2020 NISSAN GT-R child restraint

The ELR locks the seat belt when the
vehicle slows down rapidly or during
impacts.
The Automatic Locking Retractor (ALR)
mode or child restraint mode locks the
seat belt for child restraint installation.
When the ALR mode is activated the seat
belt cannot be extended again until the
seat belt tongue is detached from the
buckle and fully retracted. The seat belt
returns to the ELR mode after the seat
belt is fully retracted.
(

vehicle’s seat belt (not the lower anchors)
to install the child restraint. Be sure to
follow the child restraint manufacturer’s
instructions for installation.LATCH lower anchor

are they to be used to attach adult
seat belts, or other items or equip-
ment to the vehicle. Doing so could
damage the child restraint an-
chorages. The child restraint will not
be properly installed using the da-
maged anchorage, and a child could
be seriously injured or killed in a
collision.REAR-FACING CHILD RESTRAINT
INSTALLATION USING LATCHRefer to all Warnings and Cautions in the
“Child safety” and “Child restraints” sec-
tions before installing a child restraint.
Do not use the lower anchors if the
combined weight of the child and the
child restraint exceeds 65 lbs (29.5 kg). If
the combined weight of the child and the
child restraint is greater than 65 lbs (29.5
kg), use the vehicle’s seat belt (not the
lower anchors) to install the child re-
straint. Be sure to follow the child re-
straint manufacturer’s instructions for
installation.
Follow these steps to install a rear-facing
child restraint using the LATCH system:
1. Position the child restraint on the seat.Always follow the child restraint man-
ufacturer’s instructions.

7. Check to make sure the child restraintis properly secured prior to each use. If
the child restraint is loose, repeat
steps 1 through 6.

driving and avoid using vehicle
features or taking other actions
that could distract you.
. ALWAYS use your seat belts and
appropriate child restraint sys-
tems. Pre-teen children should
be seated in the rear seat.
. ALWAYS provide information
about the proper use of vehicle
safety features to all occupants
of the vehicle.
. ALWAYS review this Owner’s Man-
ual for important safety informa-
tion.
MODIFICATION OF YOUR VEHICLEThis vehicle should not be modified.
Modification could affect its perfor-
mance, safety or durability, and may
even violate governmental regulations.
See the 2020 NISSAN GT-R Warranty
Information Booklet for details includ-
ing applicable exclusions.

accident.
. Be sure the seat belt tongue is
securely fastened to the proper
buckle.
. Do not wear the seat belt inside
out or twisted. Doing so may
reduce its effectiveness.
. Do not allow more than one
person to use the same seat belt.
. Never carry more people in the
vehicle than there are seat belts.
. If the seat belt warning light
glows continuously while the
ignition is turned ON with all
doors closed and all seat belts
fastened, it may indicate a mal-
function in the system. It is re-
commended you have the system
checked by a GT-R certified
NISSAN dealer.
. No changes should be made to
the seat belt system. For exam-
ple, do not modify the seat belt,
add material, or install devices
that may change the seat belt
routing or tension. Doing so may
affect the operation of the seat
belt system. Modifying or tam-
pering with the seat belt system
may result in serious personal injury.
. Once a seat belt pretensioner has
activated, it cannot be reused and
must be replaced together with
the retractor. It is recommended
you see a GT-R certified NISSAN
dealer.
. Removal and installation of the
pretensioner system components
should be done by a GT-R certi-
fied NISSAN dealer.
. All seat belt assemblies, including
retractors and attaching hard-
ware, should be inspected after
any collision by a GT-R certified
NISSAN dealer. NISSAN recom-
mends that all seat belt assem-
blies in use during a collision be
replaced unless the collision was
minor and the belts show no
damage and continue to operate
properly. Seat belt assemblies
not in use during a collision
should also be inspected and
replaced if either damage or im-
proper operation is noted.
. All child restraints and attaching
hardware should be inspected
after any collision. Always follow
the restraint manufacturer’s in- spection instructions and repla-
cement recommendations. The
child restraints should be re-
placed if they are damaged.

The ELR locks the seat belt when the
vehicle slows down rapidly or during
impacts.
The Automatic Locking Retractor (ALR)
mode or child restraint mode locks the
seat belt for child restraint installation.
When the ALR mode is activated the seat
belt cannot be extended again until the
seat belt tongue is detached from the
buckle and fully retracted. The seat belt
returns to the ELR mode after the seat
belt is fully retracted.
(

vehicle’s seat belt (not the lower anchors)
to install the child restraint. Be sure to
follow the child restraint manufacturer’s
instructions for installation.LATCH lower anchor