2020 SUZUKI ALTO length

2776G-74E
BEFORE DRIVING
3-14
ww ww
w WARNING
To Adjust the Belt
Pull the shoulder portion of the belt
upwards through the tongue plate.
The length of the diagonal shoulder strap
adjusts itself to allow freedom of movement.
The seat belt has an emergency locking
retractor (ELR), which is designed to lock
the seat belt only during a sudden stop or
impact.
No modifications or additions of any
sort should be made to the seat belt
or its operating mechanism.
76G-03-035
Seat Belt Inspection
Periodically inspect the seat belts to make
sure they work properly and are not
damaged. Check the webbing, buckles, latch
plates, retractors, anchorages and guide
loops. Replace any seat belts which do not
work properly or are damaged.
76G-03-036
To unfasten the belt, press the release
button on the buckle catch.
76G-03-034

28
76G-74E
BEFORE DRIVING3-15
To lengthen, release the tounge from the
buckle unit, pull the tounge (adjuster) in
the direction of the arrow, at right angles
to the belt. The tounge should then be
refitted into the buckle unit and the belt
tightened as previously described.
76G-03-038
NOTE:To identify the center seat belt buckle catchand tongue in the rear seat, "CENTER" is
moulded on the buckle catch and tongue ofthe center lap belt. The buckle catches aredesigned so a buckle tongue can not be
inserted into the wrong buckle catch.
76G-03-039
On this belt the adjuster is incorporated in
the tounge unit.
To tighten the belt, pull the free end of
the belt across alongside the lap strap
until it is adjusted to a snug comfortable
position.LAP BELT (if equipped)
76G-03-037

10376G-74E
76G-09-020
ALTO K10EXAMPLE
To access the spark plugs,
For Alto
1. Disconnect the coupler while pushing the
release lever,
2. Remove the bolts, and
3. Pull the spark plug boots.
For Alto K10
1. Unclamp and remove the air cleaner case.
2. If necessary, disconnect the coupler (1) while pushing the release lever.
3. Remove the ignitor bolts.
4. Pull the spark plug boots out.
CAUTION
76G-09-021
Spark Plug gap "a"
Alto - 0.85 ± 0.5 mm
Alto K10 - 1.0 ± 0.05 mm
INSPECTION AND MAINTENANCE
9-20
ALTO
EXAMPLE When disconnecting the spark plugcables, pull on the boot, not on the
cable itself. Pulling on the cable can
damage it.
When installing the spark plugs, screw them in with your fingers to
avoid stripping the threads. Tighten
with a torque wrench to :
Alto - 13.0–22.0 N-m (1.3–2.2 kg-m,
9.4–15.9 lb-ft)
Alto K10 - 25 N-m (2.5 kg-m, 18.0
lb-ft).
Do not allow contaminants to enter
the engine through the spark plug
holes when the plugs are removed.
Never use spark plugs with the
wrong thread size or length.
CAUTION
When replacing spark plugs, you
should use the brand and type
specified for your vehicle. For the
specified plugs, refer to the
“SPECIFICATIONS” section at the end
of this book.NOTE:
When installation, make sure the wires,couplers, sealing rubber of top cover and
washers, are correctly returned in place.

13576G-74E
SPECIFICATIONS
13
SPECIFICATIONSNOTE:Specifications are subject to change without notice.
ITEM: DIMENSIONS UNIT:mm
ALTO (STD / Lx / Lxi) ALTO K10 (Lxi / Vxi)
Overall length 34953620
Overall width 14751495/1475 (without side moulding)
Overall height 14601460
Wheelbase 23602360
Tread front 1295 1295
rear 1290 1290
Ground clearance 160160
ITEM: MASS (WEIGHT) UNIT:Kg
ALTO (STD / Lx / Lxi) ALTO K10 (Lxi / Vxi)
Kerb mass (weight) 690-705750-765
Gross vehicle mass (weight) rating 11401185
Seating Capacity 5 persons5 persons
ITEM: ENGINE ALTO (STD / Lx / Lxi)ALTO K10 (Lxi / Vxi)
Type F8DK10B
Number of cylinders 33
Bore 68.573
Stroke 72.079.5
Piston displacement 796 cc998 cc
Compression ratio 9.2 ± 0.2 : 110.0 ± 0.4 : 1
13-1