2020 SUBARU BRZ light

2PURPOSE OF THIS GUIDE
4ENTRY AND EXIT
6INSTRUMENT PANEL
8GETTING COMFORTABLE
15CONTROLS
20GAUGES AND WARNING LIGHTS
21OPERATING THE VEHICLE
24REFUELING
25PASSENGER/CARGO AREAS
28ENGINE COMPARTMENT
30ADDITIONAL SPECIFICATIONS
31INDEX
TABLE OF CONTENTS

KEYLESS ENTRY
1Lock/Arm
• Pressing this button will lock both doors and activate the
security alarm.
• If either door is not fully closed, a continuous tone will
sound.
• Pressing this button three times (within five seconds) will
activate the vehicle finder function. If you are within 30 feet
of your Subaru, the horn will sound once, and the hazard
warning flashers will flash three times.
2Unlock/Disarm
• Pressing this button once will unlock the driver’s door.
• Pressing this button twice (within five seconds) will unlock
both doors.
• When you press this button, the interior lights will illuminate, if set to the “DOOR”
positions.
3Trunk
• Pressing and holding this button will unlock the trunk.
4Panic Alarm
• Pressing and holding this button will sound the horn and flash the hazard warning
lights.
• Press any button on the access key fob or transmitter to deactivate.
KEYLESS ACCESS WITH PUSH BUTTON START
Unlock Using Door Handles
Grip the driver’s door handle to unlock the driver’s
door. Grip the passenger’s handle to unlock both
doors. Two chirps will sound and the hazard warning
flashers will flash twice.
Transmitter
ENTRY AND EXIT
4

1Power windows (p. 11)
2Power exterior mirrors (p. 9)
3Instrument panel switches (p. 18)
4Audio Controls (p. 15)
5Light controls (p. 16)
6Gauges and warning lights (p. 20)
7Multi-Information Display Control Switches (p. 15)
8Windshield wipers (p. 18)
INSTRUMENT PANEL
6

REAR VIEW MIRROR
Auto-dimming Mirror(if equipped)
When driving at night, the auto-dimming function
senses brightness from vehicle headlights behind you
and automatically dims to reduce glare. Pressing the
switch will turn this function on or off. A green LED
indicator on the switch will illuminate when the
function is on.
HomeLink®5 Accessory Mirror(if equipped)
The HomeLink®5 accessory mirror provides three
buttons to replace up to three hand-held radio
frequency remotes used to activate devices, such as
garage door openers, gate openers, entry door locks,
security systems and home lighting. Please see the
Owner’s Manual for programming instructions or visit
www.subaru.com/homelink to view a how-to video.
NOTE: HomeLink
®5 may not be compatible with some older door
openers or additional equipment may be required.
GETTING COMFORTABLE
10

Operation in Automatic Mode
1Automatic Control Button:This system automatically controls all of the climate
systems except defogging. Press “AUTO” to activate. Press “OFF” to turn off the
system.
2Temperature Control Dial:Turn the dial clockwise to increase the temperature or
counterclockwise to decrease the temperature. The temperature will appear on the
screen. You can adjust separate temperature settings for the driver’s side and
passenger’s side.
3Dual Button:Press the button to activate or deactivate the dual mode. Dual mode
makes it possible to have separate temperature settings for the driver’s side and
passenger’s side.
When using automatic mode, the fan speed, airflow distribution, air-inlet control and air
conditioning compressor are controlled automatically. To activate:
1. Press the “AUTO” button. The “FULL AUTO” indicator light illuminates on the climate
control display.
2. Set the preferred temperature using the temperature control dial.
If you operate any of the buttons other than “OFF”, rear window defogger, DUAL or the
temperature control dial, the “FULL” indicator light will turn off. The “AUTO” light will
remain illuminated. You can then manually control the system as desired. Press the
“AUTO” button to change back to “FULL AUTO” mode.
Operation in Manual Mode
4Recirculated/Outside Air Button:Press this to prevent outside air from entering
your Subaru. Press the button again to allow outside air into your Subaru. NOTE: To
prevent windshield fogging, do not remain in the recirculated mode for an extended
period of time.
5Fan Speed Control Dial:Turn the fan speed control dial to increase or decrease fan
speed.
6Airflow Mode Selection Button:Press the button to select the desired airflow mode.
The selected mode – ventilation, bi-level, feet or feet-defrost – is shown on the
display.
GETTING COMFORTABLE
12

CRUISE CONTROL
1RES:To resume your speed after
canceling, push the lever up to the “RES”
side.
2CANCEL:To cancel the cruise control,
pull the lever toward you, push the brake
pedal or press the “ON-OFF” button. If
you have a manual transmission, you can
push in the clutch pedal.
3SET:Press the accelerator pedal until your vehicle reaches the desired speed. Push
the lever down to the “SET” side and release. Ease off the accelerator pedal. Your
vehicle will maintain the desired speed.
4ON/OFF:To activate the cruise control, press the “ON-OFF” button. The cruise
control indicator light on the instrument panel will turn on. To deactivate cruise
control, press the “ON-OFF” button again.
Increase speed
Push the lever up to the “RES” side; hold until your vehicle reaches the desired speed and
release. To increase speed using the accelerator pedal, press the pedal until you reach the
desired speed. Push the lever down to the “SET” side to set the speed.
Decrease speed
Push the lever down to the “SET” side; hold until your vehicle slows to the desired speed
and release. To decrease the speed using the brake pedal, press the pedal to release
cruise control temporarily. When the speed decreases to the desired speed, push the lever
down to the “SET” side to set the speed.
LIGHT CONTROLS
1AUTO:If equipped, rotate the end of the
lever to automatically turn your headlights
on or off, depending on the level of
outside light.
2Daytime Running Lights:Rotate the end
of the lever to turn on the instrument
panel lights, parking lights, side marker
lights, tail lights, and license plate lights.
3Headlights:Rotate the end of the lever to
turn on the headlights, instrument panel
lights, parking lights, side marker lights,
tail lights, and license plate lights.
CONTROLS
16

4High Beams:Push the lever forward to change from low beam to high beam. Pull the
lever back to center to return to low beam. If equipped, this also activates the High
Beam Assist (HBA) system.
5Fog Lights:If equipped, rotate the dial to turn on the fog lights.
Illumination Brightness
While the light switch is on, rotating the dial on
the instrument panel upward will make the
illumination brighter. When the dial is fully
rotated upward (dots aligned), the instrument
panel illumination stays at full brightness.
Rotating the dial downward dims the
instrument panel illumination.
For map equipped vehicles this setting also
affects the day/night view and illumination
level.
Daytime Running Lights
The daytime running lights automatically turn on when the engine has started, the parking
brake is fully released, the light switch is in the Off, “AUTO” (if equipped) or “
”
position, and the select lever is not in the “P” position. Always turn on the headlights when
it’s dark outside by rotating the dial to the “
” or “AUTO” position.
TURN SIGNALS
Push slightly up for right lane change or fully
up for right turn signal. Push slightly down for
left lane change or fully down for left turn
signal.
CONTROLS
17

OVERHEAD PANEL
1Interior Light Switch
2Light
CONTROLS
19