2020 Seat Leon ignition

Start and driving
When the ignition is on/off, the engine start
butt on fl
ashes. With the ignition is switched
off, the start button goes off after a few sec-
onds.
With the engine running, the start button light
stays on, indicating that the engine is running.
The time elapsed between the moment the
user starts the engine with the start button
and the lighting changes from flashing to
fixed will depend on specific engine size
characteristics. When the start button is used
to stop the engine, the button starts flashing
again.
In vehicles with the Start-Stop system, the
“My Beat” function also offers additional in-
formation:

Driving
 – P
arking l ock
When the P button is pressed, the drive
wheels are locked. Only press P when the ve-
hicle is stationary ››› .
T o pr

ess the P button you must press the
brake pedal simultaneously.
 – Reverse gear
Reverse gear must be engaged only when
the vehicle is stationary and the engine is
idling ››› .
T o engage r

everse gear R, you must press the
brake pedal simultaneously. The reverse
lights switch on when the reverse gear R is
selected and the ignition is on.
 – Neutral
In this position, the gear is in neutral.
Press the brake pedal to move the lever from
N to D/S when the vehicle is stationary or at
speeds below 3 km/h (2 mph) ››› .
 – P
ermanent f

orward drive position
The D/S position enables the gears to be op-
erated in normal mode (D) or sport mode (S).
To select Sport mode S, move the lever back-
wards. Pushing the lever again will select nor-
mal mode D. The selected driving mode is
displayed on the instrument panel screen.
In normal mode (D), the gearbox selects the
best gear ratio. This depends on the engine load, the road speed and the dynamic gear
control pr

ogramme (DCP).
Sport mode (S) should be selected for a
sporty driving style. This setting makes use of
the engine's maximum power output. When
accelerating the gear shifts will be noticea-
ble.
Under certain circumstances (e.g. on moun-
tain roads) it can be advantageous to switch
tiptronic mode ››› page 231
, to adapt the
gears to suit the road conditions.
Selector lever lock
In N, the lever lock prevents a gear range
from being engaged, and prevents the vehi-
cle from moving off accidentally.
Press and hold the brake pedal with your left
foot with the engine running.
As a reminder to the driver, when the lever is
in position N the following indication will be
shown on the screen:
When stationary, apply footbrake
while selecting a gear.
The lever is not locked if it is moved quickly
through position N (e.g. when shifting from R
to D). This makes it possible, for instance, to
“rock the vehicle backwards and forwards” if
it is stuck in snow or mud. The lever lock en-
gages automatically if the brake pedal is not
pressed and the lever is in position N for more than about one second at a speed of less
than 5 km/h (3 mph). WARNING

Driving
Steering Inf ormation r
elating to different ve-
hicle processes. Electro-mechanical power steering adapts
el
ectr

onically to the speed of the car, torque
and steering angle.
Even if the power steering fails or the engine
is stopped, it is possible to continue to rotate
the steering wheel as long as the key remains
in the ignition, but more force must be ap-
plied.
Progressive steering
Depending on the vehicle’s features, it may or
may not incorporate a progressive steering
system.
In city traffic you do not need to turn so much
on parking, manoeuvring or in very tight turns.
On the road or on the motorway, progressive
steering transmits, for example, in bends, a
sportier, more direct and noticeably more dy-
namic driving sensation. Control lamp v
It lights up red
Faulty steering.
Do not continue driving, stop the v
ehicle as soon as
possible and in a safe manner.
Take the vehicle to a specialised workshop and have
the fault repaired as soon as possible. v
It lights up yellow
Limited steering operation.
Driv e car

efully to a specialised workshop to have the
steering checked.
If the warning light does not come on again after re-
starting the engine and driving a short distance, it is
not necessary to check the steering.
OR: The 12-v olt batt
ery was disconnected and re-
connected.
Drive a short distance at 15-20 km / h (9-12 mph). v
It flashes yellow
The steering column is jammed.
When st opped, t

urn the steering wheel in both direc-
tions.
OR: The st eering column does not unlock or lock.
T
urn off the ignition and turn it on again. Consider the
messages shown on the instrument panel display.
Do not continue driving if the steering column re-
mains locked after switching on the ignition. Seek
specialist assistance. The control lamp should light up for a few
seconds when the ignition is s
wit

ched on. It
should go out once the engine is started. WARNING
Never ignore the warning lamps or messag-
es.

Driver assistance systems
Activate or deactivate the dodge and turn
assist ant
The dodge and t
urn assistance systems can
be activated or deactivated in the infotain-
ment system using the function button  > Driver assistance > Front Assist
››› page 96.
The system will store the setting for the next
time the ignition is switched on.
SEAT recommends having the dodge and
turn assistance systems activated except in
the exceptions described in section
››› page 253.
Deactivating Front Assist temporarily in
the following situations
In the following situations the Front Assist
should be deactivated due to the system's
limitations:

Driving
system itself, the rear and side environment of
the v ehicl
e using the rear sensors
››› page 242. It detects moving objects that
approach from behind, such as cars
››› Fig. 193.
If a critical situation is detected when the
door is opened, it will be alerted by an acous-
tic signal on the door speaker of the corre-
sponding side ››› Fig. 194
. Additionally, the
control lamp of the lane departure warning of
the corresponding door will flash. If the door
has already been opened and another road
user has been detected in a critical situation,
the control lamp of the lane departure warn-
ing on the corresponding side will light up
permanently.
The brightness of the door opening warning
indication cannot be adjusted.
When you want to access the vehicle for the
first time, with the doors closed and locked,
the function will be available 3 minutes after
the first opening of any of the doors. The
function will continue to be available as long
as the vehicle has the ignition connected and
is not moving.
After switching off the ignition, the function
will remain available for approximately 3 mi-
nutes. After that time, the control lamps will
light up indicating the deactivation of the
function. WARNING

Driving
ignition, the function will remain on the next
time the ignition is s wit
ched on.
If the Auto Hold function was not switched on,
it will automatically remain off next time the
ignition is engaged.
The Auto Hold function connects automat-
ically if the following conditions are met
(all points must be met at the same time
››› ):
The v ehicl

e is kept stationary with the
brake pedal on a flat surface or on a
slope.
The engine rotates “correctly”.
The Auto Hold function is automatically
turned off if the following conditions are
met: If any of the conditions mentioned on
››› page 277, Conditions for keeping
the vehicle stationary with the Au-
to Hold function are no longer met.
If the engine is running irregularly or an
anomaly is detected.
If the engine stalls.
Manual gearbox: The clutch and the ac-
celerator are pressed at the same time.
Automatic gearbox: If the accelerator is
pressed
Automatic gearbox: If any of the tyres
has only minimal contact with the
1.
2.
1.
2.
3.
4.
5. ground, e.g. in the case of axle articula-
tion. WARNING
The smart technology incorporated into
the Aut o Hol

d function cannot defy the
laws of physics; it only works within the lim-
its of the system. The greater convenience
provided by the Auto Hold function should
never tempt you to take any risk that may
compromise safety.

Help with parking and manoeuvring
Visual indication segments Fig. 203
Parking aid view on the Infotainment
syst em displ
ay. The optical indication of the segments works
as f
oll

ows:
Grey segments: the obstacle is more
than approx. 30 cm away from the path
or in the direction opposite to travel.
They are also displayed when the elec-
tronic parking brake is activated.
Yellow segments: the obstacles lie on
the vehicle’s path and are at a distance
of less than approx. 30 cm away.
Red segments: obstacles are less than
approx. 30 cm away.
A wake will indicate the anticipated forward
or backward trajectory, depending on the en-
gaged gear. –
–
– If an obstacle is located in the vehicle’s way,
the corresponding audibl

e warning will
sound.
When the penultimate segment is displayed,
the vehicle has reached the collision zone. In
the collision zone, the obstacles are repre-
sented in red (including those out of the
path). Stop the vehicle! ››› in Introduction
on page 290, ››

› in Introduction on
page 290 !
Setting the indications and audio
signal s The indications and acoustic signals are set
in the Inf
ot

ainment system: function button 
> Driver assistance> Parking aid: Setup
Automatic activa-
tion On/off
Front volume* Volume in the front and rear
area.
R

ear volume* Volume in the rear area.
Adjust volume When the parking aid is
s
wit

ched on, the volume of
the audio source will be re-
duced, depending on the se-
lected option. Error messages
If a an error or fault message appears on the
instrument clust
er in P

ark Assist, there is a
fault.
If the fault doesn't disappear before discon-
necting the ignition, it will not be indicated
next time the parking aid is connected.
If a rear sensor is faulty, only the obstacles in
the areas A and
B are displayed
› ›

› Fig. 202. If a front sensor is faulty, only the
obstacles in the areas C and
D will be dis-
pl ayed. Symbol

High-voltage battery
Charging process display  V
alid for: hybrid vehicles Fig. 211
Behind the cover of the battery charg-
ing sock et: char
ging process display Fig. 212
On the inside of the cover of the bat-
t ery char

ging socket: sticker with information
on the charging process display. An LED light on the charging socket
› ›

› Fig. 211 (arrow) shows the status of the
charging process.
A sticker on the battery charging cover pro-
vides information on the meaning of the LEDs
››› Fig. 212.
charging process displays:
Green LED ››› Fig. 212
:
Always on: Charge completed success-
fully.
Turn signals: The high-voltage battery is
charging.
1 2 Short flashes: Programmed charging is
activ
e

. The charging process has not yet
started.
Yellow LED ››› Fig. 212
:
Turn signals: The parking lock P has not
been enabled.
Always on: No electrical network has
been detected. Arrange an inspection of
the power supply and network. Seek pro-
fessional assistance.
Red LED ››› Fig. 212
:
Turn signals: Error in the charging system.
The charging process cannot start or has
paused.
Always on: The charging connector has
not been locked. Unplug the charging
connector and plug it back in to the
charging socket, making sure it is proper-
ly inserted. If the problem persists, check
the compatibility of the cable or ask a
professional for help.
Charging socket lighting
In the dark, the charging socket's side lighting
(white LED) can facilitate orientation in the
vehicle:
Ignition