarily displayed on the multi-information display.
■ Liquid crystal display
Small spots or light spots may appear on the display. This phen omenon is
characteristic of liquid crystal displays, and there is no prob lem continuing to
use the display.
■ When disconnecting and reco nnecting battery terminals
The drive information will be reset.
■ Eco Driving Indicator Zone Display
Suggests Zone of Eco driving and Eco
driving ratio based on acceleration.
Zone of Eco driving
Eco driving ratio based on accelera-
tion
If the vehicle exceeds Zone of Eco
driving, the green area disappears
and Eco Driving Indicator Light will
turn off. ( P. 93)