2020 SUZUKI JIMNY Inspection and maintenance

INSPECTION AND MAINTENANCE
0
68PH00732
1) Open the engine hood while the engine is stopped. To remove the bulb holder of the front turn signal light or the front position light (for vehicle with halogen headlights) from the light_ housing, turn the holder counterclockw1se and pull 1t out.
6-49
.(2)
Q(3)
78RB07051
(2) Removal (3) Installation
2) To remove and install the bulb of the front position light (1 ), simply pull out or push in the bulb.
Side turn signal light
78RB07031
Since the bulb is built-in type, replace ii as the light assembly. Remove the light assembly by sliding the light housing left­ward with your finger.

Front fog light (if equipped)
1) Start the engine. Turn the steering
wheel to the opposite side of the b~6 light to be replaced to repla_ce the easily. Then turn off the engine.
2) Remove the clips (1) and screw (2) at
the bottom of bumper. d For removing the clip, use a _flat-blade screwdriver as shown in the ,11ustrat1on.
78RB07033
3) Open the end of the cover inside the fender.
52R70140
4) Disconnect the coupler (3) ~Y1t~~~~:~ the lock release. Turn the u . (4) counterclockwise and remove ,t.
INSPECTION AND MAINTENANCE
Daytime running light (if equipped)
Models without front fog light
78RB07034
6-50

INSPECTION AND MAINTENANCE
Models with front fog light
78RB07035
1) To approach the daytime running light, open the end of the cover inside the front fender. Refer to the procedure for the bulb replacement of the "Front Fog Light" in this section.
6-51
78RB07049
2) Disconnect the coupler by pushing the lock release. Turn the bulb holder coun­terclockwise and remove ii.
NOTE: Depending on the vehicle's specification, the daytime running light is located under the front fog light, but the replace method is same as the above.
Rear combination light
78RB07036
1) Remove the nuts (1) and pull the rear combination light from the rear bumper by pushing the hooks (A).

(2) (4)(5)
78R807037
(2) Brake/tail light (3) Rear turn signal light (4) Reversing light (5) Rear fog light (if equipped)
2) To remove the bulb holder of the above light from the light housing, turn the holder counterclockwise and pull it out.
~~~
(2) / (3) / (4) / (5)~ ,
.. (6) V'
Q(7)
78RB07038
(6) Removal (7) Installation
3) To remove and install the bulb of the brake/tail light (2), the rear turn signal light (3), the reversing light (4), or the rear fog light (5) (if equipped), simply pull out or push in the bulb.
INSPECTION AND MAINTENANCE
License plate light
52RM70070
1) Remove the cover (1) by turning it counterclockwise.
6-52

INSPECTION AND MAINTENANCE
76MH0A126
2) To remove and install the bulb of the license plate light (2), simply pull out or push in the bulb.
High-mount stop light
LED is used. It is recommended that you take your vehicle to a SUZUKI dealer for bulb replacement since special procedures are required.
6-53
Interior light
Remove the lens by using a flat-bladed screwdriver covered with a soft cloth as shown. To install it, simply push it back in.
Front
76MH0A139
Luggage compartment (if equipped)
78RB07039

Wiper blades
54G129
If the wiper blades become brittle or dam­aged, or make streaks when wiping, replace the wiper blades.
To install new wiper blades, follow the pro­cedures below.
NOTICE
To avoid scratching or breaking the window, do not let the wiper arm strike the window while replacing the wiper blade.
NOTE: Some wiper blades may be different from the ones described here depending on vehicle specifications. If so, consult a SUZUKI dealer for proper replacement method.
For windshield wipers:
78RB07040.
1) Hold the wiper arm away from the win­dow.
INSPECTION AND MAINTENANCE
54G130
2) Squeeze lock (1) towards wiper arm (2) and remove the wiper frame from the arm as shown. 3) Unlock the lock end of the wiper blade and slide the blade out as shown.
6-54

INSPECTION AND MAINTENANCE
(Removal)
78RB07045.
(Installation)
a
54G132
6-55
(3) Retainer
4) If the new blade is provided without the two metal retainers, move them from the old blade to the new one. 5) Install the new blade in the reverse order of removal, with the locked end positioned toward the wiper arm. Make sure the blade is properly retained by all the hooks. Lock the blade end into place. 6) Reinstall wiper frame to arm, making sure that the lock lever is snapped securely into the arm.
For rear windshield wipers:
78R807047
(1) Lock end (2) Blade rubber
1) Lift the rear wiper arm a little from the rear window. Remove the wiper frame from the rear wiper arm by pushing the lock end (1) from the side of wiper blade frame and then by pushing the wiper frame to the direction of the arrow with the lock end (1) free from locking in the above illustration.
NOTE: Return the rear wiper arm slowly after removing the rear wiper blade.

77R60050
(3) Stopper (4) Hook (5) Retainer
2) Pull and remove the wiper blade rubber from the wiper frame until the stopper (3) of the wiper frame is taken out of the hook (4). Remove the retainers (5) from the wiper blade.
63R60160
3) If the new blade is provided without the two metal retainers, install them from the old blade to the new one.
,.....,
c
77R60030
4) Install the retainers along the direction of camber as shown in the illustration.
INSPECTION AND MAINTENANCE
63R60180
5) Slide the new wiper blade into the wiper frame. When installing the blade rub­ber, put into the side that has no stop­per on the wiper blade.
6-56