2019 YAMAHA MT-09 traction control

Instrument and control functions
4-10
1
2
34
5
6
7
8
9
10
11
12
TIPConsider the following tips to reduce
fuel consumption:
Avoid high engine speeds during
acceleration.

Travel at a constant speed.

Select the transmission gear that
is appropriate for the vehiclespeed.
Transmission gear display
This display shows the selected gear.
The neutral position is indicated by “ ”
and by the neutral indicator light. Drive mode display
This display indicates which drive
mode has been selected: “STD”, “A” or
“B”. (See page 3-1.)
TCS display
This display indicates which traction
control system setting has been select-
ed: “1”, “2” or “OFF”. (See page 3-1.)
Multi-function display
The multi-function display is equipped
with the following:

an odometer

two tripmeters

a fuel reserve tripmeter

an instantaneous fuel consump-
tion display

an average fuel consumption dis-
play

a coolant temperature display

an air intake temperature display

a brightness control display
1. Transmission gear display
2. Neutral indicator light “ ”1
2
1. Drive mode display
1. TCS display
11
1. Multi-function display
1
BS2-9-E2.book 10 ページ ２０１８年８月１０日　金曜日　午前９時３６分

6-1
1
2
3
4
567
8
9
10
11
12
Operation and important riding points
EAU15952
Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.
WARNING
EWA10272
Failure to familiarize yourself with
the controls can lead to loss of con-
trol, which could cause an accidentor injury.
EAUM3632
TIPThis model is equipped with:
a lean angle sensor. This sensor
stops the engine in case of a vehi-
cle turnover. If this happens, the
engine trouble warning light will
come on, but this is not a malfunc-
tion. Turn the vehicle power off
and then back on again to cancel
the warning light. Failing to do so
will prevent the engine from start-
ing even though the engine will
crank when pushing the start
switch.

an engine auto-stop system. The
engine stops automatically if left
idling for 20 minutes. If the engine
stops, simply push the start switchto restart the engine.
EAU77060
Starting the engineIn order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
The transmission is in the neutral
position.

The transmission is in gear with
the clutch lever pulled and the sid-
estand up.
See page 4-26 for more informa-
tion.
1. Turn the key to “ON” and make sure that the start/engine stop
switch is set to “ ”.
The following warning lights and
indicator light should come on for a
few seconds, then go off.
Oil level warning light

Coolant temperature warning
light

Engine trouble warning light

Traction control system indica-
tor light

Immobilizer system indicator
light
The ABS warning light should
come on when the key is turned to
“ON”, and then go off after travel-
BS2-9-E2.book 1 ページ ２０１８年８月１０日　金曜日　午前９時３６分

Index
11-2
1
2
3
4
5
6
7
8
9
101112
Throttle grip free play, checking ........... 7-16
Tires...................................................... 7-17
Tool kit .................................................... 7-2
Traction control system .......................... 3-1
Traction control system indicator light .... 4-6
Traction control system switch ............... 4-4
Troubleshooting .................................... 7-35
Troubleshooting charts ......................... 7-37
Turn signal indicator light........................ 4-5
Turn signal light bulb, replacing ............ 7-34
Turn signal switch ................................... 4-4VValve clearance .................................... 7-17
Vehicle identification number................ 10-1
Vehicle lights ........................................ 7-34WWheel bearings, c hecking .................... 7-30
Wheels.................................................. 7-19YYamalube ............................................. 7-14
BS2-9-E2.book 2 ページ ２０１８年８月１０日　金曜日　午前９時３６分