2020 SUZUKI GRAND VITARA engine

10-1
GENERAL INFORMATION
54P00-01E
Vehicle identification
Chassis serial number
63J10468LM101
The chassis and/or engine serial numbers
are used to register the vehicle. They are
also used to assist your dealer when
ordering or referring to special service
information. Whenever you have occasion
to consult your SUZUKI dealer, remember
to identify your vehicle with this number.
Should you find the number difficult to
read, you will also find it on the identifica-
tion plate.
Engine serial number
60G128
The engine serial number is stamped on
the cylinder block as shown in the illustra-
tion.
EXAMPLE
EXAMPLE (for some vehicles)

11-1
SPECIFICATIONS
54P00-01E
11
SPECIFICATIONS
NOTE:
Specifications are subject to change without notice.
M/T: Manual transaxle Gasoline: Gasoline engine model
Diesel: Diesel engine model2WD: 2-wheel drive
4WD: 4-wheel drive
ITEM: Dimensions UNIT: mm (in.)
Overall length4175 (164.4)
Overall width1775 (69.9)
Overall height1610 (63.4)
Wheelbase2500 (98.4)
Track Front 1535 (60.4)
Rear 1505 (59.3)
Ground clearance185 (7.3)
ITEM: Mass (weight) UNIT: kg (lbs) GASOLINE ENGINE MODEL DIESEL ENGINE MODEL
Curb mass (weight) 2WD 1075 – 1180 (2370 – 2601) 1230 – 1295 (2712 – 2855)
4WD 1160 – 1245 (2557 – 2745) 1295 – 1360 (2855 – 2998)
Gross vehicle mass (weight) rating 1730 (3814) 1870 (4123)
Permissible maximum axle weight Front 1040 (2293) 1040 (2293)
Rear 910 (2006) 910 (2006)

11-2
SPECIFICATIONS
54P00-01E
ITEM: Engine
Type M16A (DOHC) D16AA (DOHC)
Number of cylinders 4
Bore 78.0 mm (3.07 in.) 79.5 mm (3.12 in.)
Stroke 83.0 mm (3.27 in.) 80.5 mm (3.16 in.)
Piston displacement 1586 cm
3
(1586 cc, 96.8 cu.in)1598 cm3
(1598 cc, 97.5 cu.in)
Compression ratio 11.0 : 1 16.5 : 1
ITEM: Electrical
Standard spark plug
Gasolinewithout ENG A-STOP system DENSO K16HPR-U11
with ENG A-STOP system NGK SILFR6A11
Battery
Gasolinewithout ENG A-STOP system 12V 36Ah 300A(EN)
with ENG A-STOP system 12V 60Ah 540A(EN)
Dieselwithout ENG A-STOP system 12V 60Ah 620A(EN)
with ENG A-STOP system 12V 72Ah 630A(EN)
Fuses See “INSPECTION AND MAINTENANCE” section.

11-5
SPECIFICATIONS
54P00-01E
ITEM: Recommended fuel / lubricants and capacities (approx.)
Fuel See “FUEL RECOMMENDATION” section. 47 L (10.3 Imp gal)
Engine oil
Gasoline
Except
for
MexicoClassification: ACEA A1/B1, A3/B3, A3/B4, A5/B5
API SL, SM or SN
ILSAC GF-3, GF-4 or GF-5
Viscosity: SAE 0W-203.9 L (6.9 Imp pt)
(replacement with oil filter)
For
MexicoEngine oil with “Starburst” symbol
DieselClassification: ACEA C2
Viscosity: SAE 0W-305.65 L (9.9 Imp pt)
(replacement with oil filter)
Engine coolant
Gasoline
“SUZUKI LLC: Super (Blue) Coolant”5.8 L (10.2 Imp pt)
(including reservoir tank)
Diesel5.5 L (9.7 Imp pt)
(including reservoir tank)
Manual transaxle oil 5M/T
“SUZUKI GEAR OIL 75W-80”2.5 L (4.4 Imp pt)
6M/T 2.1 L (3.7 Imp pt)
Transfer oil 4WD “SUZUKI GEAR OIL 75W-85” 0.93 L (1.6 Imp pt)
Rear differential oil 4WD “SUZUKI GEAR OIL 75W-85” 0.8 L (1.4 Imp pt)
Brake fluid / Clutch fluid
SAE J1704 or DOT4Refill to the proper oil level according
to the instructions in “INSPECTION
AND MAINTENANCE” section.

12-4
SUPPLEMENT
54P00-01E
NOTE:
Oxygenated fuels are fuels which contain
oxygen-carrying additives such as MTBE
or alcohol.
If “RON 95” label is attached, you must use
unleaded gasoline with a minimum rating
of 91 pump octane ((R + M)/2 method).
Gasoline containing MTBE
Unleaded gasoline containing MTBE
(methyl tertiary butyl ether) may be used in
your vehicle if the MTBE content is not
greater than 15%. This oxygenated fuel
does not contain alcohol.
Gasoline-ethanol blends
Blends of unleaded gasoline and ethanol
(grain alcohol), also known as gasohol,
may be used in your vehicle if the ethanol
content is not greater than 10%.
Gasoline-methanol blends
Fuels containing 5% or less methanol
(wood alcohol) may be suitable for use in
your vehicle if they contain cosolvents and
corrosion inhibitors. Do not use fuels con-
taining more than 5% methanol under any
circumstances. Fuel system damage or
vehicle performance problems resulting
from the use of such fuels are not the
responsibility of SUZUKI and may not be
covered under the New Vehicle Limited
Warranty.
Fuel pump labeling
In some states, pumps that dispense oxy-
genated fuels are required to be labeled
for the type and percentage of oxygenate
and whether important additives are pres-
ent. Such labels may provide enough infor-
mation for you to determine if a particular
blend of fuels meets the requirements
listed above. In other areas, pumps may
not be clearly labeled as to the content or
type of oxygenate and additives. If you are
not sure that the fuel you intend to use
meets these requirements, check with the
service station operator or the fuel sup-
plier.
NOTE:
To help clean the air, SUZUKI recom-
mends you use the oxygenated fuels.
However, if you are not satisfied with the
driveability or fuel economy of your vehicle
when you are using an oxygenated fuel,
switch back to the regular unleaded gaso-
line.
Engine oil and filter
Specified oil
“Starburst” symbol
80JC103
Use engine oil for gasoline engines with
the above “Starburst” symbol, certified by
American Petroleum Institute.
We highly recommend you use SAE 0W-20
or 5W-30 oil.
SAE 0W-20 is the best choice for good fuel
economy and good starting in cold
weather.
NOTICE
Be careful not to spill fuel containing
alcohol while refueling. If fuel is
spilled on the vehicle body, wipe it up
immediately. Fuels containing alco-
hol can cause paint damage, which is
not covered under the New Vehicle
Limited Warranty.
NOTICE
Failure to use the recommended oil
can result in engine damage.

12-5
SUPPLEMENT
54P00-01E
Tire rotation
4-tire rotation
54G114
To avoid uneven wear of your tires and to
prolong their life, rotate the tires as illus-
trated. Tires should be rotated as recom-
mended in the periodic maintenance
schedule. After rotation, adjust front and
rear tire pressures to the specification
listed on your vehicle’s tire information
label.
For European countries,
Mexico and South Africa
Theft deterrent alarm system
A theft deterrent alarm system is armed in
about 20 seconds after you lock the doors.
Keyless push start system – Use the
remote controller or push the request
switch on driver’s door handle, front pas-
senger’s door handle or tailgate.
Keyless entry system – Use the transmit-
ter.
Once the system is armed, any attempt to
open a door by using any other means (*)
than the keyless push start system remote
controller, the request switch, the keyless
entry system transmitter or engine hood
(for EU specification vehicle) will cause the
alarm to be triggered.
* These means include the following:
–The key
– The lock knob on a door
– The power door locking switchNOTE:
The theft deterrent alarm system gener-
ates alarms when any of the predeter-
mined conditions is met. However, the
system does not have any function of
blocking unauthorized entry into your
vehicle.
Always use the keyless push start sys-
tem remote controller, the request switch
or the keyless entry system transmitter
to unlock the doors when the theft deter-
rent alarm system has been armed.
Using a key instead will trigger the
alarm.
If a person who does not know the theft
deterrent alarm system is going to drive
your vehicle, we recommend you explain
the system and its operation to the per-
son, or disable the system beforehand.
Mistakenly triggering the alarm may
cause a nuisance to others.
Even if the theft deterrent alarm system
is armed, you should still be careful to
guard against theft. Do not leave money
or things of value in your vehicle.

12-6
SUPPLEMENT
54P00-01E
How to arm the theft deterrent alarm
system (when enabled)
Lock all doors (including the tailgate) using
the keyless push start system remote con-
troller, the request switch or the keyless
entry system transmitter. The theft deter-
rent light (1) will start blinking, and the theft
deterrent alarm system will be armed in
about 20 seconds.
While the system is being armed, the indi-
cator continues to blink at intervals of
approximately 2 seconds.
54P000208
NOTE:
To prevent the alarm from being acciden-
tally triggered, avoid arming it while any-
one remains inside the vehicle. The
alarm will be triggered if any person
inside unlocks a door or engine hood (for
EU specification vehicle) by operating
the lock knob or power door locking
switch.
The theft deterrent alarm system is not
armed when all doors are locked using
the key from outside, or using the door
lock knobs or the power door locking
switch from inside.
If any door is not operated within approx-
imately 30 seconds after the doors have
been unlocked using the keyless push
start system remote controller, the
request switch or the keyless entry sys-
tem transmitter, the doors are automati-
cally locked again. At the same time, the
theft deterrent alarm system is armed if
the system is in the enabled state.How to disarm the theft deterrent alarm
system
Simply unlock the doors using the keyless
push start system remote controller, the
request switch or the keyless entry system
transmitter. The theft deterrent light will go
out, indicating that the theft deterrent
alarm system is disarmed.
(1)

12-7
SUPPLEMENT
54P00-01E
How to stop the alarm
Should the alarm be triggered accidentally,
unlock the doors using the keyless push
start system remote controller, the request
switch or the keyless entry system trans-
mitter, or press the engine switch to
change the ignition mode to “ON” or turn
the ignition switch to “ON” position. The
alarm will then stop.
NOTE:
Even after the alarm has stopped, if you
lock the doors using the keyless push
start system remote controller, the
request switch or the keyless entry sys-
tem transmitter, the theft deterrent alarm
system will be rearmed with a delay of
about 20 seconds.
If you disconnect the battery while the
theft deterrent alarm system is in the
armed condition or the alarm is actually
in operation, the alarm will be triggered
or re-triggered when the battery is then
reconnected, although, in the latter case,
the alarm remains stopped for the period
between disconnection and reconnec-
tion of the battery.
Even after the alarm has stopped at the
end of the predetermined operation time,
it will be triggered again if any door or
engine hood (for EU specification vehi-
cle) is opened without disarming the
theft deterrent alarm system.Checking whether the alarm has been
triggered during parking
If the alarm was triggered due to an unau-
thorized entry into the vehicle and you then
press the engine switch to change the igni-
tion mode to “ON” or turn the ignition
switch to “ON” position, the theft deterrent
light will blink rapidly for about 8 seconds
and a buzzer will beep 4 times during this
period. If this happens, check whether your
vehicle has been broken into while you
were away from it.
Enabling and disabling the theft deter-
rent alarm system
The theft deterrent alarm system can be
either enabled or disabled.
When enabled (factory setting)
When the system is enabled, it causes the
hazard warning lights to flash for about 40
seconds if any of the alarm trigger condi-
tions is met. The system also causes the
interior buzzer to beep intermittently for
about 10 seconds, which is followed by
intermittent sounding of the horn for about
30 seconds.
The theft deterrent light continues to blink
during this time.
When disabled
When the system is disabled, it stays dis-
armed even if you perform any system
arming operation.How to switch the state of the theft
deterrent alarm system
You can switch the theft deterrent alarm
system from the enabled state to the dis-
abled state, and vice versa, using the fol-
lowing method.
54P000209
(2)(3)
(1)
EXAMPLE