2019 SUBARU OUTBACK lights

2
Remote Keyless Entry
1 Lock/Arm
• Press to lock all doors and the rear
gate and activate the security alarm.
• If any of the doors or the rear gate
are not fully closed, five rapid chirps
will sound and the hazard lights will
flash to alert you that the doors or the
rear gate are not properly closed.
• To activate the vehicle finder function,
press three times (within five seconds).
If you are within 30 feet of the vehicle,
the horn will sound one time and the
hazard lights will flash three times.
2 Unlock/Disarm
• Press once to unlock the driver’s door.
• Press twice (within five seconds) to
unlock all doors.
• When the “Unlock/Disarm” button
is pressed, the dome and map lights
will illuminate if the dome light switch
is in the middle position.
3 Unlocking the Rear Gate
• Press the button to unlock the
rear gate.
4 Panic Alarm
• Press once and the horn will sound
and the hazard lights will flash.
• Press any button on the remote
to deactivate.
Keyless Access and
Push Button Start
(if equipped)
By simply carrying the access key in your pocket, you can
lock and unlock doors, open the rear gate and start your
car without having to take the key fob out of your pocket.
1
2
3
4
1
23
4
3645633_19b_Subaru_Outback_QG_081418.indd 28/14/18 1:50 PM

14
Controls
While the light switch is on, rotate the dial downward to dim the instrument panel illumination.
Rotate the dial upward to make the illumination brighter. When the dial is fully rotated upward
(dots aligned), the instrument panel illumination stays at full bright\
ness.
Light Controls
Push slightly up
for lane change
or fully up for
right turn signal.
Push slightly down
for lane change
or fully down for
left turn signal.
Push forward to change from low
beam to high beam. Pull the lever
back to center to return to low beam.

Turns on instrument panel
lights, tail lights, parking lights
and license plate lights.
Turns on headlights, instrument
panel illumination, parking lights,
tail lights and license plate lights.
Rotate to turn
on fog lights
(if equipped).
AUTO: The vehicle’s lights are
automatically on or off, depending
on the level of outside light.
3645633_19b_Subaru_Outback_QG_081418.indd 148/14/18 1:51 PM

15
Windshield Wipers
To turn on the wipers, press the wiper control lever down one level for intermittent,
two levels for low, or three levels for high speed. Return the lever to the “OFF” position
to stop the wipers. For a single wipe, move the lever up. To spray washer fluid, pull
and hold the lever toward you. Rotate the dial to adjust the intermittent wiper speed.
To operate the rear wiper, rotate the end of the knob upward to the
intermittent, continuous, or wash position. When the rear wiper is off,
rotate the knob downward to wash and wipe the rear window.
Daytime Running Lights
Daytime running lights are standard on your vehicle. Only the front daytime
running lights will be automatically turned on when the engine has started,
the parking brake is fully released and the light switch is in the “OFF”,
“AUTO” or “
” position. The brightness of the illumination of the high
beam headlights is reduced by the daytime running light system. You must
always switch on your headlights when it is dark outside by turning the light
switch to the “
” position or have the switch in the “AUTO” position.
1
2
3
INT.
LOW
HIGH OFF
Controls
3645633_19b_Subaru_Outback_QG_081418.indd 158/14/18 1:52 PM
Getting
Started Instrument
Panel Gauges
Personalize ControlsWhile
Operating Safety/In Case
of Emergency Additional
Information

22
Electronic Parking Brake
To apply, depress the brake pedal and pull up the
parking brake switch. The brake system warning light
on the instrument panel and the indicator light on the
parking brake switch will illuminate.
To release, make sure all doors are closed and your
seatbelt is fastened, then gently push the accelerator
pedal. Or, while the ignition switch is in the ON position
and the brake pedal is depressed in, push down the
parking brake switch.
X-MODE®
X-MODE® is the integrated control system of the engine,
AWD and Vehicle Dynamics Control system. Press the
X-MODE button to activate. Press it again to deactivate.
Please refer to your Owner’s Manual for operational
parameters and details about this feature.
While Operating
Paddle Shift Control Switches (if equipped)
• Temporary use: Even when the selector is in the
“D” (Drive) position, you can temporarily shift the
gear by pulling the “+” or “–” paddle shift control
switch. The transmission will automatically
switch back to Normal Mode.
• When the selector lever is in Manual Mode, shift to the next higher gear\
by pulling the “+”
paddle shift control switch on the steering wheel. Pull the “–” paddle shift cont\
rol switch
to shift into the next lower gear.
Manual Shifting Operation

Arrow-shaped lights in the center of the instrument panel show whether an u\
pshift is possible
and whether a downshift is possible.
Hill Holder™ Function
To activate, press the Hill Holder switch. To deactivate, press the Hill Holder switch again.
When the Hill Holder function is activated, the parking brake will be au\
tomatically applied when
stopped on an uphill or downhill slope with the brake pedal pushed down.\
The brake system
warning light on the instrument panel and the indicator light on the parkin\
g brake
switch will illuminate.
3645633_19b_Subaru_Outback_QG_081418.indd 228/14/18 1:52 PM