2020 Seat Ateca light

Lights
Setting 2
All seats occupied, luggage compart-
ment full. With trailer and minimum
dr
awbar l
oad.
Setting 3 Driver only, luggage compartment full
Driving with trailer and maximum
drawbar l
oad. Dynamic headlight range control
The control is not mounted in vehicl
es with
dynamic headlight r

ange control. The head-
light range is automatically adjusted accord-
ing to the vehicle load status when they are
switched on. WARNING
Heavy objects in the vehicle may mean
that the headlights dazzle and distract oth- er drivers. This coul d r

esult in a serious ac-
cident.

Operation
Knob Function
 Turns off the interior lights.
 Turning the interior lights on or off.
Central po- sitionor
 a) The interior lights come on automati-
cally when you unl
ock the vehicle
,
open a door or r
emove the key from
the ignition.
The light goes out a few seconds after
closing all the doors, when locking the
vehicle or connecting the ignition.
* /
 Turning the reading light on and off a)
Depending on version.
Gl o
ve compar
tment and luggage com-
par

tment lighting*
When opening and closing the glove com-
partment on the front passenger side and the
rear lid, the respective light will automatically
switch on and off.
Footwell lighting*
The lights in the footwell area below the dash
(driver and front passenger sides) will switch
on when the doors are opened and will de-
crease in intensity while driving. This intensity
setting can be changed through the infotain-
ment system menu (key  > SETTINGS >
lIGHTING > Interior lighting

Operation
Regularly clean dirt that has become encrus-
t ed on the headlights, e
.g., remains of insects.
T o ensur
e the headlight washers work cor-
rectly in winter, clean away any snow that
may be present on the jet covers located on
the bumper. If necessary, remove ice with an
anti-ice spray. Note

Transport and practical equipment
LED on the power socket
Flashing green
light: The ignition is switched off, but
there is enough power av
ail
able
to continue supplying the socket
with current for a maximum of 10
minutes. If the connector is un-
plugged before this time elap-
ses, the socket is disconnected
and cannot be used again until
the ignition is switched on again.
Flashing red
light: There is an anomaly, e.g. dis-
connection due to a current
surge or o
v

erheating. Disconnection due to overheating
When the t
emper
atur
e e

xceeds a certain val-
ue, the 230 volt socket inverter is automati-
cally disconnected. The disconnection pre-
vents overheating when the power consump-
tion of the connected devices is excessive or
the ambient temperature is very high. The
230-volt power supply can be used once
again after a cooling time. First unplug the
connector of the connected device and then
plug it back in again. This prevents the elec-
trical device from being switched on again if
this is not wanted. WARNING
The electrical system is under high voltage!

Air conditioning
Radio-operated remote control Fig. 157
Auxiliary heating: radio-operated re-
mot e contr ol
. Fig. 157
Swit
ch the auxiliary heat er on
S wit
ch the auxiliary heater off
Control lamp
If the buttons of the remote control are press-
ed unnecessarily, it could switch on the auxili-
ary heater involuntarily, even when it is out of
range or when the control lamp is flashing.
To switch on and off the independent heating,
the button must be pressed and held for ap-
proximately 1 second.
Control lamp on the remote control
When the buttons are pressed, the control
lamp on the remote control 1 provides the
user with diff er
ent inf ormation:


1 It lights up for approx. 2 seconds

Start and driving
In this scenario, the light of the  

  button stays lit
1)
.
When the ignition is s wit
ched on, the St art
-
St
op function is automatically activated.
In the Easy Connect system you can find
more information about the Start-Stop sys-
tem: press the button  > View > Vehicle
status .
Vehicles with a manual gearbox

Driving
the lever is removed from the tiptronic posi-
tion.
Hill Descent Control (HDC)
Control lamps  Valid for vehicles: 4Drive all-wheel drive
k
It lights up white
Hill Descent Control is active. k
It lights up grey
Hill Descent Control is not active. The system is
switched on, but is not adjusting. Some control and warning lamps will light up
briefly when the ignition is s
wit
ched on t o
check cert ain functions. They will s
witch off
after a few seconds. WARNING
Observe the safety warnings

Driving
Fig. 271 : The syst em is oper
ational,
the highlight ed line 1 indicates that
ther e w
as a risk of inv olunt
arily cr
ossing
the lane line and that the steering is be-
ing adjusted to correct the angle.
Fig. 271 : The two highlighted lines 1and
2 light up simultaneously when
both l ane lines ar
e recognised and the
L ane Assist function is activ

ated.
Operating mode Steering wheel vibration
The f
oll
owing sit
uations can cause vibr

ation
in the steering wheel and require the driver to
take active control of driving: