2019 Peugeot Rifter turn signal

23
Warning/indicator lampStateCause Actions/Observations
+
+ SCR emissions
control system
Fixed when the
ignition is switched
on, accompanied by
an audible signal and
a


message.A fault with the SCR emissions
control system has been
detected.
This alert disappears once the exhaust emissions
return to normal levels.
AdBlue
® warning
lamp flashing, on
switching on the
ignition, associated
with the fixed Ser vice
and engine diagnostic
warning lamps,
accompanied by an
audible signal and
a

message indicating
the remaining driving
range. Depending on the message
displayed, you can continue
driving for up to 685
miles
(1,100
km) before the engine
starting prevention system is
triggered. Carry out (3) as soon as possible to avoid running
out of fuel
.
AdBlue
® warning
lamp flashing, on
switching on the
ignition, associated
with the fixed Ser vice
and engine diagnostic
warning lamps,
accompanied by an
audible signal and
a


message. An engine immobiliser prevents
the engine from restarting (over
the authorised driving limit after
confirmation of a
fault with the
emissions control system). To restart the engine, carry out (2).
1
Instruments

30
- in zone B, the temperature of the engine
coolant is too high; the maximum
temperature and central STOP warning
lamps come on, accompanied by an audible
signal and a


warning message.
You must stop as soon as it is safe to do so.
Wait a
few minutes before switching off the
engine.
Contact a
PEUGEOT dealer or a qualified
workshop.
Checking
After driving for a few minutes, the temperature
a nd pressure in the cooling system increase.
To top up the level:
F

w
ait at least one hour for the engine to cool,
F

u
nscrew the cap by two turns to allow the
pressure to drop,
F

w
hen the pressure has dropped, remove the
cap,
F

t
op up the level to the "MA X" mark.
For more information on Checking levels ,
refer to the corresponding section.
Be aware of the risk of scalding when
topping up the coolant. Do not fill above
the maximum level (indicated on the
reservoir).
Engine oil level indicator
On versions fitted with an electric oil level
indicator, the state of the engine oil level is
displayed in the instrument panel for a few
seconds when the ignition is switched on, at
the same time as the ser vicing information.
The level read will only be correct if
the vehicle is on level ground and the
engine has been stopped for more than
30


minutes.
Oil level correct
This is indicated by a message in the
in strument panel.
Low oil level
If the low oil level is confirmed by a check using
t he dipstick, the level must be topped up to
avoid damage to the engine.
This is indicated by a

message in the
instrument panel.
Oil level indicator fault
Dipstick
To locate the dipstick and the oil filler
cap for the Diesel engine , refer to the
corresponding section.
A = maximum; never
exceed this level.
B = minimum; top up
the level via the oil filler
hole, with the oil type
that is suitable for your
engine.
This is indicated by a
message in the
instrument panel. Contact a PEUGEOT dealer
or a

qualified workshop.
Instruments

38
The unlocking, locking or deadlocking
does not take place:
-
i
f the ignition is on,
-

i
f one of the doors or the boot is still
open,
-

i
f the key for the
K
eyless Entry and
Starting system has been left inside
the vehicle.
When the vehicle is locked (with the
remote control or

K
eyless Entry and
Starting), if it is unlocked inadvertently,
it will lock itself again automatically after
about thirty seconds unless a
door has
been opened.
And if your vehicle has an alarm, this will
be reactivated (with interior volumetric
monitoring, even if this had been
deactivated).
The folding and unfolding of the door
mirrors by the remote control can be
deactivated by a
PEUGEOT dealer or
a


qualified workshop. As a
safety measure (with children on
board), never leave the vehicle without
taking your

K
eyless Entry and Starting
remote control with you, even for a
short
period.
Be aware of the risk of theft when the

K

eyless Entry and Starting remote control
is in the recognition zone with the vehicle
unlocked.
In order to preser ve the charge of the
battery in the remote control, the "hands-
free" functions go into extended stand-by
after 21
days without use.
To restore these functions, press one of
the remote control buttons or start the
engine with the remote control at the
reader.
Unlocking
With the key
F To completely unlock the vehicle, insert the
key in the lock then turn it towards the front
of the vehicle.
F

T
hen pull the handle to open the door.
If fitted to your vehicle, the alarm is not
deactivated. Opening a
door will trigger the
alarm, which can be stopped by switching the
ignition on.
With the remote control
F Press this button to unlock the vehicle.
If fitted to your vehicle, pressing
and holding this button opens
the windows. The window stops
when you release the control.
Unlocking is signalled by rapid flashing of
the direction indicators for a

few seconds.
Depending on version, the door mirrors
unfold and the alarm is deactivated.
Access

40
Locking
With the key
If your vehicle is not fitted with an alarm,
the locking/deadlocking is signalled by the
fixed illumination of the direction indicators
for about two seconds.
Depending on your version, the door
mirrors fold at the same time.
With the Keyless Entry and
Starting on your person
With side-hinged doors/tailgate
F To lock the vehicle, with the remote control
in the recognition zone A , press the left-
hand door/tailgate locking control.
F

T

o lock the vehicle, with the remote control
in the recognition zone A , press with
a

finger or thumb on the markings of one of
the front or rear door handles.
F

T

o lock the vehicle, insert the key in the lock
then turn it towards the rear of the vehicle.
With the remote control
F To lock the vehicle, press this button.
If fitted to your vehicle, pressing
and holding this button closes
the windows. The window stops
when you release the control.
Ensure that no person or object prevents
the correct closing of the windows.
Be particularly aware of children when
operating the windows.
If your vehicle is so equipped,
pressing and holding the locking
controls allows the windows to
be closed. If you release the
control, the window stops.
Driving with the doors locked could make
it more difficult for the emergency ser vices
to enter the vehicle in an emergency.
As a
safety measure (with children on
board), never leave the vehicle without
taking your remote control with you, even
for a
short period.
Access

41
If a door is not properly closed (except
t he right-hand door with side-hinged
d o o r s):
-

v
ehicle stationary and engine
running, this warning lamp comes
on, accompanied by an alert
message for a
few seconds,
-

v
ehicle moving (speed above
6
mph (10 km/h)), this warning
lamp comes on, accompanied
by an audible signal and an alert
message for a
few seconds.
Deadlocking
With the key
Deadlocking renders the exterior and
interior door controls inoperative.
It also deactivates the manual central
control button.
Therefore, never leave anyone inside the
vehicle when it is deadlocked.
F

T
o deadlock the vehicle, insert the key in the
lock then turn it towards the rear.
F

Then within five seconds , turn the key
towards the rear again.
With the remote control
F To deadlock the vehicle, press this button.
F
Then within five seconds after
locking , press this button again.
Depending on the version you have, the
electric door mirrors fold at the same time.
If your vehicle is so equipped,
pressing and holding the locking
controls allows the windows to
be closed. If you release the
button, the window stops.
With the Keyless Entry and
Starting on your person
F To lock the vehicle, with the remote control in the recognition zone A , press with
a
finger or thumb on the markings of one of
the front or rear door handles.
F

T
o deadlock the vehicle, press the marking
again within five seconds.
With side-hinged doors/tailgate
F To lock the vehicle, with the remote control in recognition zone A , press the left-hand
door/tailgate locking control.
F

T
o deadlock the vehicle, press the control
again within five seconds .
2
Access

42
Locating your vehicle
This function allows you to identify your vehicle
from a distance, particularly in poor light. Your
vehicle must have been locked for more than
five seconds.
Remote operation of lighting
A short press on this button allows
you to switch on the lighting from
a
distance (lighting the sidelamps,
dipped beam headlamps and number
plate lamps).
A second press on this button before
the end of the timed period cancels
the remote lighting.
Anti-theft protection
Electronic immobiliser
The remote control contains an electronic chip
which has a special code. When the ignition is
switched on, this code must be recognised in
order for starting to be possible. In the event of a
fault, you are
informed by illumination of this
warning lamp, an audible signal and
a message in the screen.
F
P
ress this button.
This will switch on the courtesy lamps and the
direction indicators will flash for around ten
seconds. The vehicle will not start; contact a PEUGEOT
dealer as soon as possible.
B a c k- u p c o nt r o l (s)
If the battery is flat, attempt to lock /unlock the
vehicle as usual. If this does not work, use the
mechanical systems described below.
Also use these systems to mechanically lock /
unlock the doors in the event of:
-

c
entral locking system failure,
-

r
emote control battery discharged,
-

r
emote control fault,
-

v
ehicle in an area subject to strong
electromagnetic interference.
Where is the integral key
of the
K
eyless Entry and
Starting?
Locking of the vehicle
F Insert the integral key in the driver's door
lock, then turn it to the rear.
Unlocking of the vehicle
F Insert the integral key in the driver's door lock, then turn it to the front.
F

P
ull and hold button 1
, to extract the integral
key 2 .
A few seconds after switching off the ignition,
this system locks the engine control system,
therefore preventing the engine from being
started in the event of a

break-in.
Access

83
F Turn the ring to another position.
Deactivation of the function is accompanied
by the display of a
message.
Operating fault
In the event of a fault with the
sunshine sensor, the lamps come on
and this warning lamp lights up in the
instrument panel, accompanied by an
audible signal and/or a message.
Contact a PEUGEOT dealer or a qualified
w orkshop.
In fog or snow, the sunshine sensor may
detect sufficient light. In this case, the
lighting will not come on automatically.
Do not cover the sunshine sensor, located
on the dashboard or at the top of the
windscreen behind the rear view mirror
(depending on equipment); the associated
functions would no longer be controlled.
Daytime running lamps/
sidelamps
The front lamps light up automatically when the
engine starts.
They provide the following functions:
-

D
aytime running lamps (lighting control
stalk at " AUTO" position with adequate light
level).
-

S
idelamps (lighting control stalk at " AUTO"
position with low light level or "Sidelamps
only" or "Dipped/main beam headlamps").
The LEDs are brighter when operating as
daytime running lamps.
Parking lamps
Automatic illumination of
headlamps
When a low level of ambient light is detected
b y a sunshine sensor, the number plate lamps,
sidelamps and dipped beam headlamps are
switched on automatically, without any action
on the part of the driver. They may also come
on if rain is detected, at the same time as
automatic operation of the windscreen wipers.
As soon as the brightness returns to
a
sufficient level or after the windscreen wipers
are switched off, the lamps are switched off
automatically.
F

T
urn the ring to the " AUTO" position.
Activation of the function is accompanied by
the display of a
message. Vehicle side marking by illumination of the
sidelamps on the traffic side only.
F

D
epending on version, within one minute
of switching off the ignition, operate the
lighting control stalk up or down, depending
on the traffic side (for example, when
parking on the right, push the lighting
control stalk downwards; the left-hand
sidelamps come on).
This is confirmed by an audible signal and
illumination of the corresponding direction
indicator lamp in the instrument panel.
To switch off the parking lamps, return the
lighting control stalk to the central position.
4
Lighting and visibility

94
Electronic stability control
(ESC)
Electronic stability control programme
incorporating the following systems:
-
A
nti-lock braking system (ABS) and
Electronic brake force distribution (EBFD).
-
E

mergency braking assistance (EBA).
-
A

nti-slip regulation (ASR).
-
D

ynamic stability control (DSC).
-
A

utomatic post-collision braking (APCB).
-

T
railer stability assist (TSA).
Definitions
Anti-lock braking system (ABS)
and electronic brake force
distribution (EBFD)
These systems improve the stability and
manoeuvrability of your vehicle when braking
and contribute towards improved control in
corners, in particular on poor or slippery road
surfaces.
The ABS prevents wheel lock in the event of
emergency braking.
The EBFD system manages the braking
pressure wheel by wheel.
Emergency braking assistance
(EBA)
In an emergency, this system enables you to
reach the optimum braking pressure more
quickly and therefore reduce the stopping
distance.
It is triggered in relation to the speed at which
the brake pedal is pressed. This is felt by
a reduction in the resistance of the pedal and
an increase in braking efficiency.
Anti-slip regulation (ASR)
This system optimises traction in order to
avoid wheel slip by acting on the brakes of
the driving wheels and on the engine. It also
improves the directional stability of the vehicle
on acceleration.
Dynamic stability control (DSC)
If there is a difference between the path
f ollowed by the vehicle and that required by the
driver, this system monitors each wheel and
automatically acts on the brake of one or more
wheels and on the engine to return the vehicle
to the required path, within the limits of the laws
of physics.
Trailer stability assist (TSA)
This system allows control of the vehicle to be
retained when towing a trailer, so as to avoid
the risk of snaking.
Anti-lock braking system
(ABS) and electronic brake
force distribution (EBFD)
The fixed illumination of this warning
lamp signals that there is a fault with
the ABS.
Illumination of this warning lamp,
coupled with the STOP and ABS
warning lamps, accompanied by
the display of a
message and an
audible signal, signals that there is
a
fault with the electronic brake force
distribution (EBFD).
The vehicle retains conventional braking. Drive
carefully at moderate speed.
Contact a
PEUGEOT dealer or a qualified
workshop as soon as possible.
You must stop as soon as it is safe to do so.
Call a

PEUGEOT dealer or a qualified
workshop.
Safety