2019 Ram 3500 technical specifications

TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9
10
11
1 INTRODUCTION ................................................................................................................................................................................. 132 GETTING TO KNOW YOUR VEHICLE ......................................................................................................................................... 16
3 GETTING TO KNOW YOUR INSTRUMENT PANEL .............................................................................................................. 160
4 SAFETY ................................................................................................................................................................................................. 195
5 STARTING AND OPERATING ...................................................................................................................................................... 290
6 IN CASE OF EMERGENCY .............................................................................................................................................................. 440
7 SERVICING AND MAINTENANCE ............................................................................................................................................. 499
8 TECHNICAL SPECIFICATIONS .................................................................................................................................................... 564
9 MULTIMEDIA .................................................................................................................................................................................... 575
10 CUSTOMER ASSISTANCE ............................................................................................................................................................. 673
11 INDEX .................................................................................................................................................................................................... 678

11
TECHNICAL SPECIFICATIONS
IDENTIFICATION DATA ............................................... 564
Vehicle Identification Number ................................. 564
 BRAKE SYSTEM ............................................................... 565
Hydraulic Brake Assist — 2500/3500 Models Only
(Except Power Wagon) ............................................... 565
 WHEEL AND TIRE TORQUE SPECIFICATIONS ..... 565
Torque Specifications ................................................ 565
 FUEL REQUIREMENTS .............................................. 567
6.4L Engine ................................................................... 567
Reformulated Gasoline .......................................... 568
Materials Added To Fuel .......................................... 568
Gasoline/Oxygenate Blends .................................... 568
Do Not Use E-85 In Non-Flex Fuel Vehicles............ 569
CNG And LP Fuel System Modifications ................ 569
MMT In Gasoline......................................................... 569
Fuel System Cautions.................................................. 570
Carbon Monoxide Warnings ................................... 570
 FLUID CAPACITIES .................................................... 571
 FLUIDS AND LUBRICANTS ......................................... 572
Engine ........................................................................... 572
Chassis ........................................................................ 574
MULTIMEDIA
UCONNECT SYSTEMS ................................................... 575
 DRAG & DROP MENU BAR .........................................575
 CYBERSECURITY ............................................................ 576
 UCONNECT SETTINGS .................................................578
Uconnect 3 Settings .....................................................578
Uconnect 4/4C/4C NAV Settings.............................597
Uconnect 4C NAV With 12–inch Display
Settings ..........................................................................621
 STEERING WHEEL AUDIO CONTROLS —
IF EQUIPPED ...................................................................642
Radio Operation........................................................... 642
Media Mode..................................................................642
 IPOD/USB/MP3 CONTROL — IF EQUIPPED ........643
 RADIO OPERATION AND MOBILE PHONES .........647
Regulatory And Safety Information .........................648

INTRODUCTION 15
WARNINGS AND CAUTIONS
This Owner’s Manual contains WARNINGS against oper-
ating procedures that could result in a collision, bodily injury
and/or death. It also contains CAUTIONS against proce -
dures that could result in damage to your vehicle. If you do
not read this entire Owner’s Manual, you may miss
important information. Observe all Warnings and Cautions.
VAN CONVERSIONS/CAMPERS
The New Vehicle Limited Warranty does not apply to body
modifications or special equipment installed by van conver -
sion/camper manufacturers/body builders. U.S. residents
refer to the Warranty Information book, Section 2.1.C. Cana -
dian residents refer to the “What Is Not Covered” section of
the Warranty Information book. Such equipment includes
video monitors, VCRs, heaters, stoves, refrigerators, etc. For
warranty coverage and service on these items, contact the
applicable manufacturer. Operating instructions for the special equipment installed by
the conversion/camper manufacturer should also be
supplied with your vehicle. If these instructions are missing,
please contact your authorized dealer for assistance in
obtaining replacement documents from the applicable
manufacturer.
For information on the Body Builder’s Guide refer to
www.rambodybuilder.com
. This website contains dimen -
sional and technical specifications for your vehicle. It is
intended for Second Stage Manufacturer's technical support.
For service issues, contact your authorized dealer.
VEHICLE MODIFICATIONS/ALTERATIONS
WARNING!
Any modifications or alterations to this vehicle could
seriously affect its roadworthiness and safety and may
lead to a collision resulting in serious injury or death.
1

STARTING AND OPERATING 297
ENGINE BLOCK HEATER — IF EQUIPPED
The engine block heater warms the engine, and permits
quicker starts in cold weather. Connect the cord to a stan-
dard 110-115 Volt AC electrical outlet with a grounded,
three-wire extension cord.
The engine block heater cord is routed through the grille by
the right front tow hook.
It includes a removable cap that is secured by a tethered
strap. It also has a c-clip that is used for storage when not in
use for the winter months. During winter months, remove
the heater cord wiring assembly from itself on the c-clip.
The engine block heater must be plugged in at least one hour
to have an adequate warming effect on the engine.
ENGINE BREAK-IN RECOMMENDATIONS
A long break-in period is not required for the engine and
drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After
the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or
90 km/h) are desirable.
While cruising, brief full-throttle acceleration within the
limits of local traffic laws contributes to a good break-in.
Wide-open throttle acceleration in low gear can be detri
-
mental and should be avoided.
The engine oil installed in the engine at the factory is a
high-quality energy conserving type lubricant. Oil changes
should be consistent with anticipated climate conditions
under which vehicle operations will occur. For the recom -
mended viscosity and quality grades, refer to “Fluids And
Lubricants” in “Technical Specifications”.

NOTE:
A new engine may consume some oil during its first few thou -
sand miles (kilometers) of operation. This should be considered
a normal part of the break-in and not interpreted as a problem.
Please check your oil level with the engine oil indicator often
during the break in period. Add oil as required.

WARNING!
Remember to disconnect the engine block heater cord
before driving. Damage to the 110-115 Volt electrical
cord could cause electrocution.
CAUTION!
Never use Non-Detergent Oil or Straight Mineral Oil in
the engine or damage may result.
5

482 IN CASE OF EMERGENCY
Dual Rear Wheel Jack Placement
6. Finish tightening the lug nuts. Push down on the lug wrench while at the end of the handle for increased
leverage. Tighten the lug nuts in a star pattern until each
nut has been tightened twice. For the correct lug nut
torque refer to “Torque Specifications” in “Technical
Specifications”. If in doubt about the correct tightness,
have them checked with a torque wrench by an autho -
rized dealer or service station. 7. Install the wheel center cap and remove the wheel blocks.
Do not install chrome or aluminum wheel center caps on
the spare wheel. This may result in cap damage.
8. Lower the jack to its fully closed position. Stow the replaced tire, jack, and tools as previously described.
NOTE:
The bottle jack will not lower by turning the dial (thumb -
wheel) by hand, it may be necessary to use the jack driver in
order to lower the jack
9. Adjust the tire pressure when possible.
NOTE:
Do not oil wheel studs. For chrome wheels, do not substitute
with chrome plated lug nuts.
WARNING!
A loose tire or jack thrown forward in a collision or hard
stop, could endanger the occupants of the vehicle.
Always stow the jack parts and the spare tire in the
places provided.

528 SERVICING AND MAINTENANCE
Automatic Transmission
Selection Of Lubricant
It is important to use the proper transmission fluid to ensure
optimum transmission performance and life. Use only the
manufacturer’s specified transmission fluid. Refer to “Fluids
And Lubricants” in “Technical Specifications”. It is
important to maintain the transmission fluid at the correct
level using the recommended fluid. No chemical flushes
should be used in any transmission; only the approved lubri-
cant should be used. Special Additives
The manufacturer strongly recommends against using any
special additives in the transmission. Automatic Transmis
-
sion Fluid (ATF) is an engineered product and its perfor -
mance may be impaired by supplemental additives.
Therefore, do not add any fluid additives to the transmis -
sion. Avoid using transmission sealers as they may
adversely affect seals.
• Overfilling the brake fluid reservoir can result in
spilling brake fluid on hot engine parts, causing the
brake fluid to catch fire. Brake fluid can also damage
painted and vinyl surfaces, care should be taken to
avoid its contact with these surfaces.
• Do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged,
causing partial or complete brake failure. This could
result in a collision.
WARNING! (Continued)CAUTION!
Using a transmission fluid other than the manufacturer’s
recommended fluid may cause deterioration in
transmission shift quality and/or torque converter
shudder. Refer to “Fluids, Lubricants, And Genuine
Parts” in this section for fluid specifications.
CAUTION!
Do not use chemical flushes in your transmission as the
chemicals can damage your transmission components.
Such damage is not covered by the New Vehicle Limited
Warranty.

SERVICING AND MAINTENANCE 529
Fluid Level Check — Eight-Speed Transmission
The fluid level is preset at the factory and does not require
adjustment under normal operating conditions. Routine
fluid level checks are not required, therefore the transmis-
sion has no dipstick. An authorized dealer can check your
transmission fluid level using special service tools.
If you notice fluid leakage or transmission malfunction, visit
an authorized dealer immediately to have the transmission
fluid level checked. Operating the vehicle with an improper
fluid level can cause severe transmission damage. Fluid And Filter Changes — Eight-Speed Transmission
Under normal operating conditions, the fluid installed at the
factory will provide satisfactory lubrication for the life of the
vehicle.
Routine fluid and filter changes are not required. However,
change the fluid and filter if the fluid becomes contaminated
(with water, etc.), or if the transmission is disassembled for
any reason.
Rear Axle And 4x4 Front Driving Axle Fluid Level
For normal service, periodic fluid level checks are not
required. When the vehicle is serviced for other reasons the
exterior surfaces of the axle assembly should be inspected. If
gear oil leakage is suspected inspect the fluid level. Refer to
“Fluids And Lubricants” in “Technical Specifications” for
further information. This inspection should be made with
the vehicle in a level position.
For all 2500/3500 Model axles, the fluid level should be 1/
4 in ± 1/4 in (6.4 mm ± 6.4 mm) below the fill hole on the
9.25 in front, 11.5 in rear axle, and 12.0 in rear axle.
CAUTION!
If a transmission fluid leak occurs, visit an authorized
dealer immediately. Severe transmission damage may
occur. An authorized dealer has the proper tools to adjust
the fluid level accurately.
7

530 SERVICING AND MAINTENANCE
Lubricant Selection
Refer to “Fluids And Lubricants” in “Technical Specifica-
tion” for further information.
NOTE:
The presence of water in the gear lubricant will result in
corrosion and possible failure of differential components.
Operation of the vehicle in water, as may be encountered in
some off-highway types of service, will require draining and
refilling the axle to avoid damage.
Limited-Slip Differentials DO REQUIRE limited slip oil
additive (friction modifiers).
NOTE:
Slight noise and mild shuddering may be evident while
turning a vehicle with limited slip differential on concrete or
dry pavement. These conditions should be considered
normal operation of the limited slip differential.
Drain And Refill
Refer to the “Maintenance Plan” for the proper maintenance
intervals.Transfer Case
Selection Of Lubricant
Use only the manufacturer's recommended fluid. Refer to
“Fluids And Lubricants” in “Technical Specifications” for
further information.
Fluid Level Check
This fluid level can be checked by removing the filler plug.
The fluid level should be to the bottom edge of the filler plug
hole with the vehicle in a level position.
Drain And Refill
Refer to the “Maintenance Plan” in this section for the proper
maintenance intervals.