2020 Lexus LC500h high beam

3TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9
4-1. Before drivingDriving the vehicle ........................ 138
Cargo and luggage ...................... 144
Vehicle load limits ......................... 146
Trailer towing .................................. 147
Dinghy towing ................................ 147
4-2. Driving procedures Engine (ignition) switch (LC500)............................................................ 148
Power (ignition) switch (LC500h) ............................................................. 151
EV drive mode (LC500h)........ 155
Automatic transmission (LC500) ............................................................ 157
Hybrid transmission (LC500h) ............................................................ 163
Turn signal lever............................. 169
Parking brake ................................. 170
Brake Hold....................................... 173
4-3. Operating the lights and wipers Headlight switch ............................ 175
Automatic High Beam ................ 178
Windshield wipers and washer 180
4-4. Refueling Opening the fuel tank cap......... 184
4-5. Using the driving support systems Lexus Safety System + ................ 187
PCS (Pre-Collision System)..... 192
LKA (Lane-Keeping Assist) ..... 199
Dynamic radar crui se control with
full-speed range......................... 206
Driving mode select switch....... 216
Intuitive parking assist ................. 217BSM (Blind Spot Monitor) ........223
Active rear wing ............................
232
Driving assist systems ................ 235
4-6. Driving tips Hybrid vehicle driving tips (LC500h).................................... 240
Winter driving tips ........................ 242
5-1. Remote Touch Remote Touch............................... 246
5-2. Lexus Climate Concierge Lexus Climate Concierge........ 250
5-3. Using the air conditioning system Automatic air conditioning system........................................................... 252
Heated steering wheel/seat heat- ers/seat ventilators................... 259
5-4. Using the interior lights Interior lights list ............................ 262
5-5. Using the storage features List of storage features .............. 264
Trunk features ............................... 266
5-6. Using the other interior features Other interior features .............. 268
Garage door opener ................. 270
6-1. Maintenance and care Cleaning and protecting the vehi-cle exterior................................... 278
Cleaning and protecting the vehi- cle interior ..................................... 281
4Driving
5Interior features
6Maintenance and care

762-1. Instrument cluster
after a few seconds. There may be a
malfunction in a system if a light does
not come on, or turn off. Have the vehi-
cle inspected by your Lexus dealer.
*2: This light illuminates on the multi-infor-mation display.
*3: The light flashes to indicate a malfunc-tion.
*4: This light illuminates on the center panel.
The indicators inform the driver of the
operating state of the vehicle’s various
systems.
■Operation indicators
WARNING
■If a safety system warning light does
not come on
Should a safety system light such as the
ABS and SRS warning light not come on
when you start the engine tem>, this could mean that these systems
are not available to he lp protect you in an
accident, which could result in death or
serious injury. Have the vehicle inspected
by your Lexus dealer immediately if this
occurs.
Indicators
Turn signal indicator
(  P.169)
(U.S.A.)
Headlight indicator ( P.175)
(Canada)
Tail light indicator ( P.175)
Headlight high beam indica-
tor ( P.177)
Automatic High Beam indica-
tor
*1 (  P.178)
Cruise control indicator*2
(  P.206)
Dynamic radar cruise control
indicator
*2 (  P.206)
Cruise control “SET” indica-
tor
*2 (  P.206)
(white)
LKA indicator*2 ( P.199)
(green)
LKA indicator*2 ( P.199)
(orange)
LKA indicator*2, 3 ( P.199)
(if equipped)
Intuitive parking assist indica-
tor ( P.217)
Slip indicator
*1, 3 (  P.236)
VSC OFF indicator
*1
(  P.236)
PCS warning light
*1, 4
(  P.194)
BSM (Blind Spot Monitor)
outside rear view mirror indi-
cators
*5, 6 (  P.223)
BSM (Blind Spot Monitor)
indicator ( P.223)
RCTA (Rear Cross Traffic
Alert) indicator ( P.223)
Brake hold standby indica-
tor
*1 (  P.173)
Brake hold operated indica-
tor
*1 (  P.173)
Security indicator
*7 (  P.68,
70)
Smart access system with
push-button start indicator
*2
(  P.148, 151)

137
4
4
Driving
Driving
4-1. Before drivingDriving the vehicle ..................... 138
Cargo and luggage ................... 144
Vehicle load limits ...................... 146
Trailer towing ............................... 147
Dinghy towing ............................. 147
4-2. Driving procedures Engine (ignition) switch (LC500)......................................................... 148
Power (ignition) switch (LC500h) .......................................................... 151
EV drive mode (LC500h)..... 155
Automatic transmission (LC500) ......................................................... 157
Hybrid transmission (LC500h) ......................................................... 163
Turn signal lever.......................... 169
Parking brake .............................. 170
Brake Hold.................................... 173
4-3. Operating the lights and wipers Headlight switch ......................... 175
Automatic High Beam ............. 178
Windshield wipers and washer ......................................................... 180
4-4. Refueling Opening the fuel tank cap...... 184
4-5. Using the driving support sys- tems
Lexus Safety System + ............. 187
PCS (Pre-Collision System).. 192
LKA (Lane-Keeping Assist) .. 199Dynamic radar cruise control with
full-speed range...................... 206
Driving mode select switch ... 216
Intuitive parking assist ............... 217
BSM (Blind Spot Monitor) .... 223
Active rear wing ........................ 232
Driving assist systems.............. 235
4-6. Driving tips Hybrid vehicle driving tips (LC500h)................................. 240
Winter driving tips ..................... 242

1774-3. Operating the lights and wipers
4
Driving
1With the headlights on, push the
lever away from you to turn on the
high beams.
Pull the lever toward you to the center
position to turn the high beams off.
2Pull the lever toward you and
release it to flash the high beams
once.
You can flash the high beams with the
headlights on or off.
When any of the following conditions is
met, while the headlights (low beam)
are on, the cornering lights will addi-
tionally turn on and light up the direc-
tion of movement for the vehicle. This is
to ensure excellent visibility when
either driving at intersections or park-
ing at night.
The steering wheel is operated
 The turn signal lever is operated
 The shift position is in R (both left
and right side cornering lights)
■Cornering light control
●The lights illuminate when the vehicle speed is approximately 19 mph (30
km/h) or less. However,
the lights turn off
when the vehicle speed increases to
approximately 22 mph (35 km/h) or
more.
●After the lights remain illuminated for 30
minutes, they automatically turn off.
Turning on the high beam head-
lights
Cornering lights

1784-3. Operating the lights and wipers
1Push the lever away from you with
the headlight switch in the or
position.
2 Press the Automatic High Beam
switch.
The Automatic High Beam indicator will
come on when the headlights are turned on automatically to indicate that the system
is active.
■High beam automatic turning on or off
conditions
●When all of the follo
wing conditions are
met, the high beam will be automatically
turned on (after approximately 1 second):
• Vehicle speed is above approximately 21 mph (34 km/h).
• The area ahead of the vehicle is dark.
• There are no vehicles ahead with head- lights or tail lights turned on.
• There are few streetlights on the road ahead.
●If any of the following conditions are met,
the high beam will be automatically
turned off:
• Vehicle speed drops below approxi- mately 17 mph (27 km/h).
• The area ahead of the vehicle is not dark.
• Vehicles ahead have headlights or tail
lights turned on.
• There are many streetlights on the road
ahead.
■Camera sensor dete ction information
●The high beam may not be automatically
turned off in the following situations:
• When oncoming vehicles suddenly appear from a curve
• When the vehicle is cut in front of by another vehicle
• When vehicles ahead are hidden from sight due to repeated curves, road divid-
ers or roadside trees
• When vehicles ahead appear from the faraway lane on wide road
• When vehicles ahead have no lights
●The high beam may be turned off if a
vehicle ahead that is using fog lights with-
Automatic High Beam
The Automatic High Beam uses an
in-vehicle camera sensor to assess
the brightness of streetlights, the
lights of vehicle ahead, etc., and
automatically turn s the high beam
on or off as necessary.
WARNING
■Limitations of the Automatic High
Beam
Do not rely on the Automatic High
Beam. Always drive sa fely, taking care to
observe your surroundings and turning
the high beam on or off manually if nec-
essary.
■To prevent incorrect operation of the
Automatic High Beam system
Do not overload the vehicle.
Activating the Automatic High
Beam system

1794-3. Operating the lights and wipers
4
Driving
out using the headlights is detected.
●House lights, street lights, traffic signals,
and illuminated billboards or signs may
cause the high beam to switch to the low
beams, or the low beams to remain on.
●The following factors may affect the
amount of time taken to turn the high
beam on or off:
• The brightness of headlights, fog lights, and tail lights of vehicles ahead
• The movement and direction of vehicles ahead
• When a vehicle ahead only has opera-
tional lights on one side
• When a vehicle ahead is a two-wheeled vehicle
• The condition of the road (gradient, curve, condition of the road surface etc.)
• The number of passengers and amount of
luggage
●The high beam may be turned on or off
when the driver does not expect it.
●Bicycles or similar objects may not be
detected.
●In the situations show n below, the system
may not be able to accurately detect sur-
rounding brightness levels. This may
cause the low beams to remain on or the
high beams to cause problems for pedes-
trians, vehicles ahead or other parties. In
these cases, manually switch between the
high and low beams.
• In bad weather (rain, snow, fog, sand- storms etc.)
• The windshield is obscured by fog, mist, ice, dirt etc.
• The windshield is cracked or damaged.
• The camera sensor is deformed or dirty.
• Surrounding brightness levels are equal to those of headlights, tail lights or fog
lights.
• Vehicles ahead have headlights or tail lights that are either switched off, dirty,
changing color, or have improperly
adjusted aim.
• When driving through an area of inter- mittently changing brightness and dark-
ness.
• When frequently and repeatedly driving ascending/descending roads, or roads
with rough, bumpy or uneven surfaces
(such as stone-paved roads, gravel tracks etc.).
• When frequently and repeatedly taking curves or driving on a winding road.
• There is a highly re flective object ahead
of the vehicle, such as a sign or a mirror.
• The vehicle’s headlights are damaged or
dirty.
• The vehicle is listing or titling, due to a flat tire, a trailer being towed etc.
• The driver believes that the high beam may be causing problems or distress to
other drivers or pedestrians nearby.
■Temporarily lowering sensor sensitivity
The sensitivity of the sensor can be tempo-
rarily lowered.
1 Turn the engine switch
off while the following conditions are
met.
• The headlight swit ch is in or .
• The headlight switch lever is in high beam position.
• Automatic High Be am switch is on.
2 Turn the engine switch
to IGNITION ON mode .
3 Within 30 seconds after 2, repeat pull-
ing the headlight switch lever to the
original position then pushing it to the
high beam position quickly 10 times,
then leave the lever in high beam posi-
tion.
4 If the sensitivity is changed, the Auto-
matic High Beam indicator turns on and
off 3 times.
Automatic High Beam (headlights) may
turn on even the vehicle is stopped.
■Switching to low beam
Pull the lever to the original position.
The Automatic High Beam indicator will
turn off.
Push the lever away from you to activate
the Automatic High Beam system again.
Turning the high beam on/off
manually

1804-3. Operating the lights and wipers
■Switching to high beam
Press the Automatic High Beam
switch.
The Automatic High Beam indicator will
turn off and the high beam indicator will
turn on.
Press the switch to activate the Automatic
High Beam system again.
Operating the lever operates
the wipers or washer as follows. When
“AUTO” is selected, the wipers will
operate automatically when the sen-
sor detects falling rain. The system
automatically adjusts wiper timing in
accordance with rain volume and vehi-
cle speed.
Windshield wipers and
washer
Operating the lever can switch
between automatic operation and
manual operation, or can use the
washer.
NOTICE
■When the windshield is dry
Do not use the wipers, as they may dam-
age the windshield.
Operating the wiper lever

1874-5. Using the driving support systems
4
Driving
4-5.Using the driving support systems
■PCS (Pre-Collision System)
 P.192
■LKA (Lane-Keeping Assist)
 P.199
■Automatic High Beam
 P.178
■Dynamic radar cruise control with
full-speed range
 P.206
The pre-collision system is equipped
with a sophisticated computer that will record certain data, such as:
• Accelerator status
•Brake status
• Vehicle speed
• Operation status of the pre-collision
system functions
• Information (such as the distance and relative speed between your
vehicle and the vehicle ahead or
other objects)
• Images from the camera sensor (available only when the pre-colli-
sion braking function or the pre-col-
lision brake assist function was
operating)
The pre-collision system does not
record conversations, sounds or
images of the inside of the vehicle.
 Data usage
Lexus may use the data recorded in this
computer to diagnose malfunctions, con-
duct research and development, and
improve quality.
Lexus will not disclose the recorded data to
a third party except:
• With the consent of the vehicle owner or
with the consent of the lessee if the vehi-
cle is leased
• In response to an official request by the police, a court of law or a government
agency
• For use by Lexus in a lawsuit
• For research purposes where the data is not tied to a specific vehicle or vehicle
owner
 Recorded images can be erased
using a specialized device.
The image recording function can be dis-
abled. However, if the function is disabled,
Lexus Safety System +
The Lexus Safety Sy stem + consists
of the following drive assist systems
and contributes to a safe and com-
fortable driving experience:
Drive assist systems of Lexus
Safety System +
WARNING
■Lexus Safety System +
The Lexus Safety System + is designed to
operate under the assumption that the
driver will drive safely, and is designed to
help reduce the impact to the occupants
and the vehicle in the case of a collision
or assist the driver in normal driving con-
ditions.
As there is a limit to the degree of recog-
nition accuracy and control performance
that this system can provide, do not
overly rely on this system. The driver is
always responsible for paying attention
to the vehicle’s surro undings and driving
safely.
Vehicle data recording