2019 Peugeot 208 steering

65
AirbagsImpact detection zones
A.Front impact zone.
B. Side impact zone.
The deployment of one or more airbags
is accompanied by a
slight emission of
smoke and a
noise, due to the detonation
of the pyrotechnic charge incorporated in
the system.
This smoke is not harmful, but sensitive
individuals may experience slight irritation.
The detonation noise associated with the
deployment of one or more airbags may
result in a
slight loss of hearing for a short
time.
General information
System designed to contribute towards
improving passenger safety (with the exception
of the rear centre passenger) in the event of
violent collisions. The airbags supplement the
action of the seat belts fitted with force limiters
(all except the centre rear passenger).
If a
collision occurs, the electronic detectors
record and analyse the front and side impacts
sustained in the impact detection zones:
-

i
n the case of a serious impact, the airbags
are deployed instantly and contribute
towards better protection of the occupants
of the vehicle (with the exception of the rear
centre passenger); immediately after the
impact, the airbags deflate rapidly so that
they do not hinder visibility or the exit of the
occupants,
-

i
n the case of a minor or rear impact or
in certain rollover conditions, the airbags
may not be deployed; the seat belt
alone contributes towards ensuring your
protection in these situations.
The airbags do not operate when the
ignition is switched off.
This equipment will only deploy once. If
a
second impact occurs (during the same
or a
subsequent accident), the airbag will
not be deployed again.
Front airbags
This system protects the driver and front
passenger in the event of a severe frontal
impact in order to limit the risk of injury to the
head and chest.
The driver's airbag is fitted in the centre of the
steering wheel; the front passenger's airbag is
fitted in the dashboard above the glove box.
Deployment
The airbags are deployed, except the front
passenger airbag if it is deactivated*, in the
event of a
serious front impact to all or part
of the front impact zone A , in the longitudinal
centreline of the vehicle on a
horizontal plane
and directed from the front to the rear of the
vehicle.
The front airbag inflates between the thorax
and head of the front occupant of the vehicle
and the steering wheel, driver's side, and the
dashboard, passenger's side, to cushion their
for ward movement.
*
F

or more information on Deactivating
the front passenger airbag , refer to the
corresponding section.
5
Safety

67
Advice
For the airbags to be fully effective,
observe the safety recommendations
below.
Adopt a normal and upright sitting
position.
Fasten your seat belt, ensuring it is
positioned correctly.
Do not leave anything between the
occupants and the airbags (a child, pet,
object, etc.), nor fix or attach anything
close to or in the way of the airbag release
trajectory; this could cause injuries during
their deployment.
Never modify the original definition of your
vehicle, particularly in the area directly
around the airbags.
After an accident or if the vehicle has
been stolen or broken into, have the
airbag systems checked.
All work on the airbag systems must be
carried out by a
PEUGEOT dealer or
a


qualified workshop.
Even if all of the precautions mentioned
are obser ved, a risk of injury or of minor
burns to the head, chest or arms when an
airbag is deployed cannot be ruled out.
The airbag inflates almost instantly (within
a
few milliseconds) then deflates within
the same time discharging the hot gas via
openings provided for this purpose. Front airbags
Do not drive holding the steering wheel
by its spokes or resting your hands on the
centre part of the wheel.
Passengers must not place their feet on
the dashboard.
Do not smoke as deployment of the
airbags can cause burns or the risk of
injury from a
cigarette or pipe.
Never remove or pierce the steering wheel
or hit it violently.
Do not fix or attach anything to the
steering wheel or dashboard, this could
cause injuries with deployment of the
airbags.
Curtain airbags
Do not fix or attach anything to the roof,
as this could cause head injuries when the
curtain airbag is deployed.
If fitted to your vehicle, do not remove the
grab handles installed on the roof, they
play a


part in securing the curtain airbags.Lateral airbags
Use only approved covers on the seats,
compatible with the deployment of the
lateral airbags. For information on the
product range of seat covers suitable for
your vehicle, contact a
PEUGEOT dealer.
Do not fix or attach anything to the seat
backrests (clothes, etc.) as this could
cause injuries to the thorax or arm when
the lateral airbag is deployed.
Do not sit with the upper part of the body
any nearer to the door than necessary.
The vehicle's front door panels include
side impact sensors.
A damaged door or any unauthorised or
incorrectly executed work (modification or
repair) on the front doors or their interior
trim could compromise the operation of
these sensors – risk of malfunction of the
lateral airbags!
Such work must only be done by
a
PEUGEOT dealer or a qualified
workshop.
5
Safety

82
F Insert the key into the ignition switch.
The system recognises the starting code.
F Unlock the steering column by simultaneously turning the steering wheel and the key.
In some cases, you may have to apply
some force to turn the steering wheel (if
the wheels are on full lock against a
kerb,
for example).
F

T
urn the key all the way towards the
dashboard to position 3


(Starting).
F

W
hen the engine starts, release the key.
With Petrol engines , after a
cold start,
preheating the catalytic converter can
cause clearly-felt engine vibrations when
stationary, with the engine running, for
anything up to 2
minutes (accelerated idle
speed).
Electronic immobiliser
The original key contains a coded electronic
c hip. When the ignition is switched on, starting
is only possible if the code is detected and
recognised.
This anti-theft protection locks the engine
management system a
few moments after the
ignition is switched off and prevents starting of
the engine following a


break-in.
In the event of a
fault, you are
informed by the illumination of this
warning lamp, the emission of an
audible signal and the display of
a


message.
In this case, your vehicle will not start; contact
a
PEUGEOT dealer as soon as possible.
Switching off
F Immobilise the vehicle.
F T urn the key fully towards you to position
1


(Stop) .
F

R
emove the key from the ignition switch.
F

T
o lock the steering column, turn the
steering until it locks.
Free-wheeling
For safety reasons, do not free-wheel.
Other wise, some vehicle functions will no
longer be active. To facilitate unlocking of the steering
column, the front wheels should be
straight before switching off the engine.
Switching off the engine leads to a
loss of
braking assistance.
Key left in
If the key has been left in the ignition
switch at position 2

(Ignition on)
, the
ignition will be switched off automatically
after one hour.
To switch the ignition back on, turn the key
to position 1

(Stop)
, then back to position
2

(Ignition on)
.Parking brake
Releasing
Driving

90
The tyre under-inflation detection system
does not replace the need for vigilance on
the part of the driver.
This system still requires you to check
the tyre inflation pressures (including
the spare wheel) every month as well as
before a

long journey.
Driving with under-inflated tyres impairs
handling, extends braking distances and
causes early tyre wear, particularly in
adverse conditions (heavy loads, high
speeds, long journeys).
Driving with under-inflated tyres
increases fuel consumption.
The tyre pressure specifications for your
vehicle can be found on the tyre pressure
label.
For more information on the
Identification markings , refer to the
corresponding section. Tyre pressures should be checked when
the tyres are "cold" (vehicle stopped for
1
hour or after a journey of less than
6
miles (10 km) at moderate speeds).
Other wise (when hot), add 0.3
bar to the
pressures shown on the label.
Under-inflation alert
This warning is indicated by fixed
illumination of this warning lamp, an
audible signal and, depending on
the equipment installed, a message
displayed on the screen.
F

R

educe speed immediately, avoid excessive
steering movements and sudden braking.
F

S

top the vehicle as soon as it is safe to do
so.
The loss of pressure detected does not
always cause visible bulging of the tyre.
Do not satisfy yourself with just a
visual
check. or
F

i
f it is not possible to carry out this check
immediately, drive carefully at reduced
speed.
The alert is kept active until the system is
reinitialised.
The under-inflation alert can only be relied
on if the reinitialisation of the system has
been done with the pressures in the four
tyres correctly adjusted.
Reinitialisation
The system must be reinitialised after any
adjustment to the pressure of one or more
tyres, and after changing one or more wheels.
Before reinitialising the system, ensure
that the pressures of the four tyres
are correct for the conditions of use
of the vehicle and conform to the
recommendations on the tyre pressure
label.
The under-inflation alert can only be relied
on if the reinitialisation of the system has
been done with the pressures in the four
tyres correctly adjusted.
The under-inflation detection system
does not give a
warning if a pressure is
incorrect at the time of reinitialisation.
F

I

n the event of a

puncture, use the
temporary puncture repair kit or the spare
wheel (depending on equipment),
or
F

i

f you have a

compressor, such as the one
in the temporary puncture repair kit, check
the pressures of the four tyres when cold,
Driving

91
Without touch screen
F With the ignition on and the vehicle stationary, press this button for about
3
seconds then release it, an audible signal
confirms the reinitialisation.
With touch screen
The reinitialisation of the system is done with
the ignition on and the vehicle stationary.
The reinitialisation of the system is
configured in the Driving/Vehicle
menu.
The new pressure parameters saved are
treated as reference values by the system.
Snow chains
The system does not have to be
reinitialised after fitting or removing snow
chains.
Malfunction
The flashing and then fixed illumination of the
under-inflation warning lamp, accompanied by
the illumination of the Ser vice warning lamp,
indicates a fault with the system.
In this case, under-inflation monitoring of the
tyres is no longer assured.
Have the system checked by a
PEUGEOT
dealer or a
qualified workshop.
After any inter vention on the system,
the pressures of the four tyres must be
checked and the system reinitialised.
Speed limiter "LIMIT"
The system prevents the vehicle from
exceeding the speed setting programmed by
the driver.
Steering mounted controls
1. Speed limiter mode selection/off.
2. Increases the set value.
3. Decreases the set value.
4. Speed limiter on/pause.
The speed setting is selected with the engine
running, stationary or when driving. The
minimum speed setting possible is 19
mph
(30


km/h).
The vehicle responds to the accelerator until
resistance is felt in the pedal, which signifies
that the vehicle has reached the limiter speed
setting.
However, pressing the pedal beyond this point
of resistance to the floor permits exceeding
of the programmed speed. To resume use
of the limiter, simply reduce the pressure on
the accelerator pedal gradually and return to
a


speed below that programmed.
Setting and operation of the system can be
done stationar y with the engine running or
when driving.
6
Driving

93
Malfunction
The registered speed is erased, then replaced
by three dashes.
Have it checked by a PEUGEOT dealer or
a


qualified workshop. Under no circumstances can the speed
limiter replace the need to obser ve speed
limits, nor the need for vigilance on the
part of the driver.
Always pay attention to the profile of the
road, be careful when accelerating sharply
and stay in complete control of your
vehicle.
To avoid any jamming under the pedals:
-

e
nsure that the mat is positioned and
secured to the floor correctly,
-

n
ever fit one mat on top of another.
Cruise control "CRUISE"
System which automatically maintains the
speed of the vehicle at the value programmed
by the driver, without any action on the
accelerator pedal.
Steering mounted controls
1.Cruise control mode selection/off.
2. Increase the programmed value.
3. Decrease the programmed value.
4. Stop/resume cruise control.
This driving assistance system, for use
when the traffic is flowing, allows a
speed
programmed by the driver to be maintained,
except on a
steep gradient.
With a
manual gearbox
In order for it to be programmed or activated,
the speed of the vehicle must be above 25
mph
(40
km/h) with 4
th gear or higher engaged.
With an automatic gearbox
In order for it to be programmed or activated,
the speed of the vehicle must be above 25
mph
Selection
(40 km/h) with 2nd gear or higher engaged in
manual mode, or position D selected.
F

P

lace the thumbwheel at the " CRUISE"
position: cruise control mode is selected,
but is not switched on (PAUSE).
Registering a cruise speed
se tting
- Bring the vehicle up to the desired speed by
pressing the accelerator.
-

P
ress the SET – or
SET + button.
The speed setting is registered/activated and
the vehicle will maintain this speed.
6
Driving

100
Reversing camera
The reversing camera is activated automatically
when reverse gear is engaged.
The image is displayed on the touch screen.
The reversing camera function may be
supplemented with parking sensors.
The superimposed representation of guide
lines helps with the manoeuvre.
They are represented as lines marked "on the
ground" and do not indicate the position of the
vehicle in relation to tall obstacles (e.g. other
vehicles).
Some distortion of the image is normal.
The blue lines 1 represent the general direction of
t he vehicle (the distance between them represents
the width of your vehicle without the door mirrors).
The red line 2
represents a distance of about
30
cm beyond the edge of your vehicle's rear
b u m p e r.
The green lines 3
represent distances of about
1
and 2 metres beyond the edge of your vehicle's
rear bumper.
The reversing camera cannot, in any circumstances,
replace the need for vigilance on the part of the driver.
High-pressure jet wash
When washing your vehicle, do not direct
the lance from less than 30
cm from the
lens of the camera.
Opening the tailgate causes the display to
disappear.
Clean the reversing camera regularly
using a
soft, dry cloth.
Park Assist
The system detects a parking space and then
p rovides assistance with the parallel parking
manoeuvres.
The Park Assist system cannot in any
circumstances replace the need for vigilance on
the part of the driver.
The driver must remain in control of their vehicle
ensuring that the space remains clear during the
manoeuvre.
In some circumstances, the sensors may not
detect small obstacles located in their blind spots.
During manoeuvring phases, the steering
wheel per forms rapid turns: do not hold
the steering wheel, do not put your hands
between the spokes of the steering wheel.
Watch out for any object that could block
the manoeuvre (loose clothing, scar ves,
ties, etc.) – Risk of injury!
It controls the steering and provides visual and
audible information to the driver.
If you have a
manual gearbox, the driver
manages the acceleration, braking, gears and
clutch.
With an automatic gearbox, the driver manages
the acceleration, braking and gears.
The driver can take control at any time by
gripping the steering wheel.
Driving

102
F Move your vehicle for ward until a new
message is displayed.
F

S
elect reverse and release the steering
wheel. The assisted parking manoeuvre is in progress.
Without exceeding 5
mph (8 km/h), continue
the manoeuvres following the information given
by the "Parking sensors" system, until the end
of manoeuvre message is displayed.
The indicator lamp in the control goes off,
accompanied by an audible signal.
The driver takes back control of the vehicle's
steering.
Exit from a parallel parking
sp ace
F When you want to exit from a parallel
parking space, start the engine.
With the vehicle stationary, to activate the Park
Assist system:
F

P
ress this control.
The indicator lamp in the control remains off.
A message is displayed in the screen.
F

S
elect the exit parking space manoeuvre.
The indicator lamp in the control comes on.
F

O
perate the direction indicator on the exit
from parking side.
T

he direction indicator flashes throughout
the manoeuvre, whatever the position of the
control stalk.
F

S
elect a for ward or reverse gear then
release the steering wheel.
Once measurement is complete, if the space is
large enough a


message indicates that parking
is possible.
Driving