OTHER CONTROLS AND EQUIPMENT
Phone registration
To use the hands-free function with this unit, it is required to register the phone in advance.
NOTE: Up to 5 phones can be registered. To set up a new phone, disconnect the audio player from the unit. Connect the audio player again after phone setup is completed if necessary. When attempts to establish the pairing fail within 60 seconds, the connecting operation will be cance/ed. Try to establish the pairing again or refer to the manual of the phone in use for how to establish the pairing with the phone. 1) Press the Bluetooth® setup button (5)
or (6). The Bluetooth® setup menu will be dis
played. 2) Turn "TUNE/FLO PUSH SOUND" knob (1) to select "Setup Bluetooth", and press the knob (1) to determine the selection. 3) Turn "TUNE/FLO PUSH SOUND" knob (1) to select "Pairing", and press the knob (1) to determine the selection. 4) Select "CAR AUDIO" from the Bluetooth® menu of the phone and establish the pairing. Refer to the manual of the phone in use for further information. 5) Enter the passkey displayed on the unit to the phone.
5-63
6) When the pamng with the phone is established, automatic transfer of the phonebook and the call history becomes selectable. The automatic transfer starts with "Yes" and it does not with "No". 7) Press ON HOOK button (8).
NOTE: When selecting "Go Back" or pressing BACK button (4), the previous menu will be displayed. When registering an additional phone, repeat Step from 1).
Receiving a call Press OFF HOOK button (7) to receive a call.
Ending a call Press ON HOOK button (8) to end a call.
Rejecting a call (only for supported models) Press ON HOOK button (8) to reject a incoming call.
Mute of hands-free microphone Press MUTE switch (9) to mute the microphone. To cancel the mute, press MUTE switch (9) again.
Adjusting the listening volume Turn "VOL PUSH PWR" knob (2) during a call. Turning it clockwise increases the volume; turning it counterclockwise decreases the volume. Press "VOL" switch (10) during a call. Pressing the switch up increases the volume; pressing the switch down decreases the volume.
Adjusting the ring volume Turn "VOL PUSH PWR" knob (2) while a call is coming in. Turning it clockwise increases the volume; turning it counterclockwise decreases the volume. Press "VOL" switch (10) during a call. Pressing the switch up increases the volume; pressing the switch down decreases the volume.
No.Using Conditions • When temperature under -40-C . • On miring or sand ground . • On big gradient road . • In extreme nature condition: rainstorm, typhoon, cyclone, snowstorm, thunder•storm. etc . • Loading dangerous heavy, for instance: melted metal. acidity substance, radioactivity substance or specially crisp goods • • Contact with hood directly . • Using on boat. • The ground with difference in level.
Operation Instructions Whenever a wheel is changed, always remove any corrosion that may be present on inside of wheel and wheel mounting surface on vehicle. Details: Please operate according to the "operation instructions", Operate the jack on the level ground while checking the jack and the load. Musln"I operate under raising load, unless the load is fastened surely . • Park the car on the nat, love ground and apply the brake firmly. • Set transmission in "reverse"(automalic transmission in ·park") . • Turn on the hazard warning Hasher . • Remove jacklng tools and spare tire from stowage area . • Block fFont and rear of wheel diagonally opposlte wheel being removed before operating jack .
~
ITT
~ .s,.Cl(Jf>Of'(llITT J-'CKIW
~ • Loosen, but do not remove wheel nuts by turning wrench counter clockwise • • Raise jack until Jack-head groove fits boss or frame see Illustrations . • Operate jack with slow, smooth motion, using Jack handle . • Raise vehicle so an innated lire will just clear surface, remove nuts and wheel. • Install wheel, then slightly tighten each nut, wheel must be seated on hub . • lower vehicle, and fully tighten wheel nuts In across-cross sequence by turning wrench clockwise.
Maintenance • Please prevent the JACK SCREW from accretion of dirt . • Check the nameplate, keep the shape same as original. • No-re jigger the Jack's construction privately . • After any use, consult immediately your Suzuki Dealer or Service Partner for inspection and maintenance of the jack . • If the label (slicker) is damaged, pt ease consult your Suzuki Dealer or Service Partner.
