2020 Seat Leon lock

Operation
Unlock the seat backrest with the
cor d.  V
alid for: LEON Sportstourer Fig. 119
In the luggage compartment: levers to
unl ock the r
ear backrest.

Operation
USB power sockets
Depending on the equipment and the coun-
try, the v ehicl
e may also have USB connec-
tions exclusively for charging or as a power
socket.
These USB ports are located at the rear of
the console, between the front seats . These
connectors can work at a maximum power of
up to 10.5 W per port.
They are not intended for file playback.
230 volt power socket*
With the engine running, the power socket
››› Fig. 148 activates automatically as soon
as a connector is plugged in. If there is
enough power available, the socket can still
be used while the engine is off ››› Connect an electrical device: Open the co
v-
er and insert the plug int
o the power socket
as far as possible to unlock the built-in child
lock. The socket only supplies power once
the child lock is unlocked. LED on the power socket
Steady green
light: The childproof lock is unlocked.
The sock
et is r

eady to operate. LED on the power socket
Flashing green
light: The ignition is switched off, but
ther
e is enough po

wer available
to continue supplying the socket
with current for a maximum of 10
minutes. If the connector is un-
plugged before this time elap-
ses, the socket is disconnected
and cannot be used again until
the ignition is switched on again.
Flashing red
light: There is an anomaly, e.g. dis-
connection due t
o a curr

ent
surge or overheating. Disconnection due to overheating
When the t
emper

ature exceeds a certain val-
ue, the 230 volt socket inverter is automati-
cally disconnected. The disconnection pre-
vents overheating when the power consump-
tion of the connected devices is excessive or
the ambient temperature is very high. The
230-volt power supply can be used once
again after a cooling time. First unplug the
connector of the connected device and then
plug it back in again. This prevents the elec-
trical device from being switched on again if
this is not wanted. WARNING
The electrical system is under high voltage!

Driving
Driving
St ar
t and driving
Starting and stopping the
engine Ignition and start button Fig. 161
In the lower part of the centre console:
st art butt

on. The engine can be started with a start button
(Pr
ess & Driv

e). For this there must be a valid
key inside the passenger compartment.
Opening the driver's door when exiting the
vehicle activates the electronic lock on the
steering column if the ignition is disabled. Switching the ignition on/off
If you only want t

o switch on the ignition
(without starting the engine), briefly press the
start button once without pressing the brake
pedal or the clutch pedal ››› .
The  


 push-button text flashes
lik e a heartbeat when the syst

em is ready for
the ignition to be turned on or off.
Automatic ignition disconnection
When the vehicle detects that there is no
driver once the engine has stopped, after a
certain time the ignition is switched off auto-
matically. If at that time the dipped beam
headlights are on, the side lights will stay on
for approx. 30 minutes. The side lights can be
turned off by blocking the vehicle
››› page 103, or manually
››› page 120
.
Automatic deactivation of the ignition on
vehicles with the Start-Stop system
The ignition is switched off automatically
when the vehicle is stopped and the auto-
matic engine shutdown is active, if:

Driving
 – P
arking l ock
When the P button is pressed, the drive
wheels are locked. Only press P when the ve-
hicle is stationary ››› .
T o pr

ess the P button you must press the
brake pedal simultaneously.
 – Reverse gear
Reverse gear must be engaged only when
the vehicle is stationary and the engine is
idling ››› .
T o engage r

everse gear R, you must press the
brake pedal simultaneously. The reverse
lights switch on when the reverse gear R is
selected and the ignition is on.
 – Neutral
In this position, the gear is in neutral.
Press the brake pedal to move the lever from
N to D/S when the vehicle is stationary or at
speeds below 3 km/h (2 mph) ››› .
 – P
ermanent f

orward drive position
The D/S position enables the gears to be op-
erated in normal mode (D) or sport mode (S).
To select Sport mode S, move the lever back-
wards. Pushing the lever again will select nor-
mal mode D. The selected driving mode is
displayed on the instrument panel screen.
In normal mode (D), the gearbox selects the
best gear ratio. This depends on the engine load, the road speed and the dynamic gear
control pr

ogramme (DCP).
Sport mode (S) should be selected for a
sporty driving style. This setting makes use of
the engine's maximum power output. When
accelerating the gear shifts will be noticea-
ble.
Under certain circumstances (e.g. on moun-
tain roads) it can be advantageous to switch
tiptronic mode ››› page 231
, to adapt the
gears to suit the road conditions.
Selector lever lock
In N, the lever lock prevents a gear range
from being engaged, and prevents the vehi-
cle from moving off accidentally.
Press and hold the brake pedal with your left
foot with the engine running.
As a reminder to the driver, when the lever is
in position N the following indication will be
shown on the screen:
When stationary, apply footbrake
while selecting a gear.
The lever is not locked if it is moved quickly
through position N (e.g. when shifting from R
to D). This makes it possible, for instance, to
“rock the vehicle backwards and forwards” if
it is stuck in snow or mud. The lever lock en-
gages automatically if the brake pedal is not
pressed and the lever is in position N for more than about one second at a speed of less
than 5 km/h (3 mph). WARNING

Driving
Steering Inf ormation r
elating to different ve-
hicle processes. Electro-mechanical power steering adapts
el
ectr

onically to the speed of the car, torque
and steering angle.
Even if the power steering fails or the engine
is stopped, it is possible to continue to rotate
the steering wheel as long as the key remains
in the ignition, but more force must be ap-
plied.
Progressive steering
Depending on the vehicle’s features, it may or
may not incorporate a progressive steering
system.
In city traffic you do not need to turn so much
on parking, manoeuvring or in very tight turns.
On the road or on the motorway, progressive
steering transmits, for example, in bends, a
sportier, more direct and noticeably more dy-
namic driving sensation. Control lamp v
It lights up red
Faulty steering.
Do not continue driving, stop the v
ehicle as soon as
possible and in a safe manner.
Take the vehicle to a specialised workshop and have
the fault repaired as soon as possible. v
It lights up yellow
Limited steering operation.
Driv e car

efully to a specialised workshop to have the
steering checked.
If the warning light does not come on again after re-
starting the engine and driving a short distance, it is
not necessary to check the steering.
OR: The 12-v olt batt
ery was disconnected and re-
connected.
Drive a short distance at 15-20 km / h (9-12 mph). v
It flashes yellow
The steering column is jammed.
When st opped, t

urn the steering wheel in both direc-
tions.
OR: The st eering column does not unlock or lock.
T
urn off the ignition and turn it on again. Consider the
messages shown on the instrument panel display.
Do not continue driving if the steering column re-
mains locked after switching on the ignition. Seek
specialist assistance. The control lamp should light up for a few
seconds when the ignition is s
wit

ched on. It
should go out once the engine is started. WARNING
Never ignore the warning lamps or messag-
es.

Driving
system itself, the rear and side environment of
the v ehicl
e using the rear sensors
››› page 242. It detects moving objects that
approach from behind, such as cars
››› Fig. 193.
If a critical situation is detected when the
door is opened, it will be alerted by an acous-
tic signal on the door speaker of the corre-
sponding side ››› Fig. 194
. Additionally, the
control lamp of the lane departure warning of
the corresponding door will flash. If the door
has already been opened and another road
user has been detected in a critical situation,
the control lamp of the lane departure warn-
ing on the corresponding side will light up
permanently.
The brightness of the door opening warning
indication cannot be adjusted.
When you want to access the vehicle for the
first time, with the doors closed and locked,
the function will be available 3 minutes after
the first opening of any of the doors. The
function will continue to be available as long
as the vehicle has the ignition connected and
is not moving.
After switching off the ignition, the function
will remain available for approximately 3 mi-
nutes. After that time, the control lamps will
light up indicating the deactivation of the
function. WARNING

Braking and parking
Brake assist systems Electronic Stability Control (ESC)
The ESC helps t
o impr
ove safety. It reduces
the tendency to skid and improves the stabili-
ty and roadholding of the vehicle. The ESC
detects critical handling situations, such as
vehicle understeer or oversteer, or wheelspin
on the driving wheels. It stabilises the vehicle
by braking individual wheels or by reducing
the engine torque. The warning lamp will
flash on the instrument panel when the ESC is
intervening !.
The ESC includes the anti-lock brake system
(ABS), the hydraulic brake assist (HBA), the
traction control system (TCS), electronic dif-
ferential lock (EDS), electronic torque control
(XDS) and the tractor-trailer sway mitiga-
tion*.
ESC also helps stabilise the vehicle by
changing the torque.
The TCS can be deactivated when wheel
spin is desirable ››› page 281
.
Anti-lock brake system (ABS)
ABS prevents the wheels from locking up un-
der braking until the vehicle has reached a
virtual standstill. You can continue to steer the
vehicle even when the brakes are on full.
Keep your foot on the brake pedal and do not
pump the brakes. You will feel the brake pedal
pulsate while the ABS is working. If the running gear or brake system is modi-
fied, the eff
ectiv

eness of the ABS could be se-
verely limited.
Hydraulic Brake Assist (HBA)
The brake assist system can reduce the re-
quired braking distance. The braking force is
automatically boosted if you press the brake
pedal quickly in an emergency. You must
keep pressing the brake pedal until the dan-
ger has passed.
Traction control (TCS)
In the event of the wheels spinning, the TCS
reduces the engine torque to adapt to the
road condition. This helps the car to start
moving, accelerate or climb a gradient.
Electronic differential lock (EDL)
When the EDL detects wheelspin, it brakes
the spinning wheel and directs the power to
the other driven wheel. This function is active
up to approximately 100 km/h (62 mph).
To prevent the disc brake of the braked wheel
from overheating, the EDL cuts out automati-
cally if subjected to excessive loads. The ve-
hicle can still be driven. The EDL will switch on
again automatically when the brake has
cooled down. Tractor-trailer sway mitigation*
If the vehicl
e is pulling a trailer, it will control
the following: tractor-trailers tend to sway.
When the swaying of the trailer is felt by the
vehicle and detected by the ESC, it will auto-
matically brake the towing vehicle within the
limits of the system and mitigate the sway.
Tractor-trailer sway mitigation is not available
in all countries ››› page 303
.
Electronic engine torque management
(XDS)
When taking a curve, the driveshaft differen-
tial allows the outer wheel to turn at a higher
speed than the inner wheel. In this way, the
wheel that is turning faster (outer wheel) re-
ceives less drive torque than the inner wheel.
This may mean that in certain situations the
torque delivered to the inner wheel is too
high, causing the wheels to spin. On the other
hand, the outer wheel is receiving a lower
drive torque than it could transmit. This can
cause a loss of grip on the drive axle, in this
case the front axle, which results in under-
steer or “lengthening” of the trajectory.
The XDS can detect and correct this effect
via the sensors and signals of the ESC.
Via the ESC, the XDS will brake the inside
wheel and counter the excess driving torque
of that wheel. This means that the requested
trajectory is much more precise. »
279

High-voltage battery
Charging process display  V
alid for: hybrid vehicles Fig. 211
Behind the cover of the battery charg-
ing sock et: char
ging process display Fig. 212
On the inside of the cover of the bat-
t ery char

ging socket: sticker with information
on the charging process display. An LED light on the charging socket
› ›

› Fig. 211 (arrow) shows the status of the
charging process.
A sticker on the battery charging cover pro-
vides information on the meaning of the LEDs
››› Fig. 212.
charging process displays:
Green LED ››› Fig. 212
:
Always on: Charge completed success-
fully.
Turn signals: The high-voltage battery is
charging.
1 2 Short flashes: Programmed charging is
activ
e

. The charging process has not yet
started.
Yellow LED ››› Fig. 212
:
Turn signals: The parking lock P has not
been enabled.
Always on: No electrical network has
been detected. Arrange an inspection of
the power supply and network. Seek pro-
fessional assistance.
Red LED ››› Fig. 212
:
Turn signals: Error in the charging system.
The charging process cannot start or has
paused.
Always on: The charging connector has
not been locked. Unplug the charging
connector and plug it back in to the
charging socket, making sure it is proper-
ly inserted. If the problem persists, check
the compatibility of the cable or ask a
professional for help.
Charging socket lighting
In the dark, the charging socket's side lighting
(white LED) can facilitate orientation in the
vehicle:
Ignition