2020 CHRYSLER VOYAGER four wheel drive

The maximum load rating of your tires is molded on the tire sidewall. Do
not exceed this rating. Follow the loading instructions of the manufac-
turer of your vehicle and this will ensure that your tires are not
overloaded. Tires which are loaded beyond their maximum allowable
loads for the particular application will build up excessive heat that may
result in sudden tire destruction.
Do not exceed the gross axle weight rating for any axle on your vehicle.
TRAILER TOWING
If you anticipate towing a trailer, you should visit any BFGoodrich® tire
retailer for advice concerning the correct size tire and pressures. Tire size
and pressures will depend upon the type and size of trailer and hitch
utilized, but in no case must the maximum cold inflation pressure or tire
load rating be exceeded. Check the tire decal and the owner ’s manual
supplied by the manufacturer of your vehicle for further recommenda-
tions on trailer towing.
WHEEL ALIGNMENT AND BALANCING ARE IMPORTANT FOR
SAFETY AND MAXIMUM MILEAGE FROM YOUR TIRES CHECK
HOW YOUR TIRES ARE WEARING AT LEAST ONCE EACH
MONTH
If your tires are wearing unevenly, such as the inside shoulder of the tire
wearing faster than the rest of the tread, or if you detect excessive
vibration, your vehicle may be out of alignment or balance. These
conditions not only shorten the life of your tires but adversely affect the
handling characteristics of your vehicle, which could be dangerous. If
you detect irregular wear or vibration, have your alignment and balance
checked immediately. Tires which have been run underinflated will show
more wear on the shoulders than in the center of the tread.
TIRE MIXING
BFGoodrich® tires are radial tires and for best performance it is recom-
mended that the same size and type of tire be used on all four wheel
positions. Before mixing tires of different types in any configuration on
any vehicle, be sure to check the vehicle manufacturer ’s Owner‘s Manual
for its recommendations.
It is especially important to check the vehicle manufacturer ’s owner ’s
manual when mixing, matching or replacing tires on 4-wheel drive
vehicles, as this may require special precautions.
BFGOODRICH TIRES
37

BFGOODRICH TIRES
FULL-SIZESPARE
Full-size
spare
tires
(not
temporary
spares)
of
the
same
size
and
construc-
tion
should
be
used
in
a
five
(5)
tire
rotation.
Always
check
the
inflation

pressure
of
the
full-size
spare
immediately
before
incorporating
it
into

rotation.
Follow
the
vehicle
manufacturer ’s
recommended
pattern
for

rotation,
or
if
not
available,
see
a
qualified
tire
technician.
REPLACEMENT
OF
TWO
(2)


TIRES
It
is
recommended
that
all
four
(4)
tires
are
replaced
at
the
same
time.

However,
whenever
only
two
tires
are
replaced,
the
new
ones
should
be

put
on
the
rear.
The
new
tires,
with
deeper
tread,
may
provide
better
grip

and
water
evacuation
in
wet
driving
conditions.
CUSTOMIZATION OF TIRES, WHEELS, ORSUSPENSION ON
SUVS ANDLIGHT TRUCKS
Due
to
their
size,
weight
and
higher
center
of
gravity,
vehicles
such
as

SUVs
and
light
trucks
do
not
have
the
same
handling
characteristics
as

automobiles.
Because
of
these
differing
characteristics,
failure
to
operate

your
SUV/truck
in
a
proper
and
safe
manner
can
increase
the
likelihood

of
vehicle
rollover.
Modifications
to
your
SUV/truck
tire
size,
tir
e
type,

wheels
or
suspension
can
change
its
handling
characteristics
and
further

increase
the
likelihood
of
vehicle
rollover.
Whether
your
SUV/truck
has

the
original
equipment
configuration
for
tires,
wheels
and
suspension
or

whether
any
of
these
items
have
been
modified,
always
drive
safely,

avoid
sudden,
sharp
turns
or
lane
changes
and
obey
all
traffic
laws.

Failure
to


do
so
may
result
in
loss
of
vehicle
control
leading
to
an
accident

and
serious
injury
or
death.
TIRE
ALTERATIONS
Do
not
make
or
allow
to
be
made
any
alterations
on
your
tires.

Alterations
may
prevent
proper
performance,
leading
to
tire
damage

which
can
result
in
an
accident.
Tires
which
become
unserviceable
due
to

alterations
such
as
truing,
whitewall
inlays,
addition
of
balancing
or

sealant
liquids,
or
the
use
of
tire
dressing
containing
petr

oleum
distillates

are
excluded
from
warranty
coverage.
39

5 PSI from the previous pressure check, have the tire inspected at once
by an authorized PAX System Retailer for PAX tires or a participating
Michelin tire retailer (or representative of your vehicle manufacturer if
your vehicle owner ’s manual so advises.) Failure to do so may cause
irreparable damage to the tire and result in sudden tire destruction and
personal injury.
TIRE PRESSURE MONITORING SYSTEMS (TPMS):
Your vehicle may be equipped with a Tire Pressure Monitoring System
(TPMS) that is designed to monitor the pressure of tires mounted on your
vehicle and sends a signal to the driver if a tire pressure falls below a
predetermined level. A TPMS should not replace monthly manual
pressure checks for all four (4) tires and the spare. We recommend that
you manually monitor and check tire pressure inflation with a pressure
gauge. Your tires should have the recommended pressure listed by your
vehicle’s manufacturer. This information can be found in the vehicle
owner ’s manual and often on a placard located in the vehicle’s door
jamb, inside the fuel hatch, or on the glove compartment door. If you
have a plus size fitment that requires a higher inflation pressure, your tire
pressure monitoring system will require re-calibration to new inflation
pressure. Refer to your tire dealer/installer of plus size tires for proper
inflation pressure.
We recommend checking air pressure once each month, and before a long
trip. Whether you have a full-sized or mini-spare, make sure that it is
properly inflated as well. If the TPMS generates improper monitoring or
signals we recommend that you consult your owner ’s manual provided
with your vehicle and follow-up with your vehicle’s manufacturer.
TIRE SPINNING
Do not spin wheels in excess of 35 mph (55 km/h) as indicated on the
speedometer. Excessive speed in a free-running, unloaded tire can cause
it to “explode” from centrifugal force. The energy released by such an
explosion is sufficient to cause serious physical injury or death. Never
allow anyone to stand near or behind the spinning tire.
When in mud, sand, snow, ice or other slippery conditions, do not engage
in excessive wheel spin. Accelerating the motor excessively, particularly
with automatic transmission vehicles, may cause a drive tire that has lost
traction to spin beyond its speed capability. This is also true when
balancing a drive tire/wheel assembly on the vehicle using the vehicle
engine to spin the tire/wheel assembly.
MICHELIN
171

checked
immediately.
Ti re s
which
have
been
run
underinflated
will
show

more
wear
on
the
shoulders
than
in
the
center
of
the
tread.
TIRE MIXING
MICHELIN®
tires
are
radial
tires
and
for
best
performance
it
is
recom-
mended
that
the
same
size
and
type
of
tire
be
used
on
all
four
wheel

positions.
Before
mixing
tires
of
different
types
in
any
configuration
on

any
vehicle,
be
sure
to
check
the
vehicle
manufacturer ’s
owner‘s
manual

for
its
recommendations.
It
is
especially
important
to
check
the
vehicle
manufacturer ’s
owner’s



manual
when
mixing,
matching,
or
replacing
tires
on
4-wheel
drive

vehicles,
as
this
may
require
special
precautions.
MICHELIN
DOES
NOT
RECOMMEND
MIXING
PAX®
SYSTEM
TIRES

WITH
NON-PAX
TIRES
/
SELF-SUPPORTING
ZERO
PRESSURE
(ZP)

TIRES
WITH
NON-ZP
TIRES
OTHER
THAN
THE
TEMPORARY
USE

OF
THE
SPARE
IF
THE
VEHICLE
IS


SO
EQUIPPED.
:,17(5 DRIVING
Ti re s
which
meet
the
Rubber
Manufactures
Association
(RMA)
definition

of
snow
tires
are
marked
M/S,
or
M&S.
On
such
tires,
this
designation
is

molded
into
the
sidewall.
Tires
without
this
notation
are
not
recom-
mended
or

driving.
While
All-Season
tires
are
designed
to
provide
reliable

performance
in
some

conditions,
the
use
of
four

(4)

tires
is
recommended
for
optimal
performance.

Tires
designate
for
use
in
severe

conditions
are

marked
on
at
leas
one
sidewall
with
the
letter
“M”
TIRE ROTATION AND REPLACEMENT
To obtain maximum tire wear, it may be necessary to rotate your tires.
Refer to your vehicle owner ’s manual for instructions on tire rotation. If
you do not have an owner‘s manual for your vehicle, Michelin recom-
mends rotating your tires every 6,000 to 8,000 miles (10,000 to 12,000 km).
Monthly inspection for tire wear is recommended. Your tires should be
rotated at the first sign of irregular wear, even if it occurs before 6,000
miles (10,000 km). This is true for all vehicles.
MICHELIN
177

When rotating tires with a directional tread pattern, observe the arrows
molded on the sidewall which show the direction the tire should turn.
Care must be taken to maintain the proper turning direction.
Some Tire Pressure Monitoring Systems (TPMS) may not recognize
that a tire has been moved to a different position on your vehicle. Make
certain that your TPMS system is reset, if necessary, so as to correctly
identify the location of each tire on your vehicle. Refer to your vehicle
owner ’s manual or your vehicle dealer.
Determine whether rotated tires require tire inflation adjustment as front
and rear position tire pressure may vary according to the vehicle
manufacturer ’s specification due to the actual load on that wheel
position. Some vehicles may have different sized tires mounted on the
front and rear axles, and these different sized tires have rotation
restrictions. Always check the vehicle owner ’s manual for the proper
rotation recommendations.
Full-size Spare
Full-size spare tires (not temporary spares) of the same size and construc-
tion should be used in a five (5) tire rotation. Always check the inflation
pressure of the full-size spare immediately before incorporating it into
rotation. Follow the vehicle manufacturer ’s recommended pattern for
rotation, or if not available, see a qualified tire technician.
Replacement of Two (2) Tires
It is recommended that all four (4) tires are replaced at the same time.
However, when only two tires are replaced, the new tires should be put
on the rear. The new tires, with deeper tread, may provide better grip and
water evacuation in wet driving conditions.
CUSTOMIZATION OF TIRES, WHEELS, OR SUSPENSION ON
SUVS AND LIGHT TRUCKS
Due to their size, weight and higher center of gravity, vehicles such as
SUVs and light trucks do not have the same handling characteristics as
automobiles. Because of these differing characteristics, failure to operate
your SUV/truck in a proper and safe manner can increase the likelihood
of vehicle rollover. Modifications to your SUV/truck tire size, tire type,
wheels or suspension can change its handling characteristics and further
increase the likelihood of vehicle rollover. Whether your SUV/truck has
the original equipment configuration for tires, wheels and suspension or
whether any of these items have been modified, always drive safely,
MICHELIN178

PIRELLITIRES
5.DOT Street Legal Competition Tires
P
Zero
Trofeo
and
P
Zero
Corsa
tire
lines
use
special
tire
construction
and

compounds
to
achieve
their
distinctive
performance
in
dry
conditions.
As

a
result
of
that,
their
performance
in
cold
temperatures,
heavy
rain
or

standing
water
will
be
decreased.
Use
extreme
caution
and
drive
slowly

on
wet
roads.
The
minimum
tread
depth
will
be
r
eached
earlier
than
normal
road
tires,

resulting
in
reduced
tread
life.
6.Winter Tires
The
standard
Pirelli
tires
may
be
effective
in
light
snow
conditions.

However,
for

use,
you
may
wish
to
install

tires.

During

use,
Pirelli
strongly
recommends
the
fitment
of
4


tires.
Please
check
your
vehicle
owner ’s
manual
concerning


tire
size
recommendation.
If
the

tires
have
a
lower

speed
rating
than
the
original
equipment
tires,
vehicle
handling
may

be
affected,
and
the
vehicle
maximum
speed
must
be
reduced
to
the


tire
speed
rating.
Pirelli
requires
that
studded
tires
be
installed
on
all
four
positions.

Installing
studded
tires
only
on
the
drive
positions
of
any
vehicle,

including
a
front
wheel
drive
vehicle,
may
cause
adverse
handling

characteristics.
7. Run FlatTires
Always
refer
to
the
vehicle
owners’
manual
with
respect
to
specific
safety

and
operating
information
relating
to
the
vehicle.
Damaged
Run
Flat
tires

or
Run
Flat
tires
that
have
experienced
a
loss
of
pressure
should

immediately
be
replaced
with
another
Run
Flat
tire
of
identical
size
and

Service
Description
(Load
Index
and
Speed
Symbol).
Run
Flat
tires
have
been
developed
based
on
the
specifications
of
the

vehicles
on
which
they
are
mounted.
Accordingly,
Run
Flat
tires
should



only
be
mounted
on
vehicles
specifically
manufactured
to
accommodate

Run
Flat
tires.
Run
Flat
tires
must
be
mounted
in
conjunction
with
a
functional
Tire

Pressure
Monitoring
System
(TPMS).
The
mounting
of
tires
and
installation
of
the
Tire
Pressure
Monitoring

System
(TPMS)
should
be
carried
out
by
a
specialized
dealer.
210

8. Tire Replacement
The tires fitted to your vehicle as original equipment were tested and
approved by the vehicle manufacturer and the tire manufacturer and take
into account all aspects of the vehicle’s operation. Changes in the tire size,
type or construction should not be made without seeking advice from the
vehicle or tire manufacturer or an authorized Pirelli dealer since unap-
proved tires on your vehicle could adversely affect steering, handling,
braking and traction. The tire information (tire size, load index and speed
symbol) as found on the vehicle placard or in the owner ’s manual should
always be followed when replacing tires.
It is strongly recommended that Pirelli tires be mounted in sets of four
with the same tread type. Pirelli tires should not be mixed with other tire
brands. It is necessary to follow this procedure because different tire
constructions have different handling characteristics. Tires on the same
axle must be the same manufacturer, brand, tire size, load index, speed
rating and Pirelli part number.
When changing only two tires on a vehicle which is homogeneously
fitted (four tires of the same tire size), fit the new tires on the rear axle.
This applies to all vehicles regardless of their drive axle. (Front or Rear
Drive).
On all wheel drive or four wheel drive vehicles the tires must always be
replaced in sets of four.
When replacing tires on light truck vehicles, you should always follow
the vehicle manufacturer ’s recommendations. Passenger and light truck
tires are not interchangeable, due to differences in their pressures and
load carrying capacity.
P-Metric and Euro-metric Interchangeability: Euro-metric (Example: 225/
45R17) tires have a load index which is equal to or greater than that of the
same size P-metric (Example: P225/45R17) tire. Therefore, they have the
same or higher load carrying capacity at the maximum rated inflation
pressure. Always check with your tire dealer or Pirelli Tire Consumer
Affairs to be sure of the exact interchangeability to maintain proper
vehicle dynamics.
Please be aware that it is important that, before fitting the suggested tires,
the fitment is allowed by the technical specifications of the vehicle, the
vehicle manufacturer and the relevant homologations. Pirelli Tire does
not express any view as to the compatibility of the wheel/tire combina-
tion with the technical specifications for the chassis and vehicle.
PIRELLI TIRES
211

of the replacement tire. Vehicle handling could also be affected.
Consult the vehicle Owner ’s Manual or tire manufacturer for
recommendations.
• If tires with different speed ratings are used, it is recommended that
the lowerspeed- rated tires always be placed on the front axle. This is
to prevent a potential oversteer condition.
FOUR-WHEEL DRIVE (4WD) AND ALL-WHEEL DRIVE (AWD)
VEHICLES
If no instructions for tire mixing appear in the vehicle Owner ’s Manual,
follow these guidelines:
•Do

not
mix
tire
sizes.
All
four
tires
must
be
marked
with
the
same
tire

size,
unless
otherwise
specified
by
the
vehicle
manufacturer.
This
also

applies
to
/snow
tires.
• Do not mix tread pattern types such as all-terrain and all- season.
STUDLESS WINTER/SNOW TIRES
•It

is
always
preferable
to
apply
/snow
tires
to
all
wheel

positions,
including
dual
tires,
to
maintain
vehicle
mobility
and

control.
• If

/snow
tires
are
applied
to
the
front
axle
of
any
vehicle,

/snow
tires
must
also
be
installed
on
the
rear
axle.
DO
NOT

apply
/snow
tires
only
to
the
front
axle.
This
applies
to
all

passenger
and
light
truck
vehicles,
including
front-wheel-
drive,
4WD,

and
AW
D
vehicles.
• If

/snow
tires
are
installed
on
the
rear
axle
of
any
vehicle,
it
is

recommended
(but
not
required)
that
they
also
be
installed
on
the
front

axle.
WARNING!
Unless
/snow
tires
on
the
rear
axle
have
comparable
traction

qualities
to
the
tires
on
the
front
axle,
the
vehicle
may
experience

adverse
handling
characteristics.
This
may
result
in
loss
of
vehicle

control,
which
can
lead
to
serious
personal
injury
or
death.
TOYO TIRES – LIMITED WARRANTY
237