
963-2. Opening, closing and locking the doors and trunk
etc. Clean the lock sensor and attempt to 
operate it again.
●A sudden handle operation or a handle 
operation immediately after entering the 
effective range may prevent the doors 
from being unlocked. Touch the door 
unlock sensor and check that the doors 
are unlocked before pulling the door 
handle again.
●Unlocking the vehicle may take more 
time if another electronic key is within the 
effective range.
■When the vehicle is not driven for 
extended periods
●To prevent theft of the vehicle, do not 
leave the electronic key within 6 ft. (2 m) 
of the vehicle.
●The smart access system with push-but-
ton start can be deactivated in advance.
■To operate the system properly
●Make sure to carry the electronic key 
when operating the system. Do not get 
the electronic key too close to the vehicle 
when operating the system from the out-
side of the vehicle.
Depending on the position and holding 
condition of the electronic key, the key may 
not be detected correctly and the system 
may not operate properly. (The alarm may 
go off accidentally, or the door lock pre-
vention function may not operate.)
●Do not leave the electronic key inside the 
trunk. 
The key confinement prevention function 
may not operate, depending on the loca-
tion of the key (close to a spare tire [if 
equipped], the inside edge of the trunk), 
conditions (inside a metal bag, close to 
metallic objects) and the radio waves in 
the surrounding area. ( P.93)
■If the smart access system with 
push-button start does not operate 
properly
●Locking and unlocking the doors and 
opening the trunk:  P.306
●Starting the engine:  P.307
■Customization
Some functions can be customized.  (
 P.341)
■If the smart access system with 
push-button start has been deactivated 
in a customized setting
●Locking and unloc king the doors and 
opening the trunk: 
Use the wireless remote control or 
mechanical key. ( P.86, 90, 306)
●Starting the engine and changing engine 
switch modes: P.307
●Stopping the engine:  P.126
WARNING
■Caution regarding interference with 
electronic devices
●People with implantable cardiac pace-
makers, cardiac resynchronization 
therapy-pacemakers or implantable 
cardioverter defibrillators should keep 
away from the smart access system 
with push-button start antennas. 
( P.93)
The radio waves may affect the opera-
tion of such devices.  If necessary, the 
entry function can be disabled. Ask 
your Lexus dealer for details, such as 
the frequency of radio waves and tim-
ing of the emitted radio waves. Then, 
consult your doctor to see if you 
should disable the entry function.
●Users of any electrical medical device 
other than implantable cardiac pace-
makers, cardiac resynchronization 
therapy-pacemakers or implantable 
cardioverter defibrillators should con-
sult the manufacturer of the device for 
information about its operation under 
the influence of radio waves.
Radio waves could have unexpected 
effects on the operation of such medi-
cal devices.
Ask your Lexus dealer for details on dis-
abling the entry function. 

1584-5. Using the driving support systems
■Enabling/disabling the pre-colli-
sion system
The pre-collision system can be 
enabled/disabled on   ( P.69) of 
the multi-information display.
The system is automatically enabled each 
time the engine switch is turned to IGNI-
TION ON mode.
If the system is disabled, the PCS warn-
ing light will turn on and a message will 
be displayed on the multi-information 
display.
■Changing the pre-collision warn-
ing timing
The pre-collision warning timing can 
be changed on   ( P.69) of the 
multi-information display.
The operation timing  setting is retained 
when the engine switch is turned off.
1Far
The warning will begin to operate earlier 
than with the default timing.
2Middle
This is the default setting.
3Near
WARNING
●When inspecting the vehicle using a 
drum tester such as a chassis dyna-
mometer or speedometer tester, or 
when using an on vehicle wheel bal-
ancer
●When a strong impact is applied to the 
front bumper or front grille, due to an 
accident or other reasons
●If the vehicle cannot be driven in a sta-
ble manner, such as when the vehicle 
has been in an accident or is malfunc-
tioning
●When the vehicle is driven in a sporty 
manner or off-road
●When the tires are not properly 
inflated
●When the tires are very worn
●When tires of a size other than speci-
fied are installed
●When tire chains are installed
●When a compact spare tire or an 
emergency tire puncture repair kit is 
used
●If equipment (snow plow, etc.) that may 
obstruct the radar sensor or camera 
sensor is temporarily installed to the 
vehicle
Changing settings of the pre-col-
lision system 

1644-5. Using the driving support systems
■Vehicle sway warning function
When the vehicle is swaying or 
appears as if it may depart from its lane 
multiple times, the warning buzzer 
sounds and a message is displayed on 
the multi-information display to alert 
the driver.
WARNING
■Before using LDA system
Do not rely solely upon the LDA system. 
The LDA system does not automatically 
drive the vehicle or reduce the amount of 
attention that must be paid to the area in 
front of the vehicle. The driver must 
always assume full responsibility for driv-
ing safely by paying careful attention to 
the surrounding conditions and operat-
ing the steering wheel to correct the path 
of the vehicle. Also, the driver must take 
adequate breaks when fatigued, such as 
from driving for a long period of time.
Failure to perform  appropriate driving 
operations and pay careful attention may 
lead to an accident, resulting in death or 
serious injury.
■To avoid operating LDA system by 
mistake
When not using the LDA system, use the 
LDA switch to turn the system off.
■Situations unsuitable for LDA system
Do not use the LDA system in the follow-
ing situations.
The system may not operate properly 
and lead to an accident, resulting in 
death or serious injury.
●A spare tire, tire chains, etc. are 
equipped.
●When the tires have been excessively 
worn, or when the tire inflation pres-
sure is low.
●Tires which differ by structure, manu-
facturer, brand or tread pattern are 
used.
●Objects or patterns that could be mis-
taken for white (yellow) lines are pres-
ent on the side of the road (guardrails, 
curbs, reflective  poles, etc.).
●Vehicle is driven on a snow-covered 
road.
●White (yellow) lines are difficult to see 
due to rain, snow, fog, dust, etc. 

2576-3. Do-it-yourself maintenance
6
Maintenance and care
RC300Check if the treadwear indicators are 
showing on the tires. Also check the 
tires for uneven wear, such as excessive 
wear on one side of the tread.
Check the spare tire condition and 
pressure if not rotated.
New tread
Worn tread
Treadwear indicator
The location of treadwear indicators is 
shown by a “TWI” or “ ” mark, etc., 
molded into the sidewall of each tire.
Replace the tires if the treadwear indica-
tors are showing on a tire.
WARNING
■When adding washer fluid
Do not add washer fluid when the engine 
is hot or running as washer fluid contains 
alcohol and may catch  fire if spilled on 
the engine, etc.
NOTICE
■Do not use any fluid other than 
washer fluid
Do not use soapy water or engine anti-
freeze instead of washer fluid.
Doing so may cause streaking on the 
vehicle’s painted surfaces, as well as 
damaging the pump leading to problems 
of the washer fluid not spraying.
■Diluting washer fluid
Dilute washer fluid with water as neces-
sary.
Refer to the freezing temperatures listed 
on the label of the washer fluid bottle.
Tires
Replace or rotate tires in accor-
dance with maintenance schedules 
and treadwear.
Checking tires
A
B
C 

2596-3. Do-it-yourself maintenance
6
Maintenance and care
Vehicles with front and rear tires of 
the same size
Rotate the tires in the order shown.
To equalize tire wear and extend tire life, 
Lexus recommends that tire rotation is car-
ried out at the same in terval as tire inspec-
tion.
Do not fail to initialize the tire pressure 
warning system after tire rotation.
Vehicles with front and rear tires of 
differing sizes
Tires cannot be rotated.
■When rotating the tires
Make sure that the engine switch is off. If the 
tires are rotated while the engine switch is in 
IGNITION ON mode, the tire position 
WARNING
■When inspecting or replacing tires
Observe the following precautions to 
prevent accidents.
Failure to do so may cause damage to 
parts of the drivetrain as well as danger-
ous handling characteristics, which may 
lead to an accident  resulting in death or 
serious injury.
●Do not mix tires of different makes, 
models or tread patterns.
Also, do not mix tires of remarkably 
different treadwear.
●Do not use tire sizes other than those 
recommended by Lexus.
●Do not mix differently constructed 
tires (radial, bias-b elted or bias-ply 
tires).
●Do not mix summer, all season and 
snow tires.
●Do not use tires that have been used 
on another vehicle.
Do not use tires if you do not know 
how they were used previously.
●Do not tow if your vehicle has a com-
pact spare tire installed.
NOTICE
■Low profile tires
Low profile tires may cause greater dam-
age than usual to the tire wheel when 
sustaining impact from the road surface. 
Therefore, pay attention to the following:
●Be sure to use proper tire inflation 
pressure. If tires are under-inflated, 
they may be damaged more severely.
●Avoid potholes, uneven pavement, 
curbs and other road hazards. Failure 
to do so may lead to severe tire and 
wheel damage.
■If tire inflation pressure of each tire 
becomes low while driving
Do not continue driving, or your tires 
and/or wheels may be ruined.
■Driving on rough roads
Take particular care when driving on 
roads with loose surfaces or potholes.
These conditions may cause losses in tire 
inflation pressure, reducing the cushion-
ing ability of the tires. In addition, driving 
on rough roads may cause damage to 
the tires themselves, as well as the vehi-
cle’s wheels and body.
Tire rotation 

2646-3. Do-it-yourself maintenance
1Remove the tire valve cap.
2
Press the tip of the tire pressure 
gauge onto the tire valve.
3
Read the pressure using the gauge 
gradations.
4
If the tire inflation pressure is not at 
the recommended level, adjust the 
pressure.
If you add too much air, press the 
center of the valve to deflate.
5
After completing the tire inflation 
pressure measurem ent and adjust-
ment, apply soapy water to the 
valve and check for leakage.
6
Put the tire valve cap back on.
■Tire inflation pressure check interval
You should check tire  inflation pressure 
every two weeks, or at least once a month. 
Do not forget to check the spare.
■Effects of incorrect tire inflation pres-
sure
Driving with incorrect ti re inflation pressure 
may result in the following:
●Reduced fuel economy
●Reduced driving comfort and poor han-
dling
●Reduced tire life due to wear
●Reduced safety
●Damage to the drivetrain
If a tire needs frequent inflating, have it 
checked by your Lexus dealer.
■Instructions for checking tire inflation 
pressure
When checking tire inflation pressure, 
observe the following:
●Check only when the tires are cold.
If your vehicle has been parked for at 
least 3 hours or has not been driven for 
more than 1 mile or 1.5 km, you will get an 
accurate cold tire in flation pressure read- ing.
●Always use a tire pressure gauge.
It is difficult to judge if a tire is properly 
inflated based only on its appearance.
●It is normal for the ti
re inflation pressure 
to be higher after driving as heat is gen-
erated in the tire. Do not reduce tire infla-
tion pressure after driving.
●Never exceed the vehicle capacity 
weight.
Passengers and luggage weight should 
be placed so that the vehicle is balanced.
WARNING
■Proper inflation is critical to save tire 
performance
Keep your tires properly inflated. 
If the tires are not properly inflated, the 
following conditions may occur which 
could lead to an accident resulting in 
death or serious injury:
●Excessive wear
●Uneven wear
●Poor handling
●Possibility of blowouts resulting from 
overheated tires
●Air leaking from between tire and 
wheel
●Wheel deformation and/or tire dam-
age
●Greater possibility  of tire damage 
while driving (due to road hazards, 
expansion joints, sharp edges on the 
road, etc.)
NOTICE
■When inspecting and adjusting tire 
inflation pressure
Be sure to put the tire valve caps back on.
If a valve cap is not installed, dirt or mois-
ture may get into the valve and cause an 
air leak, resulting in decreased tire infla-
tion pressure. 

2907-2. Steps to take in an emergency
■When the tire pressure warning light 
comes on
Check the tire inflation pressure and adjust 
to the appropriate level. Pushing the tire 
pressure warning reset switch will not turn 
off the tire pressure warning light.
■The tire pressure warning light may 
come on due to natural causes
The tire pressure warning light may come 
on due to natural causes such as natural air 
leaks and tire inflation pressure changes 
caused by temperature.  In this case, adjust-
ing the tire inflation pressure will turn off the 
warning light (after  a few minutes).
■When a tire is replaced with the spare 
tire
The spare tire is not equipped with a tire 
pressure warning valve  and transmitter. If a 
tire goes flat, the tire  pressure warning light 
will not turn off even though the flat tire has 
been replaced with the spare tire.
■Conditions that the  tire pressure warn-
ing system may not function properly
 P.260
■If the tire pressure warning light fre-
quently comes on after blinking for 1 
minute
If the tire pressure wa rning light frequently 
comes on after blinking for 1 minute when 
the engine switch is turned to IGNITION 
ON mode, have it checked by your Lexus 
dealer.
■Warning buzzer
In some cases, the buzzer may not be heard 
due to being in a noisy location or audio 
sound.
WARNING
■If both the ABS and the brake system 
warning lights remain on
Stop your vehicle in a safe place immedi-
ately and contact your Lexus dealer. The 
vehicle will become extremely unstable 
during braking, and the ABS system may 
fail, which could cause an accident 
resulting in death or serious injury.
■When the electric power steering 
system warning light comes on
The steering wheel may become 
extremely heavy.
When steering wheel operations are 
heavier than usual, grip the steering 
wheel firmly and operate it using more 
force than usual.
■If the tire pressure warning light 
comes on
Be sure to observe the following precau-
tions. Failure to do so could cause a loss 
of vehicle control and result in death or 
serious injury.
●Stop your vehicle in a safe place as 
soon as possible. Adjust the tire infla-
tion pressure immediately.
●If the tire pressure warning light comes 
on even after tire inflation pressure 
adjustment, it is prob able that you have 
a flat tire. Check the tire s. If a tire is flat, 
change it with the spare tire and have 
the flat tire repaired by the nearest 
Lexus dealer.
●Avoid abrupt maneuvering and brak-
ing. If the vehicle tires deteriorate, you 
could lose control of the steering 
wheel or the brakes.
■If a blowout or sudden air leakage 
should occur
The tire pressure warning system may 
not activate immediately. 

2917-2. Steps to take in an emergency
7
When trouble arises
WARNING
■Maintenance of the tires
Each tire, including the spare (if pro-
vided), should be checked monthly when 
cold and inflated to the inflation pressure 
recommended by the vehicle manufac-
turer on the vehicle placard or tire infla-
tion pressure label (tire and load 
information label). (If your vehicle has 
tires of a different size than the size indi-
cated on the vehicle placard or tire infla-
tion pressure label [tire and load 
information label], yo u should determine 
the proper tire infl ation pressure for 
those tires.)
As an added safety feature, your vehicle 
has been equipped with a tire pressure 
monitoring system (TPMS-tire pressure 
warning system) that illuminates a low 
tire pressure telltale  (tire pressure warn-
ing light) when one or more of your tires 
is significantly under-inflated. Accord-
ingly, when the low tire pressure telltale 
(tire pressure warnin g light) illuminates, 
you should stop and check your tires as 
soon as possible, and inflate them to the 
proper pressure. Driving on a signifi-
cantly under-inflated tire causes the tire 
to overheat and can lead to tire failure. 
Under-inflation also reduces fuel effi-
ciency and tire tread life, and may affect 
the vehicle’s handling and stopping abil-
ity.
Please note that the TPMS (tire pressure 
warning system) is not a substitute for 
proper tire maintenance, and it is the 
driver’s responsibility  to maintain correct 
tire pressure, even if under-inflation has 
not reached the level to trigger illumina-
tion of the TPMS low tire pressure telltale 
(tire pressure warning light).
Your vehicle has also been equipped with 
a TPMS (tire pressure warning system) 
malfunction indicator  to indicate when 
the system is not operating properly. The 
TPMS (tire pressure warning system) 
malfunction indicator is combined with 
the low tire pressure telltale (tire pres-
sure warning light) . When the system 
detects a malfunction, the telltale will 
flash for approximately one minute and 
then remain continuously illuminated. 
This sequence will continue upon subse-
quent vehicle start-ups as long as the 
malfunction exists. When the malfunction 
indicator is illuminated, the system may 
not be able to detect or signal low tire 
pressure as intended.
TPMS (tire pressure warning system) 
malfunctions may occur for a variety of 
reasons, including the installation of 
replacement or alternate tires or wheels 
on the vehicle that prevent the TPMS 
(tire pressure warning system) from func-
tioning properly. Always check the 
TPMS (tire pressure warning system) 
malfunction telltale after replacing one 
or more tires or wheels on your vehicle to 
ensure that the replacement or alternate 
tires and wheels allow the TPMS (tire 
pressure warning system) to continue to 
function properly.
NOTICE
■To ensure the tire pressure warning 
system operates properly
Do not install tires with different specifi-
cations or makers, as the tire pressure 
warning system may not operate prop-
erly.