2020 SUZUKI CELERIO specification

76MH1-74E
1
TABLE OF CONTENTSFUEL RECOMMENDATION1
BEFORE DRIVING2
OPERATING YOUR VEHICLE3
DRIVING TIPS4
OTHER CONTROLS AND EQUIPMENT5
VEHICLE LOADING AND TOWING6
INSPECTION AND MAINTENANCE7
EMERGENCY SERVICE8
APPEARANCE CARE9
GENERAL INFORMATION10
SPECIFICATIONS11
SERVICE NETWORK12
76MH1-74E

0-7
76MH1-74E
EMISSION WARRANTY POLICY
Maruti Suzuki offers the Emission Warranty on all Maruti Suzuki vehicles (apart from the Regular Warranty and will run parallel tothe regular product warranty) only in four metropolitan cities (NewDelhi, Kolkata, Mumbai and Chennai) with effect from July 1st,2001.
Te r m s :The Emission Warranty will be applicable for 80,000 kms or 3years (Whichever comes earlier) from the date of delivery to thefirst owner. The remaining warranty terms will be valid in case ofany change in ownership provided the production of all valid docu-ments.
Conditions:1. Under Emission Waranty, Warranty claims will be admitted fora prima facie examination, in case vehicle fails to meet theEmission Standard as specified in sub rule (2) of rule no. 115of Central Motor Vehicles Rules (CMVR), 1989.
2. The warranty claims will only be accepted after examinationcarried out by Maruti Suzuki or it’s dealer which leads to firmconclusions that thea) Original settings have not been tempered in any case.b) Part (as given in Annexure - A) has a manufacturing defect.c) Vehicle is unable to meet the Emission Standards (as givenin 1.), inspite of the vehicle having been maintained andused in accordance with the instructions as specified inOwner’s Manual and Service Booklet and the used fuel anddifferent oils (Engine oil, Transmission oil, Brake oil etc.) arealso as per specification.
3. The method of examination for deciding the warranty of theparts will be at the sole discretion of Maruti Suzuki and it’sdealer and results of the examination will be final and binding.If after examination, the warrantable condition is not estab-lished, Maruti Suzuki and it’s dealer has the right to charge all,or part of the cost of such examination.
4. Under Emission Warranty, the parts (as given in Annexure - A)will be changed free of cost, but the consumables will becharged as per actual.
5. If the part covered under Emission Warranty or the associatedparts, are not independently replaceable, on account of thesebeing integral parts of a complete assembly, Maruti Suzuki andit’s dealer will have the sole discretion to replace either theentire assembly or by using some of the parts of the systemthrough suitable repairs or modifications.
6. Any consequential repairs or replacement of parts which maybe found necessary to establish compliance of Emission War-ranty, will not be considered under warranty, unless the same isunder product warranty. The consumable will be charged asper actual under such repair or replacement.
7. Maruti Suzuki will not be responsible for the cost of transporta-tion of the vehicle to the nearest Maruti Suzuki dealer work-shop or any loss due to non-availability of the vehicle duringthe period of lodging of a warranty claim and examination and/or repair by Maruti Suzuki dealer.
8. Maruti Suzuki will not be responsible for any penalty that maybe charged by statutory authorities on account of failure tocomply with the EMISSION STANDARDS.
9. Emission Waranty will not be affected on the change of owner,provided all the documents are available.
8

0-8
76MH1-74E
55KS0-74E
10.All maintenance actions (as specified in the Owner’s Manualand Service Booklet) need to be followed and recorded in the manual for emission warranty.
11.The customer needs to produce the PUC (Pollution UnderControl) certificate valid for the period preceeding the testduring which the failure is discovered. The receipts (for themaintenance of the vehicle as per specification in Owner’sManual and Service Booklet from the date of original purchaseof the vehicle) will also be required.
Conditions under which the Emission Warranty is not APPLICABLE
1. In the absence of valid PUC certificate.
2. Vehicle not serviced from Maruti Suzuki authorised workshopas per the schedule specified in the Owner’s Manual.
3. Vehicle subjected to abnormal use (accident, motor race, ral-lies or for the purpose of establishing the records etc).
4. Use of non MGP (Maruti Geniune Part).
5. Vehicle tampered in an unauthorised manner.
6. Tampering with odometer so that the actual kilometer readingcan not be read.
7. Use of adulterated fuel and/or unspecified oils (Engine oil,Transmission oil and Brake oil etc).
Annexure - A
List of parts covered under Emission Warranty 1. Fuel Injection Assembly, Pressure Regulator, Throttle Body
Assembly.
2. Electronic Control Module (ECM).
3. Intake Manifold.
4. EGR valve.
5. Distributor and internal parts.
6. Ignition Coil.
7. Canister Assembly.
8. Vapour Liquid Seperator.
9. Fuel Tank and Filler Cap.
10. PCV (Positive Crankcase Ventilation) Valve.
11. Oil Filler Cap.
12. Catalytic Convertor.
13. Exhaust Manifold.
14. All Fuel Injection System related SENSORS.
15. High Pressure Fuel Pump.
16. Glow Plug.
17. Glow Plug Controller.
9

2-36
BEFORE DRIVING
76MH1-74E
76MH1-74E
NOTE: Depending on vehicle’s specifications,some items may not be displayed.
How to operate the setting mode:1) When the ignition switch is in the

2-37
BEFORE DRIVING
76MH1-74E
76MH1-74E
76MH0017
NOTE: • As shown in the above illustration,“ ” indicates on the display of cur- rently setting item.• To go back to the higher level displayduring operation, turn the indicatorselector knob (2) to display “bACK” or“-bAC” and then push the indicatorselector knob (2).• If the security system “S1” is in the dis-abled state, the shock sensor “S2”, pre-warning sensitivity “S3” and full blastwarning sensitivity “S4” cannot be setup.
5) To exit the setting mode, switch the dis-play to show “End” and then push theindicator selector knob (2).
Warning and Indicator Lights
Brake System Warning Light
65D477
Three different types of operations existdepending on the vehicle’s specification.
1) The light comes on briefly when theignition switch is turned to the “ON” position.2) The light comes on when the parkingbrake is engaged with the ignition switch in the “ON” position.3) The light comes on when under eitheror both of above two conditions.
The light also comes on when the fluid in the brake fluid reservoir falls below the specified level.The light should go out after starting the engine and fully releasing the parking brake, if the fluid level in the brake fluid res-ervoir is adequate. The light also comes on together with the ABS warning light when the rear brakeforce control function (proportioning valve function) of the ABS system fails. If the brake system warning light comes onwhile you are driving the vehicle, it may mean that there is something wrong with
the vehicle’s brake system. If this happens,you should:
1) Pull off the road and stop carefully.
2) Test the brakes by carefully starting andstopping at the side of the road.– If you determine that it is safe, drivecarefully at low speed to the nearest dealer for repairs, or– Have the vehicle towed to the nearestdealer for repairs.
EXAMPLE
WA R N I N G
Remember that stopping distancemay be longer, you may have to push harder on the pedal, and the pedal may go down farther than normal.
WA R N I N G
If any of the following conditions occur, you should immediately ask your MARUTI SUZUKI dealer toinspect the brake system. • If the brake system warning lightdoes not go out after the engine has been started and the parking brake has been fully released.• If the brake system warning lightdoes not come on when the igni-tion switch is turned to the “ON” position.• If the brake system warning lightcomes on at any time during vehi-cle operation.
48

5-22
OTHER CONTROLS AND EQUIPMENT
76MH1-74E
76MH1-74E
Points to remember when making MP3/ WMA/AAC files Common High bit rate and high sampling fre- quency are recommended for high qual- ity sounds. Selecting VBR (Variable Bit Rate) is not recommended. Selecting VBR may cause display of in correct playing time and jumpiness of playback. Playback sound quality varies depending on the encoding environment. Fordetails, refer to the user manual of the encoding software and the writing soft- ware in use.
Recording MP3/WMA/ AAC files on a CD media It is recommended not to write both CD- DA files and MP3/WMA/AAC files on adisc. If both CD-DA files and MP3/WMA/AAC files are on the same disc, tracks maynot be played in the correct order or some tracks may not be played at all.
When storing both MP3 data and WMA data on the same disc, sort and place them in different folders. Do not write files other than MP3/WMA/ AAC files and unnecessary folders on a disc. MP3/WMA/AAC files should be named to meet the standards and the file sys- tem specifications as shown below. The file extension “.mp3”, “.wma” or “.m4a” should be assigned to files based on their format independently. You may encounter a trouble in playing MP3/WMA/AAC files or displaying infor- mation of MP3/WMA/AAC files depend-ing on the writing software or CD recorder in use. This unit does not have a play list func-tion. It is recommended to write discs in Disc- at-Once mode even though Multi-ses-sion mode is supported.
Compression formats MP3 Bit rate: MPEG1 Audio Layer III: 32 k - 320 kbpsMPEG2 Audio Layer III: 8 k - 160 kbps MPEG2.5 Audio Layer III: 8 k - 160 kbps Sampling frequency: MPEG1 Audio Layer III: 32 k/44.1 k/ 48 kHz MPEG2 Audio Layer III: 16 k/22.05 k/24 kHz MPEG2.5 Audio Layer III: 8 k/11.025 k/ 12 kHz
WMA (Ver. 7, Ver. 8, Ver. 9*) Bit rate: CBR 32 k - 320 kbps Sampling frequency: 32 k/44.1 k/48 kHz* WMA 9 Professional/LossLess/Voice are not supported.
AAC* Bit rate: ABR 16k - 320 kbbs Sampling frequency: 32 k/44.1 k/48 kHz* Apple Lossless is not supported.
Supported file systems ISO 9660 Level 1/Level 2, Joliet, Romeo
Maximum number of files/folders Maximum number of files: 512 Maximum number of files in a folder: 255 Maximum depth of tree structure: 8 Maximum number of folders: 255 (Root folder is included.)
NOTICE
Never assign the “.mp3”, “.wma”, or “.m4a” file name extension to a file ifit is not in th e MP3/WMA/AAC format file. Failure to observe this may result in damage to the speaker due tonoise production.
107

7-10
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
5) Tighten the filter specified turn from the point of contact with the mounting sur- face (or to the spec ified torque) using an oil filter wrench.
Tightening torque for oil filter Petrol engine: 1 turn or 14 Nm (1.4 kg-m, 10.3 lb-ft)Diesel engine: 3/4 turn or 14 Nm (1.4 kg-m, 10.3 lb-ft)
Refill with Oil and Check for Leaks1) Pour oil through the filler hole andinstall the filler cap. For the approximate capacity of the oil, refer to the “CAPACITIES” item in the “SPECIFICATIONS” section.2) Start the engine and look carefully for leaks at the oil filter and drain plug. Run the engine at various speeds for at least5 minutes.
3) Stop the engine and wait about 5 min- utes. Check the oil level again and add oil if necessary. Check for leaks again.
Engine Coolant
Selection of CoolantTo maintain optimum performance anddurability of your engine, use MARUTIGenuine Coolant or equivalent. This type of coolant is best for your cooling system as it: Helps maintain proper engine tempera- ture. Gives proper protection against freezingand boiling. Gives proper protection against corro- sion and rust.Failure to use the proper coolant can dam- age your cooling system. Your authorized
MARUTI SUZUKI dealer can help you select the proper coolant.
Coolant Level CheckCheck the coolant level at the reservoirtank, not at the radiator. With the engine cool, the coolant level should be betweenthe “FULL” and “LOW” marks.
NOTICE
To tighten the oil filter properly, it isImportant to accurately identify theposition at which the filter gasket first contacts the mounting surface.
NOTICE
To prevent oil leakage, make sure that the oil filter is tight, but do notover-tighten it.
NOTICE
• When replacing the oil filter, it is rec-ommended that you use a Marutigenuine replacement filter. If you use an after market filter, make sure it is of equivalent quality and followthe manufacturer’s instructions. • Oil leaks from around the oil filter or drain plug indicate incorrectinstallation or gasket damage. If you find any leaks or are not sure that the filter has been properlytightened, have the vehicle inspected by your MARUTI SUZUKI dealer.
NOTICE
To avoid damaging your cooling sys- tem: • Always use a high quality ethyleneglycol base non-silicate type cool- ant diluted with distilled water at the correct mixture concentration.• Make sure that the proper mix is 50/ 50 coolant to distilled water (Die- sel) and 30/70 (Petrol). Concentra-tions greater than this may cause overheating conditions. • Neither use 100% coolant nor 100%Plain water. • Do not add extra inhibitors or addi- tives. They may not be compatiblewith your cooling system. • Do not mix different types of base coolants. Doing so may result inaccelerated seal wear and/or the possibility of severe overheating and extensive engine damage.
148

7-13
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
78K179 60G160S 60B307
Spark plug gap “a” NGK KR6A-10: 0.95 – 1.05 mm (0.037 – 0.041 in.)NOTICE
• When pulling the ignition coils out,do not pull on the cable. Pulling onthe cable can damage it. • When servicing the iridium/plati- num spark plugs (slender centerelectrode type plugs), do not touch the center electrode, as it is easy to damage.
Correct Wrong
EXAMPLE
NOTICE
• When installing the spark plugs,screw them in with your fingers to avoid stripping the threads. Tighten with a torque wrench to 17.5 Nm (1.8 kg-m, 12.9 lb-ft). Donot allow contaminants to enter the engine through the spark plug holes when the plugs are removed.• Never use spark plugs with the wrong thread size.
Loosen
Tighten
NOTICE
When replacing spark plugs, you should use the brand and type speci-fied for your vehicle. For the speci- fied plugs, refer to the “SPECIFICATIONS” section at theend of this book. If you wish to use a brand of spark plug other than the specified plugs, consult your MAR-UTI SUZUKI dealer.
151