2019 TOYOTA SEQUOIA remote control

1103-2. Opening, closing and locking the doors
SEQUOIA_OM_USA_OM0C013U_19MY
Back door
◆Wireless remote control
P. 1 0 0
◆Key
Turning the key operates the doors as follows:
Unlocks all the doors
Opens the back window (turn
and hold)
Locks all the doors
Closes the back window (turn
and hold)
Press and hold the switch to open/
close the power back door. If the
back door is locked, unlock it
before operating the power back
door.
A buzzer sounds and the back
door automatically opens and
closes.
Pressing the switch while the back
door is opening/closing stops the
operation.
When the switch is pressed again during the halted operation, the back
door will perform the reverse operation.
Unlocking and locking the back door
Opening/closing the back door wit h the wireless remote control
(vehicles with power back door)

1113-2. Opening, closing and locking the doors
3
Operation of each component
SEQUOIA_OM_USA_OM0C013U_19MY
◆Power back door switch
Press and hold the switch to open/
close the power back door.
A buzzer sounds and the back
door automatically opens and
closes.
Pressing the switch while the back
door is opening/closing stops the
operation.
When the switch is pressed again
during the halted operation, the
back door will perform the reverse
operation.
◆Door lock switch
 P. 1 0 5
◆Back door opener
Raise the back door while
pushing up the back door
opener switch.
◆Wireless remote control
P. 1 1 0
Opening/closing the back door fro m inside the vehicle (vehicles
with power back door)
Opening the back door from outside the vehicle

1123-2. Opening, closing and locking the doors
SEQUOIA_OM_USA_OM0C013U_19MY
◆Back door strap
Lower the back door using the
back door strap and make sure to
push the back door down from the
outside to close it.
◆Power back door switch (If equipped)
Push and hold the switch to close
the back door.
When the back door is not com-
pletely opened, the power back
door may not close by the switch.
A buzzer sounds and the emer-
gency flashers flash twice to indi-
cate that the back door has been
opened/closed.
The back door can be opened even if it is locked. Lock the back door
again when you leave the vehicle. The back door will not lock a uto-
matically after it has bee n opened and then closed.
◆Wireless remote control (veh icles with power back door)
 P. 1 1 0
The rear step bumper is intended
for rear end protection and easier
step-up loading.
Closing the back door from outside the vehicle
Rear step bumper

1363-3. Adjusting the seats
SEQUOIA_OM_USA_OM0C013U_19MY
Each key can be registered to recall your preferred driving position.
■Registering procedure
Record your driving position to button “1” or “2” before perfor ming
the following:
Carry only the key you want to register, and then close the dri ver’s
door.
If 2 or more keys are in the vehicle, the driving position cann ot be
recorded properly.
Check that the shift lever is in P.
Turn the engine switch to “ON” position.
Recall the driving position that you want to record.
While pressing the recalled
button, press and hold the
door lock switch (either lock
or unlock) until the buzzer
sounds.
If the button could not be regis-
tered, the buzzer sounds contin-
uously for approximately 3
seconds.
■
Recall procedure
Make sure that the doors are locked before recalling the drivin g
position. Carry the key that has been registered to the driving
position, and then unlock and open the driver’s door using the
wireless remote control.
The driving position will move to the recorded position (not in cluding the
steering wheel).
If the driving position is in a position that has already been recorded, the
seat and outside rear view mirrors will not move.
Turn the engine switch to the “ACC” or “ON” position, or fasten a
seat belt.
The seat and steering wheel will move to the recorded position.
Memory recall function
1
2
3
4
1
2

2114-3. Operating the lights and wipers
4
Driving
SEQUOIA_OM_USA_OM0C013U_19MY■
Automatic light off system
●When the headlights come on: The headlights and tail lights aut omatically
turn off after 30 seconds when all doors are closed with the en gine switch
turned to the “ACC” or “LOCK” position. (The lights turn off im mediately if
the button on the wireless remote control is pressed after all doors are
locked.)
● When only the tail lights come on: The tail lights turn off aut omatically with
the engine switch turned to the “ACC” or “LOCK” position and th e driver’s
door is opened.
To turn the lights on again, turn the engine switch to the “ON” position, or turn
the headlight switch off once and then back to the or position.
■ Customization
Settings (e.g. light sensor sensitivity) can be changed.
(Customizable features: P. 516)
NOTICE
■To prevent battery discharge
Do not leave the lights on longer than necessary when the engin e is not
running.

3645-4. Other interior features
SEQUOIA_OM_USA_OM0C013U_19MY
Garage door opener
The HomeLink® wireless control system in your vehicle has 3 buttons
which can be programmed to operate 3 different devices. Refer to the
programming methods on the following pages to determine the
method which is approp riate for the device.
HomeLink
® indicator light
Garage door operation indica-
tors
Buttons
■Before programming the HomeLink®
● During programming, it is possible that garage doors, gates, or
other devices may operate. For this reason, make sure that peo-
ple and objects are clear of the garage door or other devices t o
prevent injury or other potential harm.
● It is recommended that a new battery be placed in the remote
control transmitter for mo re accurate programming.
● Garage door opener motors manufactured after 1995 may be
equipped with rolling code pro tection. If this is the case, you may
need a stepladder or other sturdy, safe device to reach the
“Learn” or “Smart” button on the garage door opener motor.
: If equipped
The garage door opener can be programmed to operate garage
doors, gates, entry doors, door locks, home lighting systems,
security systems, and other devices.
HomeLink®

3655-4. Other interior features
5
Interior features
SEQUOIA_OM_USA_OM0C013U_19MY■
Programming the HomeLink®
Steps through must be performed within 60 seconds, otherwise
the indicator light will stop flashing and programming will not be able to be
completed.
Press and release the HomeLink® button you want to program
and check that the HomeLink® indicator light flashes orange.
Point the remote control
transmitter for the device at
the rear view mirror, 1 to 3 in.
(25 to 75 mm) from the
HomeLink
® buttons.
Keep the HomeLink® indicator
light in view while programming.
Program a device.
Programming a device other than an entry gate (for U.S.A.
owners)
Press and hold the remote control transmitter button until the
HomeLink
® indicator light changes from slowly flashing orange to
rapidly flashing gre en (rolling code) or continuously lit green
(fixed code), then release the button.
Programming an entry gate (for U.S.A. owners)/Programming
a device in the Canadian market
Press and release the remote con trol transmitter button at 2 sec-
ond intervals, repeatedly, until the HomeLink
® indicator light
changes from slowly flashing orange to rapidly flashing green
(rolling code) or continuous ly lit green (fixed code).
13
1
2
3

3715-4. Other interior features
5
Interior features
SEQUOIA_OM_USA_OM0C013U_19MY■
Certification for the garage door opener
For vehicles sold in the U.S.A.
FCC ID: NZLAECHL5
NOTE:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause har mful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
For vehicles sold in Canada
NOTE:
This device complies with Industry Canada licence-exempt RSS stan-
dard(s). Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any interfer-
ence, including interference that may cause undesired operation of the
device.
REMARQUE:
Le present appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisee aux
deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillag e radioelectrique
subi, meme si le brouillage est susceptible d’en compromettre le
fonctionnement.
■ When support is necessary
Visit on the web at www.homelink.com/toyota or call 1-800-355-3 515.
WARNING
■When programming a garage door or other remote control device
The garage door or other device may operate, so ensure people a nd
objects are out of danger to prevent potential harm.
■ Conforming to federal safety standards
Do not use the HomeLink
® compatible transceiver with any garage door
opener or device that lacks safety stop and reverse features as required by
federal safety standards. This includes any garage door that cannot detect
an interfering object. A door or device without these features increases the
risk of death or serious injury.
■ When operating or programming HomeLink
®
Never allow a child to operate or play with the HomeLink® buttons.