2020 SUZUKI JIMNY AC CON

(For "L/100km" or 11km/L11 setting) To change the unit of average fuel con­sumption, while pushing and holding the trip meter selector knob (1 ), turn the indica­tor selector knob (2).
NOTE:
AVG.
i;11-iu1ookm I..U-1
(Initial setting)
68PH02207
When you change the units that average fuel consumption is displayed in, the instantaneous fuel consumption units will be changed automaticaf/y.
Driving range If you selected driving range the last time you drove the vehicle, the display indicates "---" for a few seconds and then indicates the current driving range when the ignition switch is turned "ON".
The driving range shown in the display is the approximate distance you can drive until the fuel gauge indicates "E", based on current driving conditions.
When the low fuel warning light comes on, the display"---" will appear.
If the low fuel warning light comes on, fill the fuel tank immediately regardless of the value of driving range shown in the display.
When you refuel, the driving range is updated. However, if you only add a small amount of fuel, the correct value will not be displayed.
NOTE: ff you refuel when the ignition switch is in "ON", the driving range may not indicate the correct value. When you reconnect the terminals to the lead-acid battery, the value of driving range will be shown after driving for a while.
BEFORE DRIVING
Fuel gauge
The display (F) shows the fuel gauge.
Refer to "Fuel gauge" in this section.
2-22

•
Turn the indicator selector knob (2).
c:::::> Push the indicator selector knob (2).
NOTE: Depending on vehicle's specifications, some items may not be displayed.
How to use the setting mode: 1) When the ignition switch is "ON" and the vehicle is stationary, push and hold the indicator selector knob (2) until the display shows "[Lo[H". 2) Turn and/or push the indicator selector knob (2) to select a function that you want to set up according to the chart in the previous page. 3) Turn and/or push the indicator selector knob (2) to register settings of the fol­lowing functions.
SEL I I Cl ::J 0 , -::JL C
68PM00272
NOTE: As shown in the above illustration, "SEL" indicates on the display of currently set­ting item. To go back to the higher level display during operation, turn the indicator selector knob (2) to display "bRCH" or " -bR C " and then push the indicator selector knob (2).
Time indication of clock "[L " • [L-t2h: 12-hourformat • CL -2'-lh: 24-hour format
NOTE: Default setting for time indication of clock varies according to the specification.
Additional flashes of the turn signal
"L2" • L2-5L 1: Turn signal flashes three times after the turn signal lever is returned (default set­ting) • L2-5L2: Disable the additional flashes of turn signal
Lighting time of the "To car" function 11 e, :" (if equipped) G t-SL :: Disable the "To car" function c; t-5L2: 10 seconds (default setting) G l-5L3: 15 seconds c; t-SL 'I: 20 seconds G t-5L5: 25 seconds
BEFORE DRIVING
Lighting time of the "To home" function "[,2 11 (if equipped) G2-5L :: Disable the "To home" func-tion C2-5L2: 10 seconds (default setting) G2-5L3: 15seconds G2-5L l/: 20 seconds G2-SLS: 25 seconds G2-5L5: 30 seconds
Tyre pressure monitoring system set­ting (if equipped) UnLRdn: Comfort Mode (default set-ting) • LRdEn : Load Mode
Refer to "Tyre pressure monitoring system (TPMS)" in "OPERATING YOUR VEHI­CLE" section for details.
Initialization setting "dE-a,," • dE-on: Initialize all settings
How to exit the setting mode: Switch the display to show "End" and then push the indicator selector knob (2).
2-24

Speedometer
The speedometer indicates vehicle speed.
Tachometer
The tachometer indicates engine speed in revolutions per minute.
NOTICE
Never drive the vehicle with the engine revving in the red zone or severe engine damage can result. Keep the engine speed below the red zone even when downshifting to a lower gear position. Refer to 11Downshifting maximum allowable speeds" in "OPERATING YOUR VEHICLE" section.
Fuel gauge
(1) ' I
~
~
I
1
-'
(2)
78RB02036
When the ignition switch is "ON", this gauge gives an approximate indication of the amount of fuel in the fuel tank. "F" stands for full and "E" stands for empty. • If the indicator shows only one segment to "E", refill the tank as soon as possible.
If the last segment blinks, it means that the fuel is almost empty. If the low fuel warning light (1) comes on, fill the fuel tank immedi­ately. Refer to "Low fuel warning light" in "Warning and indicator lights" in this sec­tion for details. The mark (2) indicates that the fuel filler door is located on the right side of the vehicle.
BEFORE DRIVING
Brightness control
Brightness
.11111
LO\"/ Hi
52RS20160
~ 10'·16□ MPH ~
(1)
78RB02037
2-26

BEFORE DRIVING
When the ignition switch is turned "ON", the instrument panel lights come on.
Your vehicle has a system to automatically dim the brightness of the instrument panel lights when the position lights or headlights are on.
When the position lights and/or headlights are on, you can adjust the meter illumina­tion brightness.
To increase the brightness of the instru­ment panel lights, turn the indicator selec­tor knob (1) clockwise.
2-27
To reduce the brightness of the instrument panel lights, turn the indicator selector knob (1) counterclockwise.
A WARNING
Do not adjust the brightness of the instrument panel lights while driving. Otherwise, you could lose control of the vehicle.
NOTE: If you do not turn the knob within several seconds, the brightness control display will be cance!ed automatically. When you reconnect the lead-acid bat­tery, the brightness of the instrument panel lights will be reinitialized. Readjust the brightness according to your prefer­ence.
NOTE: If you adjust to the maximum brightness level when the position lights or headlights are on, the following functions will be can­celled. The function which automatically dims the brightness of instrument panel lights The function which operates with the brightness control, except maximum brightness level
Information switch
(if equipped)
You can use the information switch to switch the display indication when the igni­tion switch is in "ON" position and the vehi­cle is stationary.
78RB02099
(1) Information switch (2) Indicator selector knob

To switch to the setting mode 1) Push and hold the information switch (1) when the vehicle is stationary. 2) After the display of setting mode is shown, select the setting item that you want to change by turning the indicator selector knob (2) left or right. Refer to "Setting mode" in this section for details.
NOTE: If you switch to the setting mode while either of the following items is shown on the information display, the current value will be reset. If you do not want to reset its value, push the indicator selector knob (2) quickly beforehand and switch to the other item. Average fuel consumption • Driving time • Average speed
To exit the setting mode 1) To exit the setting mode, select "Back" and push the indicator selector knob (2). 2) Push the information switch (1) quickly.
NOTE: You can exit the setting mode by either of the following operations: Tum the ignition switch to ';,'\CC" or "LOCK" position. • Start driving your vehicle.
Information display
The information display is shown when the ignition switch is in "ON" position.
(A) (B)
(C)
(D) (E) (F)
(G)
(1) Information display
(1)
78RB02033
BEFORE DRIVING
78RB02039
(2) Trip meter selector knob (3) Indicator selector knob
The information display shows the follow­ing information.
Display (A) Clock
Display (B) Thermometer
Display (C) Warning and indicator messages I Fuel consumption / Driving range / Average speed / Driving time Display (D) Selector position (for Automatic transmis­sion models)/ Gear position (for Automatic transmission models) / Gearshift indicator (if equipped)
2-28

BEFORE DRIVING
Display (E) Trip meter I Rear passenger's seat belt reminder (if equipped)
Display (F) Odometer
Display (G) Fuel gauge
52RS20420
When the ignition switch is turned "ON", the message shown in the above illustra­tion will appear on the display for several seconds. Some warning and indicator messages may appear on the display when the igni­tion switch is in "ACC" or "LOCK".
2-29
Clock
When the ignition switch is in "ON", the dis­
play (A) shows the time.
To set the clock, follow "Setting mode" instructions in this section.
,A WARNING
If you attempt to adjust the display while driving, you could lose control of the vehicle. Do not attempt to adjust the display while driving.
Thermometer
When the ignition switch is "ON", the dis­play (B) shows the thermometer. The thermometer indicates the outside temperature.
-3°c
78RB02040
If the outside temperature nears freezing condition, the mark (a) will appear on the display.
NOTE: The outside temperature indication is not the actual outside temperature when driving at low speed, or when stopped. If there is something wrong with the ther­mometer, or just after the ignition switch is turned "ON", the display may not indi­cate the outside temperature.
When the display (C) shows the driving range, you can change the unit of tem­perature. To change the unit of temperature, refer to "Setting mode" in this section.
25°(
77 °F
(Initial setting)
52RM20880

Fuel consumption/ Driving range/ Average speed / Driving time
When there are no warning or indicator messages on the display (C), you can select one of the following indications to appear on the display: instantaneous fuel consumption, average fuel consumption, driving range, average speed, driving time or no indication.
(a)
Instant fuel economy km/L 0 __ 2~uo
t-
(f)
..
(b)
(e)
Average fue! economy
50.0 km/L
Or,vmg t1rne
03:19:21
(c)
(d)
Range
383
Average speed
43
>m
km/h
78RB02041
BEFORE DRIVING
(a) Instantaneous fuel consumption (b) Average fuel consumption (c) Driving range (d) Average speed (e) Driving time (f) No indication
To switch the display indication, push the indicator selector knob (3) quickly.
NOTE: The value of fuel consumption, driving range and average speed shown on the display are affected by the following condi­tions; road condiUon surrounding traffic condition driving condition vehicle condition a malfunction which causes the malfunc­tion indicator light to come on or blink
2-30

BEFORE DRIVING
Instantaneous fuel consumption The display shows instantaneous fuel con­sumption with a bar graph only when the vehicle is moving.
NOTE: The display does not show the bar graph unless the vehicle is moving. Depending on the vehicle's specification, the fuel consumption units of initial set­ting are indicated as U100km, km/L or MPG (UK). The indicated maximum value of instan­taneous fuel consumption is one of the followings. No more than the maximum value will be indicated on the display even if the actual instantaneous fuel consumption is higher. -For U100km setting: 30 -For km/L setting: 50 -For MPG (UK) setting: 80 The indication on the display may be delayed if fuel consumption is greatly affected by driving conditions. The display shows estimated values. Indications may not be the same as actual values.
2-31
Average fuel consumption If you previously selected average fuel consumption setting, the display shows average fuel consumption from the last reset to the present when the ignition switch is turned "ON".
NOTE: When you reconnect the terminals to the lead-acid battery, the value of average fuel consumption will be shown after driving for a period of time.
You can select the timing to reset the value of average fuel consumption by one of the following three methods; Reset after refuel: the value of average fuel consumption will be reset automati­cally by refueling. Reset with trip meter A: the value of average fuel consumption will be reset automatically by resetting trip meter A. Reset manually: the value of average fuel consumption will be reset by push­ing and holding the indicator selector knob (3) when the display indicates the average fuel consumption.
To change the timing to reset the value of average fuel consumption, refer to "Setting mode" in this section.
NOTE: If you add only a small amount of fuel when you select "Reset after refuel", the average fuel consumption value may not be reset.
Driving range If you selected driving range the last time you drove the vehicle, the display indicates "---" for a few seconds and then indicates the current driving range when the ignition switch is turned "ON".
The driving range shown in the display is the approximate distance you can drive until the fuel gauge indicates "E", based on current driving conditions.
When the low fuel warning light comes on, the display "---" will appear.
If the low fuel warning light comes on, fill the fuel tank immediately regardless of the value of driving range shown in the display.
When you refuel, the driving range is updated. However, if you only add a small amount of fuel, the correct value will not be displayed.