2019 Ram 2500 traction control

STARTING AND OPERATING 313
NOTE:
The four-wheel drive system will not allow shifts between
2WD/4WD HIGH if the front and/or rear wheels are spin-
ning (no traction). In this situation, the selected position indi -
cator light will flash and the original position indicator light
will remain ON. At this time, reduce speed and stop spin -
ning the wheels to complete the shift.
2WD Or 4WD HIGH To 4WD LOW
NOTE:
When shifting into or out of 4WD LOW some gear noise may
be heard. This noise is normal and is not detrimental to the
vehicle or occupants.
Shifting can be performed with the vehicle rolling 2 to 3 mph
(3 to 5 km/h) or completely stopped. You can use either of
the following procedures:
Preferred Procedure
1. With the engine running, slow the vehicle to 2 to 3 mph (3 to 5 km/h).
2. Shift the transmission into NEUTRAL.
3. While still rolling, push the desired position on the transfer case control switch. 4. After the desired position indicator light is ON (not
flashing), shift the transmission back into gear.
Alternate Procedure
1. Bring the vehicle to a complete stop.
2. With the ignition switch in the ON position and the engine running, shift the transmission into NEUTRAL.
3. Push the desired position on the transfer case control switch.
4. After the desired position indicator light is ON (not flashing), shift the transmission back into gear.
NOTE:
• If Steps 1 or 2 of either the Preferred or Alternate Proce -
dure are not satisfied prior to attempting the shift, then the
desired position indicator light will flash continuously
while the original position indicator light is ON, until all
requirements have been met.
• The ignition switch must be in the ON position for a shift to take place and for the position indicator lights to be
operable. If the ignition switch is not in the ON position,
the shift will not take place and no position indicator lights
will be on or flashing.
5

STARTING AND OPERATING 321
(Continued)
during low-speed, extreme off-road situations where one
wheel is likely to not be in contact with the ground. It is not
recommended to drive the vehicle with the differentials
locked on pavement due to the reduced ability to turn and
speed limitations.Axle Lock Selector The locking axles are controlled by the axle locker switch.
The switch has three positions:
• AXLE UNLOCK – the front and rear axles are unlocked
• REAR LOCK – the rear axle is locked
• FRONT/REAR LOCK – the front and rear axles are locked
Under normal driving conditions, the switch should be left
in the AXLE UNLOCK position.
NOTE:
Even when the axles are in the AXLE UNLOCK position, the
limited slip differential in the rear axle still provides torque
biasing capability for moderate low traction environments.
During the command to lock the axle, the indicator light will
flash until the axle is locked. After the lock command has
been successfully executed, the light will remain on solid.
CAUTION!
• Do not lock the front or rear axle on hard surfaced roads. The ability to steer the vehicle is reduced and
damage to the drivetrain may occur when the axles are
locked on hard surfaced roads.
• Do not try to lock the rear axle if the vehicle is stuck andthe tires are spinning. You can damage drivetrain
components. Lock the rear axle before attempting situ -
ations or navigating terrain, which could possibly
cause the vehicle to become stuck. CAUTION!
(Continued)
5

STARTING AND OPERATING 325
Water Fording Characteristics
Water fording characteristic is the vehicle's ability to cross a
body of still water, where the powertrain and drivetrain are
safe from water ingestion. This vehicle has high water
fording characteristics with the ability to cross a pool of
water, without stopping, 24 inches (60 cm) deep at a
maximum speed of 10 mph (16 km/h) and a pool of water
30 inches (76 cm) deep at a maximum speed of 5 mph (8 km/
h), both with an entrance ramp angle of 1.3 degrees.
Simultaneous Brake And Throttle Operation
Many off-road driving conditions require the simultaneous
use of the brake and throttle (two footed driving). When
climbing rocks, logs, or other stepped objects, using light
brake pressure with light throttle will keep the vehicle from
jerking or lurching. This technique is also used when you
need to stop and restart a vehicle on a steep incline.The Basics Of Off-Road Driving
You will encounter many types of terrain driving off-road.
You should be familiar with the terrain and area before
proceeding. There are many types of surface conditions:
hard packed dirt, gravel, rocks, grass, sand, mud, snow and
ice. Every surface has a different effect on your vehicle's
steering, handling and traction. Controlling your vehicle is
one of the keys to successful off-road driving, so always keep
a firm grip on the steering wheel and maintain a good
driving posture. Avoid sudden accelerations, turns or
braking. In most cases there are no road signs, posted speed
limits or signal lights. Therefore you will need to use your
own good judgment on what is safe and what isn't. When on
a trail you should always be looking ahead for surface obsta
-
cles and changes in terrain. The key is to plan your future
driving route while remembering what you are currently
driving over.
CAUTION!
The door sill height is 25 inches (63.5 cm). Water may
intrude into the interior of the vehicle at greater depths.
WARNING!
Always wear your seat belt and firmly tie down cargo.
Unsecured cargo can become projectiles in an off-road
situation.
5

326 STARTING AND OPERATING
When To Use Low Range
When driving off-road, shift into 4LO (Low Range) for addi-
tional traction or to improve handling and control on slip -
pery or difficult terrain. Due to the lower gearing, low range
will allow the engine to operate in a higher power range.
This will allow you to idle over obstacles and down hills,
with improved control and less effort. Also, use 4LO (Low
Range) in rain, ice, snow, mud, sand, to get heavy loads
rolling, improve traction, or whenever 4HI (High Range)
traction will not do the job.
Driving In Snow, Mud And Sand
There is a drastic reduction in traction when driving in snow,
mud or sand. The vehicle will be less responsive to steering,
acceleration and braking inputs. Therefore you should accel -
erate slowly, leave greater stopping distances and avoid
abrupt vehicle maneuvers. You want to keep a slow constant
steady pace. The key is to maintain the vehicle's momentum. •
Snow – In heavy snow or for additional control and trac -
tion at slower speeds, shift the transmission to a low gear
and shift the transfer case to 4LO (Low Range) if necessary.
Do not shift to a lower gear than necessary to maintain
headway. Over-revving the engine can spin the wheels
and traction will be lost. If you start to slow to a stop, try
turning your steering wheel no more than a ¼ turn quickly
back and forth, while still applying throttle. This will allow
the tires to get a fresh "bite" and help maintain your
momentum.
• Mud – Deep mud creates a great deal of suction around
the tires and is very difficult to get through. You should
use 4LO (Low Range) with a gear low enough to maintain
your momentum without shifting. If you start to slow to a
stop, try turning your steering wheel no more than a ¼
turn quickly back and forth for additional traction. Mud
holes pose an increased threat of vehicle damage and
getting stuck. They are normally full of debris from
previous vehicles getting stuck. As a good practice before
CAUTION!
Never park your vehicle over dry grass or other
combustible materials. The heat from your vehicle
exhaust system could cause a fire.
CAUTION!
On icy or slippery roads, do not downshift at high
engine RPMs or vehicle speeds because engine braking
may cause skidding and loss of control.

STARTING AND OPERATING 327
entering any mud hole, get out and determine how deep it
is, if there are any hidden obstacles and if the vehicle can
be safely recovered if stuck.
• Sand – Soft sand is very difficult to travel through with full
tire pressure. When crossing soft sandy spots in a trail
maintain your vehicle's momentum and do not stop. The
key to driving in soft sand using the appropriate tire pres -
sure, accelerating slowly, avoiding abrupt maneuvers and
maintaining the vehicle's momentum. If you are going to
be driving on large soft sandy areas or dunes, reduce your
tire pressure to a minimum of 15 psi (103 kPa) to allow for
a greater tire surface area. Reduced tire pressure will dras -
tically improve your traction and handling, while driving
on the soft sand, but you must return the tires to normal air
pressure before driving on pavement or other hard
surfaces. Be sure you have a way to air the tires back up
prior to reducing the pressure.Crossing Obstacles (Rocks And Other High Points)

While driving off road, you will encounter many types of
terrain. These varying types of terrain bring different types of
obstacles. Before proceeding review the path ahead to deter -
mine the correct approach and your ability to safely recover the
vehicle if something goes wrong. Keeping a firm grip on the
steering wheel, bring the vehicle to a complete stop and then
inch the vehicle forward until it makes contact with the object.
Apply the throttle lightly while holding a light brake pressure
and ease the vehicle up and over the object.

Using A Spotter
There are many times where it is hard to see the obstacle or
determine the correct path. Determining the correct path can
be extremely difficult when you are confronting many obsta -
cles. In these cases have someone guide you over, through, or
around the obstacle. Have the person stand a safe distance in
front of you where they can see the obstacle, watch your tires
and undercarriage, and guide you through.
CAUTION!
Reduced tire pressures may cause tire unseating and
total loss of air pressure. To reduce the risk of tire
unseating, while at a reduced tire pressure, reduce your
speed and avoid sharp turns or abrupt maneuvers.
WARNING!
Crossing obstacles can cause abrupt steering system
loading which could cause you to loose control of your
vehicle.
5

STARTING AND OPERATING 329
Getting High Centered
If you get hung up or high centered on an object, get out of
the vehicle and try to determine what the vehicle is hung up
on, where it is contacting the underbody and what is the best
direction to recover the vehicle. Depending on what you are
in contact with, jack the vehicle up and place a few rocks
under the tires so the weight is off of the high point when
you let the vehicle down. You can also try rocking the vehicle
or winching the vehicle off the object.
Hill Climbing
Hill climbing requires good judgment and a good under-
standing of your abilities and your vehicle's limitations. Hills
can cause serious problems. Some are just too steep to climb
and should not be attempted. You should always feel confi -
dent with the vehicle and your abilities. You should always
climb hills straight up and down. Never attempt to climb a
hill on an angle. •
Before Climbing A Steep Hill – As you approach a hill
consider its grade or steepness. Determine if it is too steep.
Look to see what the traction is on the hill side trail. Is the
trail straight up and down? What is on top and the other
side? Are there ruts, rocks, branches or other obstacles on
the path? Can you safely recover the vehicle if something
goes wrong? If everything looks good and you feel confi -
dent, then change transmission into a lower gear, shift the
transfer case into 4LO (Low) and proceed with caution.
You should use first gear and 4LO (Low Range) for very
steep hills.
• Driving Up Hill – Once you have determined your ability
to proceed and have shifted into the appropriate gear, line
your vehicle up for the straightest possible run. Accelerate
with an easy constant throttle and apply more power as
you start up the hill. Do not race forward into a steep
grade, the abrupt change of grade could cause you to lose
control. If the front end begins to bounce, ease off the
throttle slightly to bring all four tires back on the ground.
As you approach the crest of the hill ease off the throttle
and slowly proceed over the top. If the wheels start to slip
as you approach the crest of a hill, ease off the accelerator
and maintain headway by turning the steering wheel no
more than a ¼ turn quickly back and forth. This will
provide a fresh "bite" into the surface and will usually
CAUTION!
Winching or rocking the vehicle off hard objects
increases the risk of underbody damage.
5

330 STARTING AND OPERATING
provide enough traction to complete the climb. If you do
not make it to the top, place the vehicle in REVERSE and
back straight down the grade using engine resistance
along with the vehicle brakes.
• Driving Down Hill – Before driving down a steep hill you
need to determine if it is too steep for a safe descent. What
is the surface traction? Is the grade too steep to maintain a
slow controlled descent? Are there obstacles? Is it a
straight descent? Is there plenty of distance at the base of
the hill to regain control if the vehicle descends too fast? If
you feel confident in your ability to proceed then make
sure you are in 4LO (Low Range) with the transmission in
first gear (manually select first gear on automatic transmis -
sions) and proceed with caution. Allow engine braking to
control the descent and apply your brakes if necessary, but
do not allow the tires to lock. •
Driving Across An Incline – If at all possible avoid
driving across an incline. If it is necessary, know your
vehicle's abilities. Driving across an incline places more
weight on the down hill wheels, which increases the possi -
bilities of a down hill slide or rollover. Make sure the
surface has good traction with firm and stable soils. If
possible transverse the incline at an angle heading slightly
up or down.
• If You Stall Or Begin To Lose Headway – If you stall or
begin to lose headway while climbing a steep hill, allow
your vehicle to come to a stop and immediately apply the
brake. Restart the engine and shift into REVERSE. Back
slowly down the hill allowing the compression braking of
the engine and transmission to help regulate your speed. If
WARNING!
Never attempt to climb a hill at an angle or turn around
on a steep grade. Driving across an incline increases the
risk of a roll over, which may result in severe injury or
death.
WARNING!
Do not descend a steep grade in NEUTRAL. Use vehicle
brakes in conjunction with engine braking. Descending
a grade too fast could cause you to lose control and be
seriously injured or killed.
WARNING!
Driving across an incline increases the risk of a rollover,
which may result in severe injury.

332 STARTING AND OPERATING
effectively increasing the water level on the vehicle. Be
sure to consider this when determining the depth and the
ability to safely cross.

• Crossing Puddles, Pools, Flooded Areas Or Other Standing
Water – Puddles, pools, flooded or other standing water areas
normally contain murky or muddy waters. These water types
normally contain hidden obstacles and make it difficult to
determine an accurate water depth, approach angle, and
bottom condition. Murky or muddy water holes are where
you want to hook up tow straps prior to entering. This makes
for a faster, cleaner and easier vehicle recovery. If you are able
to determine you can safely cross, than proceed using the low
and slow method.
• Crossing Ditches, Streams, Shallow Rivers Or Other
Flowing Water – Flowing water can be extremely dangerous.
Never attempt to cross a fast running stream or river even in
shallow water. Fast moving water can easily push your
vehicle downstream sweeping it out of control. Even in very
shallow water, a high current can still wash the dirt out from
around your tires putting you and your vehicle in jeopardy.
There is still a high risk of personal injury and vehicle damage with slower water currents in depths greater than the
vehicle's running ground clearance. You should never
attempt to cross flowing water which is deeper than the
vehicle's running ground clearance. Even the slowest current
can push the heaviest vehicle downstream out of control if the
water is deep enough to push on the large surface area of the
vehicle's body. Before you proceed determine the speed of the
current, the water's depth, approach angle, bottom condition
and if there are any obstacles, then cross at an angle heading
slightly upstream using the low and slow technique.

Airing Down For Off-Road Driving
Running lower tire pressure off-road can improve your ride
comfort and vehicle traction. Reducing the tire air pressure
allows the tire to bulge slightly, improving its surface area
for better flotation and ability to mold or form to the ground
contour. Different terrain, tires, and vehicles require
different tire pressure. Hard surfaces like rock and heavier
vehicles require higher pressures than softer surfaces such as
CAUTION!
Muddy waters can reduce the cooling system
effectiveness by depositing debris onto the radiator.
WARNING!
Never drive through fast moving deep water. It can push
your vehicle downstream, sweeping it out of control.
This could put you and your passengers at risk of injury
or drowning.