2020 SUZUKI CELERIO stop start

7-7
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
(For Diesel Engine Model)
76MH024
(1) Preferred
Be sure that the engine oil you use comes under the quality classification of ACEAA5/B5-10. Select the appropriate oil vis- cosity according to the above chart.
Oil Level Check
76MH030
(1) Engine oil dipstick (Petrol engine) (2) Engine oil dipstick (Diesel engine)
It is important to keep the engine oil at the correct level for proper lubrication of yourvehicle’s engine. Check the oil level with the vehicle on a level surface. The oil level indication may be inaccurate if the vehicleis on a slope. The oil level should be checked either before starting the engine or at least 5 minutes after stopping theengine.
The handle of the engine oil dipstick is col- ored yellow for easy identification.
52D084
Pull out the oil dipstick, wipe oil off with aclean cloth, insert the dipstick all the way into the engine, then remove it again. Theoil on the stick should be between the upper and lower limits shown on the stick. If the oil level indication is near the lowerlimit, add enough oil to raise the level to the upper limit.
(1)
-30
-22 -4 14 32 50 68 86 104
-20 -10 10 20 30 40 0
5W-30
(1)
(2)
EXAMPLE
NOTICE
Failure to check the oil level regularly could lead to serious engine trouble due to insufficient oil.
EXAMPLEUpper Lower
145

7-8
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
Refilling
81A147
Remove the oil filler cap and pour oil slowly through the filler hole to bring the oil level to the upper limit on the dipstick. Be careful not to overfill. Too much oil is almost asbad as too little oil. After refilling, start the engine and allow it to idle for about a min- ute. Stop the engine, wait about 5 minutesand check the oil level again.
Changing Engine Oil and FilterDrain the engine oil while the engine is stillwarm.
76MH037
(1) Engine oil filler cap (Petrol engine)(2) Engine oil filler cap (Diesel engine)
1) Remove the oil filler cap. 2) Place a drain pan under the drain plug.3) Using a wrench, remove the drain plug and drain out the engine oil.
68KH068
Tightening torque for drain plug (1):Petrol engine: 35 Nm (3.6 kg -m, 25.8 lb-ft) Diesel engine: 35 Nm (3.6 kg -m, 25.8 lb-ft)
NOTICE
(For Diesel Engine Model) Do not top up the oil over the MAX limit. Too much oil causes serious engine trouble.
Close Open
EXAMPLE
CAUTION
The engine oil temperature may behigh enough to burn your fingers when the drain plug is loosened. Waituntil the drain plug is cool enough to touch with your bare hands.
(2)
(1)
Open Close
EXAMPLE
WA R N I N G
New and used oil can be hazardous.Children and pets may be harmed by swallowing new or used oil. Keepnew and used oil and used oil filters away from children and pets. Repeated, prolonged contact withused engine oil may cause skin can- cer. Brief contact with used oil may irri-tate skin. (Continued)
(1)
EXAMPLE
146

7-10
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
5) Tighten the filter specified turn from the point of contact with the mounting sur- face (or to the spec ified torque) using an oil filter wrench.
Tightening torque for oil filter Petrol engine: 1 turn or 14 Nm (1.4 kg-m, 10.3 lb-ft)Diesel engine: 3/4 turn or 14 Nm (1.4 kg-m, 10.3 lb-ft)
Refill with Oil and Check for Leaks1) Pour oil through the filler hole andinstall the filler cap. For the approximate capacity of the oil, refer to the “CAPACITIES” item in the “SPECIFICATIONS” section.2) Start the engine and look carefully for leaks at the oil filter and drain plug. Run the engine at various speeds for at least5 minutes.
3) Stop the engine and wait about 5 min- utes. Check the oil level again and add oil if necessary. Check for leaks again.
Engine Coolant
Selection of CoolantTo maintain optimum performance anddurability of your engine, use MARUTIGenuine Coolant or equivalent. This type of coolant is best for your cooling system as it: Helps maintain proper engine tempera- ture. Gives proper protection against freezingand boiling. Gives proper protection against corro- sion and rust.Failure to use the proper coolant can dam- age your cooling system. Your authorized
MARUTI SUZUKI dealer can help you select the proper coolant.
Coolant Level CheckCheck the coolant level at the reservoirtank, not at the radiator. With the engine cool, the coolant level should be betweenthe “FULL” and “LOW” marks.
NOTICE
To tighten the oil filter properly, it isImportant to accurately identify theposition at which the filter gasket first contacts the mounting surface.
NOTICE
To prevent oil leakage, make sure that the oil filter is tight, but do notover-tighten it.
NOTICE
• When replacing the oil filter, it is rec-ommended that you use a Marutigenuine replacement filter. If you use an after market filter, make sure it is of equivalent quality and followthe manufacturer’s instructions. • Oil leaks from around the oil filter or drain plug indicate incorrectinstallation or gasket damage. If you find any leaks or are not sure that the filter has been properlytightened, have the vehicle inspected by your MARUTI SUZUKI dealer.
NOTICE
To avoid damaging your cooling sys- tem: • Always use a high quality ethyleneglycol base non-silicate type cool- ant diluted with distilled water at the correct mixture concentration.• Make sure that the proper mix is 50/ 50 coolant to distilled water (Die- sel) and 30/70 (Petrol). Concentra-tions greater than this may cause overheating conditions. • Neither use 100% coolant nor 100%Plain water. • Do not add extra inhibitors or addi- tives. They may not be compatiblewith your cooling system. • Do not mix different types of base coolants. Doing so may result inaccelerated seal wear and/or the possibility of severe overheating and extensive engine damage.
148

8-6
EMERGENCY SERVICE
76MH1-74E
76MH1-74E
If the Starter Does Not
Operate
1) Try turning the ignition switch to the “START” position with the headlights turned on to determine the battery con- dition. If the headlights go excessivelydim or go off, it usually means that either the battery is flat or the battery terminal contact is poor. Recharge thebattery or correct battery terminal con- tact as necessary. 2) If the headlights remain bright, checkthe fuses. If the reason for failure of the starter is not obvious, there may be a major electrical problem. Have the vehi-cle inspected by your authorized MAR- UTI SUZUKI dealer.
If the Engine is Flooded
If the engine is flooded with petrol, it may be hard to start. If this happens, press theaccelerator pedal all the way to the floor and hold it there while cranking the engine. For petrol engine model, do not operatethe starter motor for more than 12 sec- onds. For diesel engine model, do not operatethe starter motor for more than 30 sec- onds.
If the Engine Overheats
The engine could overheat temporarily under severe driving conditions. If the highengine coolant temperature warning light comes on as overheating during driving: 1) Turn off the air conditioner, if equipped.2) Take the vehicle to a safe place and park. 3) Let the engine run at the normal idlespeed for a few minutes until the high engine coolant temperature warning light goes off.
If the high engine coolant temperature warning light does not go off: 1) Turn off the engine and check that the water pump belt and pulleys are notdamaged or slipping. If any abnormality is found, correct it.
2) Check the coolant level in the reservoir. If it is found to be lower than the “LOW” line, look for leaks at the radiator, waterpump, and radiator and heater hoses. If you locate any leaks that may have caused the overheating, do not run theengine until these problems have been corrected. 3) If you do not find a leak, carefully addcoolant to the reservoir and then the radiator, if necessary. (Refer to “Engine Coolant” in the “INSPECTION ANDMAINTENANCE” section.)
NOTE: If your engine overheats and you are unsure what to do, contact your MARUTI SUZUKI dealer.
WA R N I N G
If you see or hear escaping steam,stop the vehicle in a safe place andimmediately turn off the engine to let it cool. Do not open the hood when steam is present. When the steamcan no longer be seen or heard, open the hood to see if the coolant is still boiling. If it is, you must wait until itstops boiling before you proceed.
176