2020 KIA SORENTO buttons

35ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER
Front Seat Headrest Adjustment†1 0
Type A*
•To raise the headrest, pull headrest up to the desired position
•To lower the headrest, press the button, then press the headrest down
Type B/C*
•To raise the headrest, pull the headrest up to the desired position
•To lower the headrest, press and hold the release button A and lower
the headrest to the desired position
Driver Position Memory System*†1 8
The integrated system stores into memory the position of the Driver’s
Seat and the Outside Rearview Mirrors.
To store positions into memory, first place the Gear Shift into P (Park)
while the Engine Start /Stop button is in the ON position. Then:
1. Adjust the Driver’s Seat and the Outside Mirrors
2. Press the SET button B on the control panel. System will beep once
3. Press one of the memory buttons C within 5 seconds. The system
will beep twice when memory has been stored
SET
1
2
(Buttons located on Driver's Door Panel) ( Type A )( Type B)
B
C
REMINDER: Do not attempt to operate the driver position memory system while the vehicle is moving. This could result in loss of control of the vehicle.
For easy adjustments, hold a headrest post with one hand while using the other hand to pull the headrest from underneath.
QUICK TIP
REMINDERS:
•
The headrest only moves up and down as described above. It does not adjust forward or backward
•
Do not operate the vehicle with the headrests removed. Headrests can provide critical neck and head support in an accident
AA
SEATING

SORENTO FEATURES & FUNCTIONS GUIDE
SEATING
*IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER38
3rd-Row Folding Seat*†1 8
One-Touch Walk-In Seat Access
Folding 3rd-Row Seat
1. Fully lower the headrest A
2. Pull the Seat folding strap B located on the Seatback
3. Fold the Seat down
Walk-In Seat Lever*
To enter the 3rd-Row Seat* area, do the following steps:
1. Place the Seatbelt into the guide clip and tighten the
Seatbelt by pulling up
2. Pull lever C located on the 2nd-Row Seatback
3. Fold the Seatback forward and slide to the farthest
forward position
4. Return Seatback to its original position and ensure it
locks (clicks) into place
To get in and out of the 3rd Row Seat, adjust the 2nd Row Seat by
pressing the top or bottom One-Touch Walk-In Seat Access buttons D
(located on left side of the front passenger’s seatback):
1. Set the front seatback to the most upright position, and slide the seat
forward, if needed
2. Lower the 2nd Row Seat Headrest to the lowest position
3. Insert the seatbelt buckle into the pocket between the rear seatback
and the cushion
4. Press the One-Touch Walk-In Seat Access buttons to slide the Seat
forward
B
AA
For more information on 3rd-Row Seat operation, refer to the Owner's Manual.
2nd & 3rd Row Folding Seats Video To view a video on your mobile device, snap this QR Code or visit the listed website.
Refer to page 2 for more information.
QR CODE
www.youtube.com/KiaFeatureVideosFor more information on 2nd-Row Walk-In Seat operation, refer to the Owner's Manual.
(Lever located on 2nd-Row Seatback)
C
D
The strap can be used in the back of the 2nd Row Seat to slide and fold the 2nd Row Seats.
QUICK TIP
REMINDER: Do not use the One-Touch Walk-In Seat Access buttons while the front passenger seat is occupied.

SORENTO FEATURES & FUNCTIONS GUIDE44*IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER
Erasing programmed buttons:
How to Sync Transmitter with HomeLink®*
If programming for the first time, begin with Step 1
(repeating this step will delete all information).
To program non-rolling and rolling code garage
door openers and other devices:
1. Press and hold the left A and center D buttons
simultaneously until the indicator light C begins
to flash (to reprogram buttons, skip this step)
2. Press and hold the desired button A B D
and hold the button on the transmitter while it
is approximately 1 to 3 inches away from the
mirror. The HomeLink® Indicator light C will
flash rapidly once the frequency signal has been
successfully programmed
To finish programming rolling code garage door
openers, complete these steps:
3. Locate the “learn” or “smart” button on the garage door’s motor head unit.
Press and release the button and complete Step 4 within 30 seconds
4. Firmly press and release the programmed HomeLink® button up to three times
Press and hold the left A and center D buttons simultaneously for
approximately 20 seconds, and then release both buttons within 30 seconds.
Operating HomeLink®:
Press one of the programmed HomeLink® buttons.
REMINDER: The mirror indicator light C will illuminate when automatic dimming is ON.
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink Repeater Kit. For more information, go to www.HomeLink.com or call (800) 355-3515.
The HomeLink® / Auto-Dimming Rearview Mirror* is designed to
reduce glare from a vehicle’s headlights located in the rear and
also connect up to three electronic transmitters into one location.
•
To turn automatic dimming ON, press – button F
•
To turn automatic dimming OFF, press – button G
HomeLink®†12 with Auto-Dimming Rearview Mirror*
A HomeLink® button
B HomeLink® button
C Indicator light
D HomeLink® button
E Glare detection sensor
F Automatic dimming ON
G Automatic dimming OFF
ABCDEFG
•
•You can reprogram a single HomeLink® button by repeating Step 2 •Erasing the programmed buttons will delete all trained transmitters
QUICK TIPS
Homelink® Setup Video To view a video on your mobile device, snap this QR Code or visit the listed website.
Refer to page 2 for more information.
www.youtube.com/KiaFeatureVideos
QR CODE
OTHER KEY FEATURES