2019 Peugeot 208 key

88
With PureTech petrol and manual or
automatic gearbox:
-

A
s soon as the vehicle stops or the speed
is less than 2
mph (3 km/h) (with manual
gearbox and depending on version).
-

W
ith gear lever in neutral and clutch pedal
released (manual gearbox).
-

W
ith brake pedal pressed or gear lever in
position N (automatic gearbox).
Special cases: STOP mode not
available
STOP mode is not triggered when:
- t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-

t
he vehicle has not exceeded 6 mph
(10
km/h) since the last engine start using
t h e key,
-

t
he engine is needed to maintain
a


comfortable temperature in the passenger
compartment,
-

d
emisting is active,
-

s
ome temporary conditions (battery charge,
engine temperature, braking assistance,
exterior temperature, etc.) make this
necessary to ensure control of a
system.
This indicator lamp flashes for a
few
seconds, then goes off.
This operation is perfectly normal. A time counter calculates the
time spent in STOP mode during
a
journey. It is reset to zero every
time the ignition is switched on
using the key.
For your comfort, during parking
manoeuvres, STOP mode is not available
for a few seconds after coming out of
reverse gear.
The Stop & Start system does not affect
the functionalities of the vehicle, such as
braking.
With a
manual gearbox in STOP mode, if
a
gear is engaged without fully depressing
the clutch pedal, a message is displayed
asking you to depress the clutch pedal
again to restart the engine.
START mode
This indicator lamp goes off and the
engine restarts. With manual gearbox
:
-
W
ith clutch pedal depressed.
With automatic gearbox:
-
W
ith gear lever in position D or M
.
-
W
ith brake pedal released.
or
-
W
ith gear lever in position N.
-
W
ith brake pedal released.
-
T
hen gear lever in position D or M
.
or
-
W
ith reverse gear engaged.
Special cases: START mode
triggered automatically
As a safety measure and for your convenience,
S TART mode is triggered automatically when:
-
y

ou open the driver's door,
-
y

ou unfasten the driver's seat belt,
-

s
ome temporary conditions (battery charge,
engine temperature, braking assistance,
air conditioning setting, etc.) make this
necessary to ensure control of a
system or
the vehicle.
This indicator lamp flashes for a
few
seconds, then goes off.
This operation is perfectly normal.
Never refuel with the engine in STOP
mode; you must switch off the ignition
using the key.
Driving

89
Deactivation/Reactivation
In certain circumstances, such as the need
to maintain the temperature in the passenger
compartment, it may be useful to deactivate the
Stop & Start system.
The system can be deactivated at any time,
once the ignition is switched on.
If the engine is in STOP mode, it then restarts.
The Stop & Start system is reactivated
automatically every time the ignition is switched
on.Opening the bonnet Driving on flooded roads
Before driving through a
flooded road, it is
strongly recommended that you deactivate
the Stop & Start system.
For more information on Driving advice ,
particularly on flooded roads, refer to the
corresponding section.
Malfunction
The Stop & Start system requires a 12 V
b attery of specific technology and
specification.
All work on this type of battery must be
carried out only by a
PEUGEOT dealer or
a


qualified workshop.
For more information on the 12
V batter y,
refer to the corresponding section.
F

T

o deactivate or reactivate the system,
press this button.
The indicator lamp is lit when the system is
deactivated.
Before doing anything under the bonnet,
deactivate the Stop & Start system to avoid
the risk of injury related to an automatic
change to START mode.
Under-inflation detection
This system automatically monitors the tyre
pressure while driving.
The system monitors the pressure in all four
tyres, once the vehicle is moving.
It compares the information given by the
wheel speed sensors with reference values,
which must be reinitialised after ever y tyre
pressure adjustment or wheel change .
The system triggers an alert as soon as it
detects a
drop in the pressure of one or more
tyres.
In the event of a

fault with the system, the ECO
OFF switch warning lamp flashes, then comes
on fixed.
Have it checked by a

PEUGEOT dealer or
a


qualified workshop.
If a

fault occurs in STOP mode, the vehicle
may stall. All of the instrument panel warning
lamps come on. It is then necessary to switch
the ignition off and to restart the engine using
t h e key.
6
Driving

95
A short press decreases the setting by 1 mph
( km/h).
Pressing and holding decreases the setting in
steps of 5
mph (km/h).
Switching the function off
F Place the thumbwheel at the " 0" position:
cruise control mode is deselected. The
display returns to the total mileage recorder.
After switching off the ignition, all registered
speed settings are lost.
Malfunction
The registered speed is erased, then replaced
by three dashes.
Have it checked by a
PEUGEOT dealer or
a


qualified workshop. When changing the registered speed
setting by means of a
maintained press,
pay attention as the speed may increase
or decrease rapidly.
Do not use the cruise control on slippery
roads or in heavy traffic.
On a steep descent, the cruise control will
not be able to prevent the vehicle from
exceeding the registered speed.
The cruise control system cannot, in
any circumstances, replace the need
to obser ve speed limits or the need for
vigilance on the part of the driver.
To avoid any risk of jamming of the pedals:
-
e
nsure that the mat is positioned and
secured to the floor correctly,
-
n
ever fit one mat on top of another.
Memorising speeds
This function allows speed settings to be stored
that will then be offered for configuration of two
systems: speed limiter (limit speed) or cruise
control (cruise speed).
You can memorise up to five speed settings in
With touch screen
This memorisation can be
configured from the Driving/Vehicle

menu.
F

Sel

ect the " Driving functions " tab.
F

Sel

ect the " Adjusting speeds " function.
F

P

ress " ON" to activate the function.
F

T

ick the speed settings 1 to 5 that you want
to use.
F

S

elect the speed setting value that you want
to change.
F

E

nter the new value using the numerical
keypad and press " OK" to confirm.
As a

safety measure, the driver must carry
out these operations when stationary.
the system for each of the two systems.
By default, some speed settings are already
memorised.
6
Driving

107
Fuel tank
Tank capacity:
- around 50
litres (petrol).
-
around 50
litres (Diesel).
-
around 45


litres (BlueHDi Diesel).
With Stop & Start, never refuel with the
system in STOP mode; you must switch
off the ignition with the key.
Low fuel level
When the low fuel level is reached
in the fuel tank, this warning lamp
comes on in the instrument panel.
Approximately 5


litres of fuel
remain in the tank. When the
warning lamp flashes, ver y little
fuel remains in the tank.
Refuel as soon as possible to avoid running
out.
For more information on Running out of fuel
(Diesel) , refer to the corresponding section.
Refilling
A sticker on the inner face of the filler flap
reminds you of the type of fuel to use,
depending on your engine type. The key cannot be removed from the lock
until the filler cap is refitted.
Opening the filler cap may create a
noise
caused by an inrush of air. This vacuum is
entirely normal, resulting from the sealing
of the fuel system.
To refuel in complete safety:
F
Y
ou must switch off the engine
.
F
O
pen the fuel filler flap by pulling with
a finger at the cut-out 1
.
F I nsert the key in the filler cap, then turn it to
the left 2 . F

R
emove the filler cap and hook it onto the
clip located on the inside of the filler flap 3 .
F
F
ill up the tank completely, but do not
continue after the 3
rd cut- off of the
nozzle ; this could cause malfunctions.
Once you have finished refuelling:
F

R

efit the filler cap.
F

T

urn the key to the right, then remove it from
the filler cap.
F

C

lose the fuel filler flap.
If you have put in the wrong fuel for
your vehicle, you must have the fuel
tank drained and filled with the correct
fuel before star ting the engine.
Additions of fuel must be of at least 5

litres, in
order to be registered by the fuel gauge.
7
Practical information

119
In the event of an AdBlue® breakdown,
confirmed by the message "Add AdBlue:
Starting impossible", you must top up with
at least 5

litres.
Never pour AdBlue
® into the Diesel fuel
tank.
For the specifics associated with the
access configuration for the AdBlue
® tank
(via the boot or via the fuel filler flap), refer
to the descriptions given in detail further
on.
If any AdBlue
® is splashed, or if there are
any spillages on the side of the body, rinse
immediately with cold water or wipe with
a

damp cloth.
If the fluid has crystallised, clean it off
using a

sponge and hot water.
Important: when topping up after
a breakdown due to running out
of AdBlue, you must wait for at least
5
minutes before switching on the ignition
again, without opening the driver's
door, unlocking the vehicle or inser ting
the key in the switch.
Switch on the ignition, then after
a
minimum of 10 seconds, start the engine.
F Switch off the ignition and remove the key from the switch to switch off the engine.
Access through the boot
(1.6 BlueHDi Euro 6.1)
F Raise the boot carpet then, depending on
equipment, lift out the spare wheel and/or
the storage box.
F

W
ithout pressing, turn the black cap
a
quarter turn anti-clockwise and lift it off.
F

T
urn the blue cap 1/6 of a turn anti-
clockwise.
F

L
ift off the cap.
Access through the fuel filler flap
(1.5 BlueHDi Euro 6.2)
Refilling
F Obtain an AdBlue® container or bottle. After
first checking the use-by date, read the
instructions on the label carefully before
pouring the contents of the container or
bottle into your vehicle's AdBlue tank.
Or F

W

ith the vehicle unlocked and the fuel filler
flap open, turn the blue cap of the AdBlue
®
tank 1/6

of a

turn anti-clockwise.
F

R

elease the blue cap.
F

I

nsert the AdBlue
® pump nozzle and refill
the tank until the nozzle stops automatically.
7
Practical information

140
Quick-release terminal clamp
Disconnecting the (+) terminalReconnecting the (+) terminal
Do not force the lever as locking will not
be possible if the clamp is not positioned
correctly; start the procedure again.
Before disconnecting
Wait 2 minutes after switching off the ignition
b efore disconnecting the battery.
Close the windows and the doors before
disconnecting the battery.
Following reconnection
After each time that the battery has been
reconnected, switch on the ignition and wait
1
minute before starting the engine, to allow
the electronic systems to initialise. However,
if minor problems persist after this procedure,
contact a
PEUGEOT dealer or a qualified
workshop.
Referring to the corresponding section, you
must yourself reinitialise:
-

t
he remote control key,
-

t
he date and time,
-

t
he radio preset stations.
F

Ra

ise the lever A fully to release the
clamp B .
F

R

emove the clamp B by lifting it off. F

Ra

ise the lever A fully.
F

R

efit the open clamp B on the (+) terminal.
F

P

ush the clamp B fully down.
F

L

ower the lever A to lock the clamp B .
To w i n g
Procedure for having your vehicle towed or for
towing another vehicle using the towing eye.
F

s

witch off all electrical consumers (audio
system, wipers, lighting, etc.),
F

s

witch off the ignition and wait for 4

m

inutes.
At the battery, it is only necessary to
disconnect the (+) terminal.
In the event of a breakdown

141
General recommendations
Obser ve the legislation in force in the
country where you are driving.
Ensure that the weight of the towing
vehicle is higher than that of the towed
vehicle.
The driver must remain at the wheel of
the towed vehicle and must have a valid
driving licence.
When towing a
vehicle with all four wheels
on the ground, always use an approved
towbar; rope and straps are prohibited.
The towing vehicle must move off gently.
When the vehicle is towed with its engine
off, there is no longer braking and steering
assistance.
In the following cases, you must always
call on a
professional recovery ser vice:
-

v
ehicle broken down on a motor way or
fast road,
-
f

our-wheel drive vehicle,
-

w
hen it is not possible to put the
gearbox into neutral, unlock the
steering, or release the parking brake,
-

w
hen it is not possible to tow a vehicle
with an automatic gearbox, engine
running,
-

t
owing with only two wheels on the
ground,
-

w
here there is no approved towbar,
etc. available.Access to the tools
Towing your vehicle
The towing eye is installed in the boot under
t h e f l o o r.
To gain access:
F

o
pen the boot,
F

l
ift the floor and remove it,
F

r
emove the towing eye from the carrier box.
F

O
n the front bumper, unclip the cover by
pressing at bottom right.
F

S
crew the towing eye in fully.
F

I
nstall the towbar. F

P
lace the gearbox in neutral.
F

ailure to follow this instruction may
cause damage to some components
(braking, transmission, etc.) and the
absence of braking assistance when
the engine is restarted.
F
U
nlock the steering by turning the ignition
key one notch and release the parking
brake.
F S witch on the hazard warning lamps on
both vehicles.
F

M
ove off gently, drive slowly and for a short
distance.
Towing another vehicle
F On the rear bumper, unclip the cover by pressing at the bottom.
F

S
crew the towing eye in fully.
F

I
nstall the towbar.
F

S
witch on the hazard warning lamps on
both vehicles.
F

M
ove off gently, drive slowly and for a short
distance.
8
In the event of a breakdown

5
Select a line in the list.
C onfirm with " OK".
Return to the top level of the folder structure to
select the type of tracks.
-

By Folders (CD or USB): all folders
containing audio files recognised on the
peripheral device, in alphabetical order
without following the folder structure.
-

By Artist (USB only): all of the artist names
defined in the ID3


Tags, in alphabetical
o r d e r.
-

By Genre (USB only): all of the genres
defined in the ID3
Tags.
-

By Playlist (CD or USB): if playlists have
been saved.
Information and advice
The audio system will only play files with
".mp3", ".wma" and ".wav" extensions on a CD
and can play files with ".ogg" extension only on
USB.
File names should have less than
20


characters, avoiding special characters
(e.g. " ?; ù) so as to avoid any reading or
display problems. If the disc is burned in another format, it may
not be played correctly.
It is recommended that the same burning
standard is always used on an individual disc,
with the lowest speed possible (4x maximum)
for the best acoustic quality.
In the particular case of a
multi-session CD, the
Joliet standard is recommended.
The playlists accepted on CD, MP3, iPod and
USB connection are types ".m3u" and ".wpl".
The system can recognise up to 5,000 files in
500 folders on 8 levels.
On a single disc, the CD player can read up
to 255 MP3 files spread over 8 folder levels
with a maximum of 192 folders. However, it
is recommended that the number of levels is
limited to 2 so as to reduce the time taken to
access and play the CD.
The folder structure is not obser ved during
playback.
Do not connect a hard disk or USB device other
than audio players to the USB socket. This may
cause damage to your installation.
Use only USB memory sticks formatted to FAT
32
(File Allocation Table).To protect the system, do not use a
USB
hub.
Bluetooth® audio streaming
Streaming allows music files on a telephone to
b e heard via the vehicle's speakers.
Connect the telephone: see the " Telephone"
section.
In the " Bluetooth: Audio " menu, select the
telephone to be connected.
The audio system connects to a
newly paired
telephone automatically.
Activate the streaming source by
pressing the SRC/TEL button.
In certain cases, play of the audio
files must be initiated from the
keypad.
The control of common tracks is possible
via the audio system control buttons and the
steering mounted controls, if the telephone
supports the function.
Contextual information can be displayed in the
screen.
The audio quality depends on the quality of
transmission by the telephone. It is recommended that you use genuine
Apple
® USB cables for correct operation.
In order to be able to play a

burned CDR or
CDRW, select standards ISO

9660

level 1, 2

or
Joliet if possible when burning the CD.
.
Bluetooth® audio system