2019 Peugeot 208 lock

61
Anti-lock braking system
(ABS) and electronic brake
force distribution (EBFD)
The fixed illumination of this warning
lamp indicates that there is a fault
with the ABS.
The vehicle retains conventional braking. Drive
carefully at moderate speed. If these warning lamps come on,
accompanied by an audible signal
and a
message, this indicates a fault
with the electronic brake force
distribution (EBFD) system.
When changing wheels (tyres and rims),
ensure that these are approved for your
vehicle.
Normal operation of the ABS may make
itself felt by slight vibration of the brake
pedal. If you need to brake in an emergency,
press the brake pedal ver y firmly and
keep the pressure applied.
You must stop as soon as it is safe to do so.
In both cases, have the system checked by
a

PEUGEOT dealer or a qualified workshop as
soon as possible.Anti-slip regulation (ASR)/
Dynamic stability control
(DSC)
Operation
These systems are activated automatically
every time the vehicle is started.
They come into operation in the event of
a
problem with grip or trajectory. This is indicated by flashing of this
warning lamp in the instrument panel.
Deactivation
In exceptional conditions (starting a vehicle
w hich is bogged down, stuck in snow, on soft
ground, etc.), it may be advisable to deactivate
these systems, so that the wheels can turn
freely and regain grip.
Reactivate these systems as soon as the level
of grip permits.
Deactivation of ASR and DSC using the button
F Press this button.
The orange indicator lamp in the button comes
on.
The ASR and DSC systems will no longer have
an effect on engine operation or the brakes in
the event of an involuntary change of trajectory.
Deactivation of ASR using the touch screen
The deactivation is configured in the
Driving/Vehicle menu.
It is confirmed by the display of a
message.
Reactivation
These systems are reactivated automatically
each time the ignition is switched back on or
above 31 mph (50 km/h).
Below 31
mph (50 km/h), you can reactivate
them manually.
5
Safety

64
Advice
The driver must ensure that passengers
use the seat belts correctly and that they
are all fastened before setting off.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for
short journeys.
Do not interchange the seat belt buckles
as they will not fulfil their role fully.
The seat belts are fitted with an inertia
reel permitting automatic adjustment of
the length of the strap to your size. The
seat belt is stowed automatically when not
in use.
The inertia reels have an automatic
locking device at the time of a collision,
during sudden braking or if the vehicle
turns over. You can release the device by
pulling the strap firmly and then releasing
it so that it reels in slightly.
Before and after use, ensure that the seat
belt is reeled in correctly.
After folding or moving a
seat or rear
bench seat, ensure that the seat belt is
positioned and reeled in correctly. Installation
The lower part of the strap must be
positioned as low as possible on the
pelvis.
The upper part must be positioned in the
hollow of the shoulder.
In order to be effective, a seat belt must:
-

b
e tightened as close to the body as
possible,
-

b
e pulled in front of you with a smooth
movement, checking that it does not
twist,
-

b
e used to restrain only one person,
-

n
ot show any signs of cuts or fraying,
-

n
ot be converted or modified to avoid
affecting its performance.
Recommendations for children
Use a
suitable child seat if the passenger
is less than 12
years old or shorter than
one and a
half metres.
Never use the same seat belt to secure
more than one child.
Never allow a
child to travel on your lap.
For more information on Child seats , refer
to the corresponding section. Maintenance
In accordance with current safety
regulations, for all repairs on your
vehicle's seat belts, go to a
qualified
workshop with the skills and equipment
needed, which a
PEUGEOT dealer is able
to provide.
Have your seat belts checked regularly
by a
PEUGEOT dealer or a qualified
workshop, particularly if the straps show
signs of damage.
Clean the seat belt straps with soapy
water or a
textile cleaning product, sold by
PEUGEOT dealers.
In the event of an impact
Depending on the nature and
seriousness of the impact , the
pyrotechnic pretensioner may be deployed
before and independently of the airbags.
Deployment of the pretensioners is
accompanied by a
slight discharge of
harmless smoke and a
noise, due to the
activation of the pyrotechnic cartridge
incorporated in the system.
In all cases, the airbag warning lamp
comes on.
Following an impact, have the seat
belts system checked and, if necessary,
replaced, by a
PEUGEOT dealer or
a


qualified workshop.
Safety

78
Advice
The incorrect installation of a child seat in
a vehicle compromises the protection of
the child in the event of an accident.
Ensure that there is no seat belt or seat
belt buckle under the child seat, as this
could destabilise it.
Remember to fasten the seat belts or
the child seat harness keeping the slack
relative to the child's body to a
minimum,
even for short journeys.
When installing a


child seat using the seat
belt, ensure that the seat belt is tightened
correctly on the child seat and that it
secures the child seat firmly on the seat
of your vehicle. If your passenger seat is
adjustable, move it forwards if necessary.
The head restraint must be removed
before installing a
child seat with
a
backrest on a passenger seat.
Ensure that the head restraint is stored or
attached securely to prevent it from being
thrown around the vehicle in the event
of sharp braking. Refit the head restraint
when the child seat is removed. Children at the rear
At rear seating positions, always leave
sufficient space between the front seat
and:
-

a "
rear ward facing" child seat,
-

t
he child's feet for a child seat fitted
"forward facing".
To do this, move the front seat for wards
and, if necessary, straighten its backrest.
For optimal installation of the "forward
facing" child seat, verify that its backrest is
as close as possible to the backrest of the
vehicle seat, if possible in contact with it.
Children at the front
The legislation on carrying children on the
front passenger seat is specific to each
country. Refer to the legislation in force in
the country in which you are driving.
Deactivate the front passenger airbag
when a "rear ward facing" child seat is
installed on the front passenger seat.
Other wise, there is a
risk of serious or
fatal injury to the child if the airbag is
deployed. Installing a


booster seat
The chest part of the seat belt must be
positioned on the child's shoulder without
touching the neck.
Ensure that the lap part of the seat belt
passes correctly over the child's thighs.
We recommend using a
booster seat with
a
backrest, equipped with a belt guide at
shoulder level.
Additional protections
To prevent accidental opening of the doors
and rear windows, use the child lock.
Take care not to open the rear windows by
more than one third.
To protect young children from the rays
of the sun, fit side blinds on the rear
windows.
As a
safety precaution, do not leave:
-

a c
hild or children alone and
unattended in a
vehicle,
-

a c
hild or an animal in a vehicle
which is exposed to the sun, with the
windows closed,
-

t
he keys within reach of children inside
the vehicle.
Safety

79
Child lock
Manual child lock
Mechanical system to prevent opening of a rear
d oor using its interior control.
The control is located on the edge of each rear
d o o r.
Locking
F Using the ignition key, turn the red control as far as it will go:
-

t
o the left on the left-hand rear door,
-

t
o the right on the right-hand rear door.
Unlocking
F Using the ignition key, turn the red control as far as it will go:
-

t
o the right on the left-hand rear door,
-

t
o the left on the right-hand rear door.
Electric child lock
Electric system for locking the rear doors so
that they cannot be opened using their interior
controls.
Activation
F With the ignition on, press this button.
The red indicator lamp in the button comes on,
accompanied by a message confirming the
activation.
This red indicator lamp remains on for as long
as the child lock is activated.
Opening the doors from the outside and
operation of the electric rear windows from the
driver's controls remain possible.
Deactivation
F With the ignition on, press this button again.
The indicator lamp in the button goes off,
accompanied by a
message to confirm
deactivation.
This indicator lamp remains off while the child
lock is switched off. Any other state of the indicator lamp
indicates a

f
ault with the electric child lock.
Have it checked by a PEUGEOT dealer or
a

qualified workshop.
This system is independent and in no
circumstances does it take the place of
the central locking control.
Check the status of the child lock each
time you switch on the ignition.
Always remove the key from the ignition
when leaving the vehicle, even for a short
time.
5
Safety

82
F Insert the key into the ignition switch.
The system recognises the starting code.
F Unlock the steering column by simultaneously turning the steering wheel and the key.
In some cases, you may have to apply
some force to turn the steering wheel (if
the wheels are on full lock against a
kerb,
for example).
F

T
urn the key all the way towards the
dashboard to position 3


(Starting).
F

W
hen the engine starts, release the key.
With Petrol engines , after a
cold start,
preheating the catalytic converter can
cause clearly-felt engine vibrations when
stationary, with the engine running, for
anything up to 2
minutes (accelerated idle
speed).
Electronic immobiliser
The original key contains a coded electronic
c hip. When the ignition is switched on, starting
is only possible if the code is detected and
recognised.
This anti-theft protection locks the engine
management system a
few moments after the
ignition is switched off and prevents starting of
the engine following a


break-in.
In the event of a
fault, you are
informed by the illumination of this
warning lamp, the emission of an
audible signal and the display of
a


message.
In this case, your vehicle will not start; contact
a
PEUGEOT dealer as soon as possible.
Switching off
F Immobilise the vehicle.
F T urn the key fully towards you to position
1


(Stop) .
F

R
emove the key from the ignition switch.
F

T
o lock the steering column, turn the
steering until it locks.
Free-wheeling
For safety reasons, do not free-wheel.
Other wise, some vehicle functions will no
longer be active. To facilitate unlocking of the steering
column, the front wheels should be
straight before switching off the engine.
Switching off the engine leads to a
loss of
braking assistance.
Key left in
If the key has been left in the ignition
switch at position 2

(Ignition on)
, the
ignition will be switched off automatically
after one hour.
To switch the ignition back on, turn the key
to position 1

(Stop)
, then back to position
2

(Ignition on)
.Parking brake
Releasing
Driving

100
Reversing camera
The reversing camera is activated automatically
when reverse gear is engaged.
The image is displayed on the touch screen.
The reversing camera function may be
supplemented with parking sensors.
The superimposed representation of guide
lines helps with the manoeuvre.
They are represented as lines marked "on the
ground" and do not indicate the position of the
vehicle in relation to tall obstacles (e.g. other
vehicles).
Some distortion of the image is normal.
The blue lines 1 represent the general direction of
t he vehicle (the distance between them represents
the width of your vehicle without the door mirrors).
The red line 2
represents a distance of about
30
cm beyond the edge of your vehicle's rear
b u m p e r.
The green lines 3
represent distances of about
1
and 2 metres beyond the edge of your vehicle's
rear bumper.
The reversing camera cannot, in any circumstances,
replace the need for vigilance on the part of the driver.
High-pressure jet wash
When washing your vehicle, do not direct
the lance from less than 30
cm from the
lens of the camera.
Opening the tailgate causes the display to
disappear.
Clean the reversing camera regularly
using a
soft, dry cloth.
Park Assist
The system detects a parking space and then
p rovides assistance with the parallel parking
manoeuvres.
The Park Assist system cannot in any
circumstances replace the need for vigilance on
the part of the driver.
The driver must remain in control of their vehicle
ensuring that the space remains clear during the
manoeuvre.
In some circumstances, the sensors may not
detect small obstacles located in their blind spots.
During manoeuvring phases, the steering
wheel per forms rapid turns: do not hold
the steering wheel, do not put your hands
between the spokes of the steering wheel.
Watch out for any object that could block
the manoeuvre (loose clothing, scar ves,
ties, etc.) – Risk of injury!
It controls the steering and provides visual and
audible information to the driver.
If you have a
manual gearbox, the driver
manages the acceleration, braking, gears and
clutch.
With an automatic gearbox, the driver manages
the acceleration, braking and gears.
The driver can take control at any time by
gripping the steering wheel.
Driving

107
Fuel tank
Tank capacity:
- around 50
litres (petrol).
-
around 50
litres (Diesel).
-
around 45


litres (BlueHDi Diesel).
With Stop & Start, never refuel with the
system in STOP mode; you must switch
off the ignition with the key.
Low fuel level
When the low fuel level is reached
in the fuel tank, this warning lamp
comes on in the instrument panel.
Approximately 5


litres of fuel
remain in the tank. When the
warning lamp flashes, ver y little
fuel remains in the tank.
Refuel as soon as possible to avoid running
out.
For more information on Running out of fuel
(Diesel) , refer to the corresponding section.
Refilling
A sticker on the inner face of the filler flap
reminds you of the type of fuel to use,
depending on your engine type. The key cannot be removed from the lock
until the filler cap is refitted.
Opening the filler cap may create a
noise
caused by an inrush of air. This vacuum is
entirely normal, resulting from the sealing
of the fuel system.
To refuel in complete safety:
F
Y
ou must switch off the engine
.
F
O
pen the fuel filler flap by pulling with
a finger at the cut-out 1
.
F I nsert the key in the filler cap, then turn it to
the left 2 . F

R
emove the filler cap and hook it onto the
clip located on the inside of the filler flap 3 .
F
F
ill up the tank completely, but do not
continue after the 3
rd cut- off of the
nozzle ; this could cause malfunctions.
Once you have finished refuelling:
F

R

efit the filler cap.
F

T

urn the key to the right, then remove it from
the filler cap.
F

C

lose the fuel filler flap.
If you have put in the wrong fuel for
your vehicle, you must have the fuel
tank drained and filled with the correct
fuel before star ting the engine.
Additions of fuel must be of at least 5

litres, in
order to be registered by the fuel gauge.
7
Practical information

119
In the event of an AdBlue® breakdown,
confirmed by the message "Add AdBlue:
Starting impossible", you must top up with
at least 5

litres.
Never pour AdBlue
® into the Diesel fuel
tank.
For the specifics associated with the
access configuration for the AdBlue
® tank
(via the boot or via the fuel filler flap), refer
to the descriptions given in detail further
on.
If any AdBlue
® is splashed, or if there are
any spillages on the side of the body, rinse
immediately with cold water or wipe with
a

damp cloth.
If the fluid has crystallised, clean it off
using a

sponge and hot water.
Important: when topping up after
a breakdown due to running out
of AdBlue, you must wait for at least
5
minutes before switching on the ignition
again, without opening the driver's
door, unlocking the vehicle or inser ting
the key in the switch.
Switch on the ignition, then after
a
minimum of 10 seconds, start the engine.
F Switch off the ignition and remove the key from the switch to switch off the engine.
Access through the boot
(1.6 BlueHDi Euro 6.1)
F Raise the boot carpet then, depending on
equipment, lift out the spare wheel and/or
the storage box.
F

W
ithout pressing, turn the black cap
a
quarter turn anti-clockwise and lift it off.
F

T
urn the blue cap 1/6 of a turn anti-
clockwise.
F

L
ift off the cap.
Access through the fuel filler flap
(1.5 BlueHDi Euro 6.2)
Refilling
F Obtain an AdBlue® container or bottle. After
first checking the use-by date, read the
instructions on the label carefully before
pouring the contents of the container or
bottle into your vehicle's AdBlue tank.
Or F

W

ith the vehicle unlocked and the fuel filler
flap open, turn the blue cap of the AdBlue
®
tank 1/6

of a

turn anti-clockwise.
F

R

elease the blue cap.
F

I

nsert the AdBlue
® pump nozzle and refill
the tank until the nozzle stops automatically.
7
Practical information