2020 INFINITI QX80 tire pressure

33
RETREADED TIRES
Retreaded passenger and light truck tires
are not warranted by Goodyear and Dunlop
for any reason. Goodyear and Dunlop speed
ratings and U.S. Department of Transportation
test compliance certifications are voided for
retreaded tires.
DO MAINTAIN VEHICLE
SUSPENSION, WHEEL ALIGNMENT
AND BALANCE AND ROTATE YOUR
TIRES
Lack of rotation, worn suspension parts,
underinflation/overinflation, wheel imbalance
and misalignment can cause vibration
or irregular tire wear. Rotate your tires
according to your vehicle manufacturer’s
recommendations or at maximum intervals of
6,000 miles/10,000 km.
FOR ADDITIONAL INFORMATION, SEE
THE “BE TIRE SMART/PLAY YOUR PART
BROCHURE” PUBLISHED BY THE RUBBER
MANUFACTURERS ASSOCIATION (RMA).
A COPY OF THIS BROCHURE CAN BE
DOWNLOADED FROM THE RMA WEBSITE:
www.rma.org/publications/consumer_tire_
information
You must go to an authorized Goodyear or
Dunlop outlet for replacement tires and all
warranty service.
TIRE SERVICE LIFE
Tires are designed and built to provide many
thousands of miles of excellent service. For
maximum benefit, tires must be maintained
properly to avoid tire damage that may result
in removal from service before the tread is
worn down to minimum depth.
It is not practical to accurately predict the
service life of any specific tire in chronological
time since service conditions vary widely. The
serviceability of a tire over time is a function
of the storage and service conditions (inflation
pressure, load, speed, road hazard injury, etc.)
to which a tire is subjected. Consumers should
not rely solely on the appearance of the tire,
but should be aware of any change in dynamic
performance such as increased air loss, noise
or vibration, which could be a sign to remove
the tire. Therefore, it is essential to have tires,
including spares, inspected regularly (at least
monthly) for proper inflation pressure, damage
and treadwear.
FOR SERVICE ASSISTANCE OR
INFORMATION, FIRST CONTACT THE
NEAREST GOODYEAR OR DUNLOP
RETAILER.
1) For assistance in locating the nearest
Goodyear or Dunlop Retailer, look in the
Yellow Pages under Tire Dealers – New.
2) Go to www.goodyear.com for U.S. or
www. goodyear.ca for Canada.
For Dunlop tires, go to
www.dunloptires.com for U.S. & Canada. If additional assistance is required, call the
Customer Assistance Center
at 1-800-321-2136 for U.S. or
1-800-387-3288 for Canada.
Or write to:
Customer Assistance Center
Dept 728
1144 East Market Street
Akron, OH 44316-0001
Check your vehicle’s Owner’s Manual (or your
vehicle) to determine if it is equipped with run-
flat (extended mobility) tires. If your vehicle
is equipped with run-flat tires, the following
applies:
RUN-FLAT TECHNOLOGY EXTENDED
MOBILITY TECHNOLOGY (EMT™),
RUNONFLAT
® (ROF) AND DUNLOP SELF-
SUPPORTING TECHNOLOGY (DSST®)
ORIGINAL EQUIPMENT TIRES
IMPORTANT SAFETY
INFORMATION
OPERATIONAL MONITORING
The information contained in this Limited
Warranty Brochure applies only to the Original
Equipment tires supplied with your vehicle.
In order for Goodyear Run-Flat (Extended
Mobility Technology [EMT], RunOnFlat [ROF])
or Dunlop Run-Flat (Dunlop Self-Supporting
Technology [DSST]) tires to obtain the
performance criteria stated within this Limited
Warranty, Goodyear or Dunlop Run-Flat tires
GOODYEAR/DUNLOP TIRE LIMITED WARRANTY
(Continued on next page)

34
must use specific parts, such as a low tire
pressure monitoring system authorized by the
Original Equipment vehicle manufacturer.
RUN-FLAT TIRE FEATURE:
The Goodyear or Dunlop Run-Flat tire is a high
performance tire with a remarkable feature:
It can operate for limited distances with very
low or even no inflation pressure (refer to your
Vehicle Owner’s Manual for these limitations).
This is an important benefit, especially if
inflation loss occurs at a location where
immediately stopping your vehicle could be
hazardous.
TIRE PRESSURE MONITORING SYSTEM
ALERT
Refer to your vehicle Owner’s Manual for more
information on what to do if the tire pressure
warning system activates.
WARNING
If the tire pressure-monitoring system signals
an alert, follow these safety precautions to
prevent a loss of vehicle control that could
result in serious personal injury or death:
•• Slow your speed. Do not exceed 50 mph
(80 kph).
•• Avoid hard cornering, hard braking and
severe handling maneuvers.
•• Avoid potholes and other road hazards.
Remember that when your tires have lost air
pressure, your vehicle’s handling capability is
reduced, particularly during severe maneuvers.TO PROLONG TIRE LIFE DURING A SYSTEM
ALERT
The Goodyear or Dunlop Run-Flat tire can be
driven at low or zero air pressure (refer to your
vehicle Owner’s Manual for these limitations).
To help prolong the life of a tire operating
under low-inflation conditions, drive at a speed
as far below 50 mph (80 kph) as possible. Also,
drive the shortest distance possible before
obtaining tire service. Taking these precautions
will increase the chance that your tire will be
repairable.
SERVICE AFTER A SYSTEM ALERT
To obtain service after operating under low-
inflation conditions, contact your Goodyear or
Dunlop Run-Flat service facility. Trained service
personnel will inspect your tires to determine
if they are in need of repair or replacement.
To locate the nearest authorized Goodyear or
Dunlop Run-Flat service facility, call 1-800-
GOODYEAR (1-800-466-3932).
WARNING
Because of the unique characteristics of
Run-Flat tires, the wheels on which they
are mounted and your vehicle’s tire pressure
monitoring system, all tire service work other
than routine inflation maintenance and
external inspections must be performed by
service personnel at a Goodyear or Dunlop
Run-Flat service facility. Do not attempt to
mount or demount Run-Flat tires yourself;
serious injury or death could result. Only
specially trained persons should mount,
demount and repair Run-Flat tires, and more than 40 psi (270 kPa) may be required to seat
beads. A safety cage and clip-on extension
air hose must be used if more than 40 psi
(270kPa) is need to seat beads.
TIRE REPAIR
Like any other Goodyear or Dunlop speed-
rated, high performance tire, the Goodyear
or Dunlop Run-Flat tire may be repaired to
correct a puncture in the tread, but PROPER
MATERIALS AND PROCEDURES MUST BE
USED. Contact a Goodyear or Dunlop Run-
Flat service facility for information on proper
repairs. For the location of the nearest facility,
call 1-800-GOODYEAR (1-800-466- 3932).
WARNING
Goodyear and Dunlop Run-Flat tires are
designed for use only on certain original
equipment wheels supplied with a properly
operating low tire pressure-monitoring system.
If applied to a vehicle without a properly
operating low tire pressure-monitoring
system, the tires may fail when operated in
an underinflated condition, resulting in loss of
vehicle control and possible serious injury or
death. Application of these tires to a vehicle
not equipped with specified operational low
tire pressure monitoring system constitutes
improper and unsafe use of this product.OPERATIONAL MONITORING The information contained in this Limited
Warranty Brochure applies only to the Original
Equipment tires supplied with your vehicle.
GOODYEAR/DUNLOP TIRE LIMITED WARRANTY
(Continued on next page)

35
In order for Goodyear Run-Flat (Extended
Mobility Technology [EMT], RunOnFlat [ROF])
or Dunlop Run-Flat (Dunlop Self- Supporting
Technology [DSST]) tires to obtain the
performance criteria stated within this Limited
Warranty, Goodyear or Dunlop Run- Flat tires
must use specific parts, such as a low tire
pressure monitoring system authorized by the
Original Equipment vehicle manufacturer.
RUN-FLAT TIRE FEATURE:The Goodyear or Dunlop Run-Flat tire is a high
performance tire with a remarkable feature:
It can operate for limited distances with very
low or even no inflation pressure (refer to your
Vehicle Owner’s Manual for these limitations).
This is an important benefit, especially if
inflation loss occurs at a location where
immediately stopping your vehicle could be
hazardous.
TIRE PRESSURE MONITORING
SYSTEM ALERT
Refer to your vehicle Owner’s Manual for more
information on what to do if the tire pressure
warning system activates.
WARNING
If the tire pressure-monitoring system signals
an alert, follow these safety precautions to
prevent a loss of vehicle control that could
result in serious personal injury or death:
•• Slow your speed. Do not exceed 50 mph
(80 kph).
•• Avoid hard cornering, hard braking and
severe handling maneuvers.
•• Avoid potholes and other road hazards.
Remember that when your tires have lost air
pressure, your vehicle’s handling capability is
reduced, particularly during severe maneuvers.
TO PROLONG TIRE LIFE DURING A
SYSTEM ALERT
The Goodyear or Dunlop Run-Flat tire can be
driven at low or zero air pressure (refer to your
vehicle Owner’s Manual for these limitations).
To help prolong the life of a tire operating
under low-inflation conditions, drive at a speed
as far below 50 mph (80 kph) as possible. Also,
drive the shortest distance possible before
obtaining tire service. Taking these precautions
will increase the chance that your tire will be
repairable.
SERVICE AFTER A SYSTEM ALERT To obtain service after operating under low-
inflation conditions, contact your Goodyear or
Dunlop Run-Flat service facility. Trained service
personnel will inspect your tires to determine
if they are in need of repair or replacement.
To locate the nearest authorized Goodyear or
Dunlop Run-Flat service facility, call 1-800-
GOODYEAR (1-800-466-3932).
WARNING
Because of the unique characteristics of
Run-Flat tires, the wheels on which they
are mounted and your vehicle’s tire pressure
monitoring system, all tire service work other
than routine inflation maintenance and
external inspections must be performed by
service personnel at a Goodyear or Dunlop Run-Flat service facility. Do not attempt to
mount or demount Run-Flat tires yourself;
serious injury or death could result. Only
specially trained persons should mount,
demount and repair Run-Flat tires, and more
than 40 psi (270 kPa) may be required to seat
beads. A safety cage and clip-on extension
air hose must be used if more than 40 psi
(270kPa) is needed to seat beads.
TIRE REPAIR Like any other Goodyear or Dunlop speed-
rated, high performance tire, the Goodyear
or Dunlop Run-Flat tire may be repaired to
correct a puncture in the tread, but PROPER
MATERIALS AND PROCEDURES MUST BE
USED. Contact a Goodyear or Dunlop Run-
Flat service facility for information on proper
repairs. For the location of the nearest facility,
call 1-800-GOODYEAR (1-800-466-3932).
WARNING
Goodyear and Dunlop Run-Flat tires are
designed for use only on certain original
equipment wheels supplied with a properly
operating low tire pressure-monitoring system.
If applied to a vehicle without a properly
operating low tire pressure-monitoring
system, the tires may fail when operated in
an underinflated condition, resulting in loss of
vehicle control and possible serious injury or
death. Application of these tires to a vehicle
not equipped with specified operational low
tire pressure monitoring system constitutes
improper and unsafe use of this product.
GOODYEAR/DUNLOP TIRE LIMITED WARRANTY

40
TO THE EXTENT PERMITTED BY LAW,
COMPANY DISCLAIMS LIABILITY FOR
ALL CONSEQUENTIAL AND INCIDENTAL
DAMAGES. THE REMEDIES SET FORTH IN
THIS LIMITED WARRANTY ARE THE SOLE
AND EXCLUSIVE REMEDIES FOR BREACH
OF WARRANTY. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE LIMITATIONS
OR EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH MAY VARY FROM
STATE TO STATE.
5. COMPANY’S OBLIGATIONS
Any replacement qualifying under this
Adjustment Policy will be made by any
Continental or General brand authorized
retailer or vehicle retailer authorized to handle
Continental or General brand tire adjustments.
Company will replace the tire pursuant to the
terms of this Adjustment Policy.
6. OWNER’S OBLIGATIONS
To make a claim under this Policy concerning
any tire which is covered by this Policy, you
must present your claim with the tire to any
Continental or General brand tire retailer
or vehicle retailer authorized to handle
Continental/General brand tires. For the
nearest Continental or General brand tire
retailer, check the Yellow Pages, or use the
Continental or General brand Internet address, or one of the “800” numbers shown under
“For Client Assistance.” To be eligible for the
terms of this Policy, you need to present your
new vehicle registration form or new vehicle
sales invoice showing date of purchase. Tires
replaced on an adjustment basis become the
property of Company. You will be required to
sign the Company Limited Warranty Claim
Form or retailer replacement sales receipt.
You are responsible for payment of all
applicable taxes demounting, mounting and
balancing charges set forth under this Policy.
You are also responsible for payment of local
tire-disposal fees and any parts or service
regardless of mileage or months of service. This
includes payment for tire rotation, alignment,
towing, road service, valve stems and tire
repairs.
Owner is responsible for maintaining proper
tire air pressure and for proper maintenance of
the tire.
THE WARRANTOR
The warrantor of Continental and General
brand tires is Continental Tire North America,
Inc., 1830 McMillan Park Drive, Fort Mill, SC
29707.
For Client Assistance:
1-800-847-3349 (Nationwide)
1-800-461-1776 (In Canada)
http://www.generaltire.com
http://www.continentaltire.com
SAFETY WARNING
Disregarding any of the safety precautions
and instructions contained in the Owner’s
Manual or the Important Tire Safety
Information in this booklet may result in tire
failure or explosion causing serious personal
injury or death.
CONTINENTAL/GENERAL TIRE LIMITED WARRANTY

41IMPORTANT TIRE SAFETY INFORMATION¹
Any tire, no matter how well constructed,may
fail due to improper maintenance or
service factors. This could create a risk of
property damage and serious or fatal injury.
Disregarding any of the safety precautions
and instructions contained in this manual may
result in tire failure or explosion causing serious
personal injury or death. For your safety,
comply with the following:
TIRE INFLATION
Keep tires inflated to the pressures
recommended on the tire data placard. (See
your Owner’s Manual for location.) These
inflation pressures must be maintained as
a minimum. However, do not exceed the
maximum pressure rating indicated on the tire
sidewall.
CHECK INFLATION PRESSURES ON ALL
YOUR TIRES, INCLUDING THE SPARE,
WHEN TIRES ARE COLD, AT LEAST ONCE A
MONTH BEFORE DRIVING.
Failure to maintain correct inflation may
result in improper vehicle handling and may
cause rapid and irregular tire wear, sudden tire
destruction, loss of vehicle control and serious
personal injury. Therefore, inflation pressures
should be checked at least once a month and
always prior to long distance trips.
Pressures should be checked when tires are
cold. The tires are cold when your vehicle has
been driven less than a mile at moderate speed
after being stopped for three or more hours.
CHECKING PRESSURE WHEN
TIRES ARE HOT
If you must add air when your tires are hot,
add four pounds per square inch (psi) (28kPa)
above the recommended cold air pressure.
Recheck the inflation pressure when the tire
is cold.
For Example Only:
Gauge reading of hot tire: 32psi
If recommended pressure is: 30psi
Desired gauge reading of hot tire 30 + 4psi =
34psi
Check cold pressures as soon as possible, at
least by the next day. Never “bleed” air from
hot tires as your tire will be underinflated. Use
an accurate tire gauge to check pressures.
Never allow children to air up tires.
DRIVING ON ANY TIRE THAT DOES
NOT HAVE THE CORRECT INFLATION
PRESSURE IS DANGEROUS. For replacement
tires, the correct inflation pressure will be
provided by your tire retailer. If not, refer to the
vehicle decal.
Underinflation produces extreme flexing of the
sidewalls and builds up heat which may result
in sudden tire destruction and serious personal
injury. Overinflating can cause the tire to be
more susceptible to impact damage.
LOAD LIMITS
DO NOT OVERLOAD. DRIVING ON ANY
OVERLOADED TIRE IS DANGEROUS. Never
load your tires beyond the load carrying limits
molded into the sidewall of the tires or the
maximum vehicle load limit as shown on the
vehicle tire data placard, whichever is less.
Overloading causes heat to build up which can
lead to sudden tire failure and serious personal
injury.
SPEED LIMITS AND SPEED RATED
TIRES
HIGH SPEED DRIVING CAN BE
DANGEROUS. Never operate your vehicle
in excess of lawful speeds or the maximum
speeds justified by the driving conditions.
Excessive speeds or racing can cause heat
buildup in a tire leading to possible failure and
serious personal injury.
Correct inflation pressure is especially
important. However, at high speeds, even with
the correct inflation pressure, a road hazard,
for example, is more difficult to avoid and if
contact is made, there is a greater chance of
causing tire damage than at the lower speed.
Moreover, driving at high speed reduces the
reaction time available to avoid accidents and
bring your vehicle to a safe stop. If you see any
damage to a tire or wheel, replace it with your
spare tire and see your tire retailer at once.
(Continued on next page)
1 Provided by and published at the request of the tire manufacturers/warrantors.

42
Tire speed ratings do not imply that a vehicle
can be safely driven at the maximum speed
for which the tire is rated. In addition, some
damages or improper repairs may cause a
speed-rated tire to lose its speed rating.
Exceeding the tire’s maximum speed rating
will cause the tire to build up excessive heat
which can cause tire damage that could result
in sudden tire destruction and rapid air loss.
Failure to control a vehicle with sudden air loss
can lead to an accident. In any case, you should
not exceed reasonable speeds as indicated by
the legal limits and driving conditions.
SPEED SYMBOLS -are shown on the sidewall
of some tires. The following table shows the
maximum speed corresponding to the symbol.SPEED RATINGS
†Speed Speed
Maximum mph km/Hr
Rating
M 81 130
N 87 140
P 93 150
R 99 160
R 106 170
S 112 180
T 118 190
H 130 210
W 168 270
Y 186 300
V* 149 240
Z** 149 240
*Some V (or VR) rated tires may have a speed
capacity of greater than 149 mph (240 km/h).
Consult your tire manufacturer for maximum
speed ratings if your vehicle capability exceeds
this speed.
**Z (or ZR) rated tires are designed for use
on cars with maximum speed capabilities
in excess of 149 mph (240 km/h).Consult
your tire manufacturer for maximum speed
capabilities.
†Although a tire may be speed rated, we do
not endorse the operation of any vehicle in
an unsafe or unlawful manner. Speed ratings are based on laboratory tests which relate
to performance on the road, but are not
applicable if tires are underinflated, overloaded,
worn out, damaged, altered, improperly
repaired, or retreaded. Furthermore, tire speed
ratings do not imply that vehicles can be safely
driven at the maximum speed for which the tire
is rated, particularly under adverse road and
weather conditions or if the vehicle has unusual
characteristics. Most highway passenger
tires that do not have a speed symbol in the
sidewall have a maximum speed rating of 105
mph. Light truck highway tires that do not
have a speed symbol on the sidewall of the tire
have a maximum speed of 87 mph. Some light
truck tires may have higher maximum speeds;
consult your tire retailer. The speed and other
ratings of retreaded tires are assigned by the
retreader and voids the original manufacturer’s
ratings.
IMPORTANT:In order to maintain the speed
capability of the vehicle, replacement tires
must have speed ratings equal to or higher
than those fitted as original equipment (as
indicated on the vehicle placard or Owner’s
Manual). If tires with lower speed ratings are
fitted, the speed capability of the vehicle will be
lowered to the maximum speed capability of
the replacement tire as indicated on the above
table.
Remember...High speed driving can be
dangerous and may be damaging to your tires.
And...When driving at highway speeds, correct
inflation pressure is especially important.
(Continued on next page)
IMPORTANT TIRE SAFETY INFORMATION¹

43
Contact the manufacturer of your tires for
their position and assistance on the repair of
speed-rated tires. When you are replacing tires
that have a speed rating, you must replace
with tires of the same or higher speed rating
if the speed capability of the vehicle is to be
maintained.
VISUAL INSPECTION
INSPECT YOUR TIRES. DO NOT DRIVE ON A
DAMAGED TIRE OR WHEEL. Check your tires
frequently for scrapes, bulges, separations,
cuts, snags, cracks, penetrations or excessive
localized wear from hard braking. Also check
for abnormal tire wear, particularly on the
edges of the tire tread which may be caused
by misalignment or underinflation. Impacts
can damage the inner portion of the tire
without being visible on the outside. If damage
can be seen on the tires or wheels, or if you
suspect that possible impact damage may
have occurred, replace with spare at once and
have your tire store or retailer inspect your
tires immediately. Use of a damaged tire could
result in tire destruction. When inspecting
your tires, including the spare, check your air
pressures. If your pressure check indicates
that one of your tires has lost pressure of two
pounds or more, look for signs of penetrations,
valve leakage, or wheel damage that may
account for the air loss.All tires will wear out faster when subjected
to high speeds as well as hard cornering, rapid
starts, sudden stops, frequent driving on roads
which are in poor condition, and off-road use.
Roads with holes and rocks or other objects
can damage tires and cause misalignment of
your vehicle. When you drive on such roads,
drive on them carefully and slowly, and before
driving again at normal or highway speeds,
examine your tires for any damage, such
as cuts, bulges, penetrations, unusual wear
patterns, etc.
TREAD WEAR INDICATORS (WEAR BARS):
Tires contain Tread Wear Indicators (Wear
Bars) in the grooves of the tire tread which
show up when only 2/32nds of an inch
(1.6mm) of tread is remaining. At this stage,
your tires must be replaced. Tires worn beyond
this stage are dangerous.
HAZARDS
Objects in the road that threaten a tire should
be safely avoided. These objects are potholes,
glass, metal, rocks, wood debris and the
like. Unavoidable contact should prompt a
thorough tire inspection.
You may not always recall hitting an object
that can damage or injure your tires. If while
driving your vehicle experiences any unusual
vibrations, ride disturbance or noise and/or you
suspect that possible damage to the tires or
vehicle has occurred, DO NOT JAM OR LOCK
YOUR BRAKES! Rather reduce your speed and
drive with caution until you can safely pull off
the road. Stop and inspect the tires. If the tire is underinflated or damaged, deflate, remove
the tire and rim assembly and replace it with
your spare. If you cannot detect a cause, have
the vehicle towed to the nearest vehicle or tire
retailer to have the vehicle inspected.
REPAIRING, MOUNTING AND
DEMOUNTING OF TIRES
Do not attempt to repair, mount or demount a
tire yourself. Tire changing can be dangerous
and must be done by professionally trained
persons using proper tools and procedures
as specified by the Rubber Manufacturers
Association (RMA). Follow these mounting
recommendations. Your tires should be
mounted on wheels of correct size and type
and which are in good, clean condition. Bent,
chipped or rusted wheels may cause tire
damage. The inside of the tire must be free
from foreign materials. Have your retailer
check the wheels before mounting new tires.
Mismatched tires and rims can explode during
mounting. Also, mismatched tires and rims can
result in dangerous tire failure on the road. If
a tire is mounted by error on the wrong-sized
rim, do not remount it on the proper rim -
scrap it. It may be damaged internally (which
is not externally visible) by being dangerously
stretched and could fail on the highway.
Old valves may leak. When new tubeless tires
are mounted, have new valves of the correct
type installed. Tubeless tires must be mounted
only on wheels designed for tubeless tires, i.e.,
wheels which have safety humps or ledges.
IMPORTANT TIRE SAFETY INFORMATION¹
(Continued on next page)

45
WORN TIRES
Never drive on worn tires. Tires should be
replaced by trained personnel when 2/32nds
of an inch tread depth remains, as indicated
by the tread wear indicators molded into the
tread grooves. In most states, it is illegal to
drive with less than 2/32nds of an inch of
tread remaining.
TIRE MIXING
For best performance select tires similar in
size and load rating to the original equipment
tires. It is recommended that the same size
and type of tire be used on all four wheel
positions. In certain tires, casing ply material
and ply construction may vary as indicated
on the sidewall of the tire. When changing
or replacing tires, it is preferred that all four
tires are the same construction type (i.e.,
High Performance, All Season, Mud & Snow)
and construction (Radial or Bias Ply). Before
mixing tires of different types on a vehicle in
any configuration, be sure to check the vehicle
Owner’s Manual for its recommendations.
Tires which meet the Rubber Manufacturer’s
Association (RMA) definition of mud and
snow tires are marked M/S, M+S, M&S. On
such tires, this designation is molded into the
sidewall. Tires without this notation are not
recommended for mud and/or snow driving.
If snow tires are needed, it is necessary
to select tires equivalent in size and load
rating to the original equipment tires.
Always fit performance snow tires in sets of four (4) for optimum mud & snow traction
and maintenance of vehicle handling
characteristics. If you do not, it may adversely
affect the safety and handling of your vehicle.
It is also important to check the vehicle
Owner’s Manual before mixing or matching
tires on 4-wheel drive vehicles as this may
require special precautions.
Please refer to your Owner’s Manual for more
information on tire replacement precautions. TIRE ROTATION
Tires on your Infiniti vehicle should be rotated
every 7,500 miles or as irregular wear
develops. If irregular wear becomes apparent
or if the wear rate on the tires is perceptibly
uneven, the tires should be rotated in such
a way to alleviate the problem. Check your
vehicle for any mechanical problems and
correct if necessary. Any rotation pattern or
procedure may be followed including those
indicated in the Owner’s Manual. Some tires
have arrows on the sidewall showing the
direction in which the tire should turn. When
rotating this type of tire, care must be taken
to maintain the proper turning direction as
indicated by the arrows. Some vehicles have
different tire sizes specified for front and rear
axles. Tires on these vehicles should not be
rotated side to side (unless they are non-
directional). Where a temporary type spare tire
is available, it should not be included in the tire
rotation schedule. Such tires are intended for
temporary use only.
REPLACING TWO TIRES
If your vehicle was originally equipped with
four tires that were the same size and you are
only replacing two of the four tires, install the
new tires on the rear axle. Placing new tires
on the front axle may cause loss of vehicle
control in some driving conditions and cause
an accident and personal injury.
TRAILER TOWING
If you anticipate towing a trailer, you should
see a tire retailer for advice concerning the
correct size of tire and pressure. Tire size and
pressure will depend on the type and size of
the trailer and hitch utilized, but in no case
must the maximum cold inflation pressure or
the tire load rating be exceeded. Check the tire
decal and your Owner’s Manual for further
recommendations on trailer towing.
TIRE ALTERATIONS
Do not perform any alterations on your tires.
Alterations may prevent proper performance,
leading to tire damage, which can result in an
accident. Tires which become unserviceable
due to alterations such as truing, whitewall
inlays, addition of balancing or sealant liquids,
may be excluded from warranty coverage.
Consult your tire warranty.
(Continued on next page)
IMPORTANT TIRE SAFETY INFORMATION¹