2020 AUDI A3 set clock

8V2012721BK
Power top

Step 2: Lift the power top storage
compartment lid out
Applies to: vehicles with power top

B8V-0285

Fig. 42 Lifting the power top storage compartment lid out
and setting up the supports

B8V-0286



Fig. 43 Power top storage compartment lid: supports set
up
> Raise the power top storage compartment lid
out of the power top compartment and hold it
in place @ & A\ in General information on
page 40.
> Secure the power top storage compartment lid
by pressing on the side supports on both
sides 2).
Z\ WARNING
— Always make sure that the side supports on
the open power top storage compartment
lid are in place, even when the power top is
not fully open or closed. Otherwise, the
power top storage compartment lid could
fall, which increases the risk of an accident.
— Avoid touching the support rods and other
moving parts when opening the power top
storage compartment lid. If do you make
contact, your hands could be pinched.



Step 3: Open the locking pin
Applies to: vehicles with power top
— oO Nx
g 3 a a

~~" “Se
Fig. 44 Rear of the vehicle: opening the locking pin
> Remove the cap on the trip and insert the
wheel wrench into the opening.
> Turn the wheel wrench clockwise until it stops
to open the locking pin.
» Remove the wheel wrench.
Step 4: Close the power top
Applies to: vehicles with power top
2 © Nx
gz > @ oO


B8V-0289

Fig. 46 Rear of the vehicle: lowering the edge of the power
top
> Position yourself near the vehicle.
> Hold the power top by its front edge and pull it
out completely = fig. 45 > A\ in General infor-
mation on page 40.
41
>

System settings

System settings
Setting the date and
time
You can set the clock time manually or using the
GPS*.

> Select: [MENU] button > Settings > left control
button > MMI settings > Date & time, or:
> Select: [MENU] button > Vehicle > left control
button > Vehicle settings > Date & time.


Automatic setting
When this function is switched on ¥, the time
and date are automatically set.
Time
Requirement: the Automatic setting must be
switched off.
Press the control knob. You can set the Time
manually by turning and pressing the control
knob.
Date
Requirement: the Automatic setting must be
switched off.
Press the control knob. You can set the Date
manually by turning and pressing the control
knob.
Time zone
When selecting the appropriate time zone, a
sampling of countries in this zone will be listed.
Automatic time zone*
When this function is switched on ¥, the time
will automatically adjust to the corresponding
time zone.
Automatic daylight saving time*
When this function is switched on M, the time
will automatically switch to daylight saving time.

) The Qi standard makes it possible to charge your mobile
device wirelessly.
230
Time format
If you select 24h, the clock will display, for exam-
ple, 13:00. If you select AM/PM, the clock will
display, for example, 1:00 PM.
Date format
If you select DD.MM.YYYY, the date display will
show, for example, 31.03.2019. If you select
MM/DD/YYYY, the date display will show, for ex-
ample, 03/31/2019. If you select YYYY-MM-DD,
the date display will show, for example,
2019-03-31.
MMI settings

> Select: [MENU] button > Settings > left control
button > MMI settings.

Language
You can change the display language as well as
the language for the voice guidance* and voice
recognition system*.
The number of languages available depends on
the country.
Measurement units
The following measurement units can be set de-
pending on availability: Speed, Distance, Tem-
perature, Fuel consumption, Volume, Pressure.
Mobile device reminder signal
Applies to: vehicles with Audi phone box
Requirement: your cell phone must be Qi-capa-
ble ) or connected to the Audi music interface @
with a USB adapter cable > page 171, fig. 162.
When the device reminder signal is switched on,
you will be notified that your mobile device is still
in the Audi phone box when you leave the vehicle.
You can select between Spoken cue, Signal tone
and Off.
Mobile device reminder signal volume: you can
adjust the reminder signal volume by turning the
control knob.

Emergency assistance

Removing the wheel
>» Use the hexagonal socket in the screwdriver
handle to completely remove the topmost
wheel bolt and set it aside on a clean surface
> fig. 273.
> Screw the threaded end of the alignment pin
from the tool kit hand-tight into the empty bolt
hole > fig. 274.
> Then remove the other wheel bolts as described
above.
> Take off the wheel leaving the alignment pin in
the bolt hole >@).
Putting on the compact spare wheel
> Lift the spare wheel and carefully slide it over
the alignment pin to guide it in place >@.
> Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel bolts
slightly.
> Remove the alignment pin and insert and tight-
en the remaining wheel bolt slightly like the
rest.
> Turn the jack handle counter-clockwise to lower
the vehicle until the jack* is fully released.
> Use the wheel bolt wrench to tighten all wheel
bolts firmly > page 353. Tighten them cross-
wise, from one bolt to the (approximately) op-
posite one, to keep the wheel centered.
@) Note
When removing or installing the wheel, the
rim
could hit the brake rotor and damage the
rotor. Work carefully and have a second per-
son help you.
G) Tips
Never use the hexagonal socket in the handle
of the screwdriver to loosen or tighten the
wheel bolts.
— Pull the reversible blade from the screwdriv:
er before you use the hexagonal socket in
the handle to turn the wheel bolts.
— When mounting tires with unidirectional
tread design make sure the tread pattern is
pointed the right way > page 356.
— The wheel bolts should be clean and easy to
turn. Check for dirt and corrosion on the
356
mating surfaces of both the wheel and the
hub. Remove all dirt from these surfaces be-
fore remounting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction.
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare tire with a tread pattern in-
tended for use in a specific direction, please note
the following:
— The direction of rotation is marked by an arrow
on the side of the tire.
— If the spare tire has to be installed in the incor-
rect direction, use the spare tire only tempora-
rily since the tire will not be able to achieve its
optimum performance characteristics with re-
gard to aquaplaning, noise and wear.
— We recommend that you pay particular atten-
tion to this fact during wet weather and that
you
adjust your speed to match road condi-
tions.
— Replace the flat tire with a new one and have it
installed on your vehicle as soon as possible to
restore the handling advantages of a unidirec-
tional tire.
Notes on wheel changing
Please read the information > page 326 if you
are going to use a spare tire which is different
from the tires on your vehicle.
After you change a tire:
— Check the tire pressure on the spare immedi-
ately after installation.
— Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos-
sible by your authorized Audi dealer ora
qualified service station.
— With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lbs (120 Nm).

Emergency assistance

Removing the spare tire
Applies to: vehicles with version 1
> Lift up the cargo floor with the plastic handle
until the cargo floor is clamped behind the tabs
on both side panels @) > fig. 275.
> Applies to: vehicles with subwoofer in the spare
wheel well: Remove the subwoofer*. Check
which subwoofer is installed based on the con-
nector: > page 358.
> Turn the handwheel counter-clockwise and re-
move it.
> Remove the spare tire.
Removing the spare tire
Applies to: vehicles with version 2
>
Lift the cargo floor up using the plastic handle.
> Hang the plastic hook on the luggage compart-
ment weather strip @) 9 fig. 275.
> Turn the handwheel counter-clockwise and re-
move it.
> Remove the spare tire.
Snow chains
For technical reasons, the use of snow chains on
the
compact spare tire is not permitted.
If you have to drive with snow chains and a front
tire fails, mount the spare tire in place of a rear
tire. Install the snow chains on the rear tire that
you removed, and install that in place of the
front tire that failed.

ZX WARNING
— After installing a spare tire, the tire pressure
must be checked as soon as possible. The
tire pressure is available on > page 330,
fig. 260
— Do not drive faster than 50 mph (80 km/h)
with a compact spare tire. Driving faster
than that increases the risk of an accident.
—To reduce the risk of an accident, avoid hard
acceleration or braking and driving fast
around curves with the compact spare tire.
—To reduce the risk of an accident, never drive
with more than one compact spare tire.
— Normal summer or winter tires must not be
mounted on the compact spare wheel rim.

358
Removing the subwoofer
Applies to: vehicles with subwoofer in the spare wheel well

The subwoofer must be removed before the
spare wheel* can be removed.
Q
|
S| = & EJ

Fig. 278 Spare tire well: subwoofer (version 2)
Removing the subwoofer (version 1)
> Lift up the cargo floor > page 357, fig. 275.
> Press the connector tabs @) © fig. 277 togeth-
ef.
> Remove the connector (2) and set the discon-
nected cable aside.
> Remove the bolt (3).
> Carefully remove the subwoofer.
Removing the subwoofer (version 2)
> Lift up the cargo floor > page 357, fig. 275.
> Pull the lock @) 9 fig. 278 toward the cable.
> Press the locking tab (2) down.
> Remove the connector (3) and set the removed
cable aside.
> Remove the bolt @).
> Carefully remove the subwoofer.
Installing the subwoofer
> Carefully place the subwoofer in the rim well.
The word “FRONT” on the subwoofer must face
forward.

8V2012721BK

Cell phone
refer to Telephone...........-0eee eee 169
Cell phone compartment
refer to Audi phone box............... 171
Central locking. ...... 0c. sce e cece eee ee 25
Convenience key........-.--. eee eee e ees 28
Convenience opening and closing......... 34
Mechanically unlocking and locking....... 30
MESSAGG% = saws 7 2 ques « 2 mE s F aS « RoE 29
Remote control key..........0 eee eee ee 27
Setting... 26... cece eee eee 29
Central locking switch..............20-0. 29
Gertifications. . « srw. © suscuas «2 soaneue uo wines 377
Changing'the'scale « ssewic « 5 wwe o # eae ¥ eave 18
Charging
refer to Power sourceS.........-- 000 eee 59
Charging clip..............02..00 ee eee 103
Charging the battery (mobile devi-
(o) 171, 217, 218
Charging (plug-in hybrid drive)............ 97
Child restraints
Danger of using child restraints in the front
SGA = s gcse c x secu = 2 Bees & x Sees eo ee 254
Where can I get additional information
about child restraints and their use?..... 297
Child restraint system anchors........... 292
Child safety........ 0.0.0.0... eee eee eee 278
Important safety instructions for using child
Safety S@ats + meus is ewe yo ees es ewww ee 282
Methemamchorshes = sxncams u water « 5 wens «4 ane 294
Tether straps ..... 2... eee eee eee eee 294
Child safety lock
POWErWIRGOWS): « = smu = 2 seems ss mu < ee 33
ReaMmdOOrsts + wena ov nasi 2 v sues oH sean 2 so 33
Child safety seats........ 00... eee eee eee 284
BoostersSeatstin. i. « scm «x score + x mnie so ane 287
Convertible child seats............20.. 285
Convertible locking retractor........... 290
How do I properly install a child safety seat
in my vehicle?......... 02... c eee eae 282
Infantis@atss « s seme x sews 5 a eames 2 oes 284
Installing a child restraint using the LATCH
SyStEM . 2... eee 293
LATGHISYStEM): = sews « « sewn 5 7 noups 4 «eee 293
Mounting and releasing the anchorage
Hook... . eee eee 293
Safety instructions. « «secs + eeee ey vee 282
SOGUTING)s » +: seomen + w enews ¥ views ¥ Hume ae oe 289
Unused safety belts on the rear seat..... 284
Child seats
Lower anchorages..............000005 293
Classic ViQW.. ieee 19
Cleaning ......... eee eee ee eee eee 342
Cleaning/removing ice from windows...... 344
Cleaning Alcantara...............00000. 345
Cleaning artificial leather............... 345
Cleaning carbon components........ 344, 345
Cleaning controls « 2.23 ss eees «epee ee ee 345
Cleaning decorative parts/trim........... 344
Cleaning exhaust tail pipes.............. 344
Cleaning plastic parts...............00. 345
Cleaning textiles...................00. 345
Cleaning the tail lights.................. 343
Cleaning the windshield...............0.. 49
Climate control system
refer to 2-zone deluxe automatic climate
GORTIOL = vem: 2 5 nem cs eR s HERR Ee REE 65, 66
Clock... eee eee eee eee 230
Closing
Convenience closing ess « vewa ss wwe se oex 34
HOO « & sissies sina 6 8 omnis a ewan ow tne 305
Luggage compartment lid............... 31
Panoramic glass roof................055 35
POWOr Opis ss vescine so cose ¥ x essa s mewens Zo a 36
Windows... 1... cee cece cece eee eee eee 33
COASEG sccrozs » vases wv winengs ou eomeeae 6 e exemene 8 78
Cockpit (overview)i. « cscs « erassue x 6 mmcem ae conse 8
Golormnumber. ss ssc xe sees ov eases ao mewn 379
Coming home/Leaving home
refer to Entry/exit lighting.............. 45
Command (voice recognition system) ...... 162
CompartMent Sie. ss coves ov wren «veers wo rare 60
Compass inthe mirror............-000005 52
Compliance. « s seg: ss sees se Rees ee eee as 377
CONNE Chie: « s seen ce sees vs eens + ReeR oe oe 182
Audi connect e-tron services............ 185
Data plans.......... 0... eee eee eee 187
Data Privacy sc se oss s ence ss paeu si eer 372
InfotainMentix «= svesow a 2 wavwe so voscue eo aes 182
Infotainment services............-.00% 183
connect e-tron services...............0- 185
Connection manager.................4. 231
383