2020 FORD F-250 open hood

3. Raise the hood until the lift cylinders
hold it open.
4. To close, lower the hood and make sure that it is closed properly and fully
latched.
UNDER HOOD OVERVIEW - 6.2L Battery. See Changing the 12V Battery (page 368).
A.
Engine compartment fuse box. See
Fuse Specification Chart (page 329).
B.
Engine oil dipstick. See
Engine Oil Dipstick (page 341).
C.
338
Super Duty (TFE), enUSA, Edition date: 201909, Third-Printing- MaintenanceE190266 E330427

5. Open the hood. See Opening and
Closing the Hood (page 337).
6. Remove the dipstick and wipe it with a clean, lint-free cloth. For 6.2L V8 See
Under Hood Overview
(page 338).
7. Replace the dipstick and remove it again to check the oil level. See
Engine Oil Dipstick
(page 341).
8. Make sure that the oil level is between
the maximum and minimum marks. If
the oil level is at the minimum mark,
add oil immediately. See
Capacities
and Specifications (page 429).
9. If the oil level is correct, replace the dipstick and make sure it is fully seated.
Note: Do not remove the dipstick when the
engine is running.
Note: If the oil level is between the
maximum and minimum marks, the oil level
is acceptable. Do not add oil.
Note: The oil consumption of new engines
reaches its normal level after approximately
3,000 mi (5,000 km)
.
Adding Engine Oil WARNING: Do not remove the filler
cap when the engine is running.
Do not use supplemental engine oil
additives because they are unnecessary
and could lead to engine damage that may
not be covered by the vehicle Warranty. Only use oils certified for gasoline engines
by the American Petroleum Institute (API).
An oil with this trademark symbol
conforms to the current engine and
emission system protection standards and
fuel economy requirements of the
International Lubricants Specification
Advisory Committee (ILSAC).
To top up the engine oil level do the
following:
1. Clean the area surrounding the engine
oil filler cap before you remove it.
2. Remove the engine oil filler cap. For 6.2L V8
See Under Hood Overview
(page 338).
3. Only add engine oil that meets our specifications. See
Capacities and
Specifications (page 429).
4. Recheck the oil level.
5. If the oil level is correct, replace the dipstick and make sure it is fully seated.
6. Replace the engine oil filler cap. Turn it clockwise until you feel a strong
resistance.
Note: Do not add oil further than the
maximum mark. Oil levels above the
maximum mark may cause engine damage.
Note: Make sure you install the oil filler cap
correctly.
Note: Soak up any spillage with an
absorbent cloth immediately.
342
Super Duty (TFE), enUSA, Edition date: 201909, Third-Printing- MaintenanceE142732

ENGINE OIL CHECK - 6.7L
DIESEL
To check the engine oil level consistently
and accurately, do the following:
1.
Make sure the parking brake is on. Make
sure the transmission is in park (P) or
neutral (N).
2. Run engine until it reaches normal operating temperature.
3. Make sure that your vehicle is on level ground.
4. Switch the engine off and wait 15 minutes for the oil to drain into the oil
pan. Checking the engine oil level too
soon after you switch the engine off
may result in an inaccurate reading.
5. Open the hood. See Opening and
Closing the Hood (page 337).
6. Remove the dipstick and wipe it with a clean, lint-free cloth. See
Under
Hood Overview (page 339).
7. Replace the dipstick and remove it again to check the oil level. See
Engine Oil Dipstick
(page 341).
8. Make sure that the oil level is between
the maximum and minimum marks. If
the oil level is at the minimum mark,
add oil immediately. See
Capacities
and Specifications (page 446).
9. If the oil level is correct, replace the dipstick and make sure it is fully seated.
Note: Do not remove the dipstick when the
engine is running.
Note: If the oil level is between the
maximum and minimum marks, the oil level
is acceptable. Do not add oil.
Note: The oil consumption of new engines
reaches its normal level after approximately
3,000 mi (5,000 km)
. Adding Engine Oil WARNING: Do not remove the filler
cap when the engine is running.
Do not use supplemental engine oil
additives because they are unnecessary
and could lead to engine damage that may
not be covered by the vehicle Warranty.
To top up the engine oil level do the
following:
1. Clean the area surrounding the engine oil filler cap before you remove it.
2. Remove the engine oil filler cap. See Under Hood Overview
(page 339).
Turn it counterclockwise and remove
it.
3. Add engine oil of the proper viscosity and grade that meets Ford
specifications. See
Capacities and
Specifications (page 446). You may
have to use a funnel to pour the engine
oil into the opening.
4. Recheck the oil level.
5. If the oil level is correct, replace the dipstick and make sure it is fully seated.
6. Replace the engine oil filler cap. Turn it clockwise until you feel a strong
resistance.
Note: Do not add oil further than the
maximum mark. Oil levels above the
maximum mark may cause engine damage.
Note: Make sure you install the oil filler cap
correctly.
Note: Soak up any spillage with an
absorbent cloth immediately.
343
Super Duty (TFE), enUSA, Edition date: 201909, Third-Printing- Maintenance

Engine lubrication for severe
service operation
The following conditions define severe
operation for which engine operation with
SAE 5W-40 oil which meets Ford
specification, WSS-M2C171-F1, is
recommended. Oil and oil filter change
intervals will be determined by the
Intelligent Oil Life Monitor™ as noted
previously.
ENGINE OIL CHECK - 7.3L
To check the engine oil level consistently
and accurately, do the following:
1.
Make sure the parking brake is on. Make
sure the transmission is in park (P) or
neutral (N).
2. Run the engine until it reaches normal operating temperature.
3. Make sure that your vehicle is on level ground.
4. Switch the engine off and wait 15 minutes for the oil to drain into the oil
pan. Checking the engine oil level too
soon after you switch the engine off
may result in an inaccurate reading.
5. Open the hood. See Maintenance
(page 337).
6. Remove the dipstick and wipe it with a clean, lint-free cloth. See
Maintenance
(page 337).
7. Replace the dipstick and remove it again to check the oil level. See
Maintenance
(page 337).
8. Make sure that the oil level is between
the maximum and minimum marks. If
the oil level is at the minimum mark,
add oil immediately. See
Capacities
and Specifications (page 429).
9. If the oil level is correct, replace the dipstick and make sure it is fully seated. Note:
Do not remove the dipstick when the
engine is running.
Note: If the oil level is between the
maximum and minimum marks, the oil level
is acceptable. Do not add oil.
Note: The oil consumption of new engines
reaches its normal level after approximately
3,000 mi (5,000 km)
.
Adding Engine Oil WARNING: Do not remove the filler
cap when the engine is running.
Do not use supplemental engine oil
additives because they are unnecessary
and could lead to engine damage that may
not be covered by the vehicle Warranty. Only use oils certified for gasoline engines
by the American Petroleum Institute (API).
An oil with this trademark symbol
conforms to the current engine and
emission system protection standards and
fuel economy requirements of the
International Lubricants Specification
Advisory Committee (ILSAC).
To top up the engine oil level do the
following:
1. Clean the area surrounding the engine
oil filler cap before you remove it.
2. Remove the engine oil filler cap.
344
Super Duty (TFE), enUSA, Edition date: 201909, Third-Printing- MaintenanceE142732

4. Remove the auxiliary foam filter from
the air filter housing.
5. To install, reverse the removal procedure. The housing cover can be
oscillated slightly left to right to assist
with installation as needed, until
positioned such that all three clips can
be re-engaged.
Air Filter Restriction Gauge The air filter restriction gauge is in the
upper housing of the air filter assembly. Check the air filter restriction gauge
whenever you open the hood to carry out
general engine maintenance or at least
every 7,500 mi (12,000 km). If you operate
your vehicle in extremely dusty conditions,
check the gauge at least every 500 mi
(800 km) or two weeks, whichever occurs
first. Change the air filter element when
the restriction gauge reads near the
change filter line and the gauge is yellow.
Allowing the restriction gauge to reach
maximum affects engine performance and
fuel economy.
Operating your vehicle in heavy snowfall
or extreme rain conditions may allow
excessive amounts of snow or water into
the air intake system. This could restrict air
flow and cause the engine to lose power
or shut down.
After installing a new air filter element, you
must reset the gauge by pressing the reset
button.
After operating your vehicle during heavy
snowfall or extreme rain, do the following:
• Snow: At the earliest opportunity, open
the hood and clear any snow and ice
from the air filter housing inlet and
reset the air filter restriction gauge.
• Extreme rain: The air filter element
dries out after approximately 15– 30
minutes of driving at highway speeds.
At the earliest opportunity, open the
hood and reset the air filter restriction
gauge.
Note: Do not remove the foam filter.
348
Super Duty (TFE), enUSA, Edition date: 201909, Third-Printing- Maintenance E310420

ADJUSTING THE HEADLAMPS
Vertical Aim Adjustment
The headlamps on your vehicle are
properly aimed at the assembly plant. If
your vehicle has been in an accident, the
alignment of your headlamps should be
checked by your authorized dealer.
Headlamp Aiming Target
8 feet (2.4 meters)
A
Center height of lamp to ground
B
25 feet (7.6 meters)
C
Horizontal reference line
D
Vertical Aim Adjustment Procedure
1. Park the vehicle directly in front of a wall or screen on a level surface,
approximately 25 ft (7.6 m) away.
2. Measure the height of the headlamp bulb center from the ground and mark
an
8 ft (2.4 m) horizontal reference line
on the vertical wall or screen at this
height.
Note: To see a clearer light pattern for
adjusting, you may want to block the light
from one headlamp while adjusting the
other. 3. Turn on the low beam headlamps to
illuminate the wall or screen and open
the hood. 4. On the wall or screen you will observe
a flat zone of high intensity light
located at the top of the right hand
portion of the beam pattern. If the top
edge of the high intensity light zone is
not at the horizontal reference line, the
headlamp will need to be adjusted. 5. Locate the vertical adjuster on each
headlamp. Using a Phillips #2
screwdriver, turn the adjuster either
clockwise or counterclockwise in order
to adjust the vertical aim of the
headlamp.
Note: A. LED headlamp.
370
Super Duty (TFE), enUSA, Edition date: 201909, Third-Printing- MaintenanceE142592 E142465 A
B
E223774

Accessing the Phone Features.....................
476
Accessing the Settings Menu........................ 476
Accessing the Sound Settings...................... 476
Adjusting the Volume....................................... 477
Changing Radio Stations................................. 477
Listening to the Radio....................................... 477
Playing or Pausing Media................................ 477
Switching Radio Text On and Off.................477
Switching Repeat Mode On and Off...........477
Switching Shuffle Mode On and Off...........477
Switching the Audio Unit On and Off.........477
Switching the Display On and Off................477
Using Seek, Fast Forward and Reverse............................................................. 478
Using the Display Control............................... 478
Using the Number Block................................. 478
Autolamps........................................................87 Windshield Wiper Activated
Headlamps........................................................ 87
Automatic Climate Control......................140 Directing the Airflow......................................... 140
Setting the Blower Motor Speed................... 141
Setting the Temperature.................................. 141
Switching Auto Mode On and Off.................141
Switching Dual Zone Mode On and Off........................................................................\
. 141
Switching Maximum Air Conditioning On and Off................................................................ 141
Switching Maximum Defrost On and Off........................................................................\
. 141
Switching Recirculated Air On and Off........................................................................\
142
Switching the Air Conditioning On and Off........................................................................\
. 141
Switching the Climate Control On and Off........................................................................\
. 141
Automatic High Beam Control..................92
Automatic High Beam Control Indicators........................................................92
Automatic Transmission
...........................201
Brake-Shift Interlock........................................ 204
For F350, F450, F550 and F600 Chassis Cab Vehicles................................................... 204
If Your Vehicle Gets Stuck in Mud or Snow................................................................. 205
Understanding the Shift Positions of Your Automatic Transmission............................. 201Understanding Your SelectShift
Automatic ™ Transmission....................... 202
Automatic Transmission Fluid Check............................................................365
Autowipers
.......................................................84
Auxiliary Power Points................................162 400 Watt AC Power Point............................... 162
DC Power Point................................................... 162
Locations............................................................... 163
Auxiliary Switches
.......................................547
Upfitter Interface Module............................... 550
B
Battery See: Changing the 12V Battery..................... 368
Bed Extender
....................................................72
Grocery mode........................................................ 74
Tailgate mode........................................................ 73
Bed Ramps....................................................269 Installing the Ramp Holder............................. 271
Stowing the Bed Ramp..................................... 271
Using the Bed Ramp......................................... 270
Blind Spot Information System
.............248
Blind Spot Information System with Trailer
Tow.................................................................... 250
Switching the System Off and On...............252
System Errors...................................................... 252
Using the System.............................................. 249
BLIS See: Blind Spot Information System..........248
Bonnet Lock See: Opening and Closing the Hood...........337
Booster Seats
...................................................31
Types of Booster Seats...................................... 32
Brake Fluid Check........................................366 Brake Fluid Service Interval............................ 367
Brakes................................................................217 General Information........................................... 217
Breaking-In.....................................................310
Bulb Specification Chart...........................467
C
Canceling the Set Speed..........................225
Capacities and Specifications - 6.2L
.................................................................437
Air Conditioning System.................................. 437
614
Super Duty (TFE), enUSA, Edition date: 201909, Third-Printing- Index

Turbo Boost Gauge............................................
103
Type 1 and 2........................................................... 101
Type 3...................................................................... 102
Gearbox See: Transmission.............................................. 201
General Information on Radio Frequencies...................................................53
Intelligent Access................................................. 53
General Maintenance Information........553 Multi-Point Inspection..................................... 556
Owner Checks and Services.......................... 554
Protecting Your Investment........................... 553
Why Maintain Your Vehicle?.......................... 553
Why Maintain Your Vehicle at Your Dealership?..................................................... 553
Getting Assistance Outside the U.S. and Canada.........................................................325
Getting the Services You Need...............322 Away From Home.............................................. 322
Global Opening...............................................95
Opening the Windows....................................... 95
H
Handbrake See: Parking Brake..............................................219
Hazard Flashers
............................................316
HDC See: Using Hill Descent Control................... 226
Headlamp Adjusting See: Adjusting the Headlamps..................... 370
Headrest See: Head Restraints......................................... 147
Head Restraints.............................................147 Adjusting the Head Restraint......................... 148
Heated Exterior Mirrors..............................144
Heated Rear Window..................................144
Heated Seats
.................................................156
Rear Heated Seats............................................. 156
Heated Steering Wheel
................................81
Heated Windshield......................................144
Windshield Wiper De-Icer............................... 144
Heating See: Climate Control......................................... 139
Hill Start Assist
..............................................219
Switching the System On and Off..............220
Using Hill Start Assist...................................... 220Hints on Controlling the Interior Climate
- Vehicles With: Automatic
Temperature Control................................142
Defogging the Side Windows in Cold Weather............................................................. 143
General Hints........................................................ 142
Quickly Cooling the Interior............................. 143
Quickly Heating the Interior............................ 142
Recommended Settings for Cooling...........143
Recommended Settings for Heating..........143
Hints on Controlling the Interior Climate - Vehicles With: Manual Temperature
Control...........................................................143
Defogging the Side Windows in Cold Weather............................................................. 144
General Hints........................................................ 143
Quickly Cooling the Interior............................. 143
Quickly Heating the Interior............................ 143
Recommended Settings for Cooling...........143
Recommended Settings for Heating..........143
Vehicle Stationary for Extended Periods During Extreme High Ambient
Temperatures.................................................. 144
Hints on Driving With Anti-Lock Brakes............................................................219
Hood Lock See: Opening and Closing the Hood...........337
Horn.....................................................................82
I
Ignition Switch
...............................................168
In California (U.S. Only).............................323
Information Display Control........................81
Information Displays...................................109 General Information.......................................... 109
Information Messages................................120 4WD........................................................................\
. 137
Active Park............................................................ 120
Adaptive Cruise Control.................................... 121
Adaptive Steering............................................... 122
AdvanceTrac and Traction Control..............122
Airbag...................................................................... 123
Alarm and Security............................................. 123
Automatic Engine Shutdown......................... 123
Battery and Charging System........................ 124
Blind Spot Information and Cross Traffic Alert System.................................................... 124
620
Super Duty (TFE), enUSA, Edition date: 201909, Third-Printing- Index