2019 NISSAN ROGUE HYBRID battery location

HEV Overview
NISSAN PURE DRIVE® Hybrid System.......... HEV-2
Lithium-ion (Li-ion) battery ................... HEV-2
High-voltage cautions ........................ HEV-3
Road accident cautions ...................... HEV-3
Emergency shut-off system ..................HEV-4
Operation of the hybrid system ...............HEV-5
Starting and slow speed driving ...........HEV-5
Medium or high speed driving .............HEV-5
Rapid acceleration .........................HEV-5
Deceleration and braking ..................HEV-6
Stopping ..................................HEV-6
Energy monitors .............................HEV-6
Assist charge gauge .......................HEV-6 Energy Flow (models with Navigation
System)
................................... HEV-7
Fuel Economy .............................HEV-9
Energy/Fuel History (models with
Navigation System) ........................HEV-9
Regenerative brake .......................... HEV-10
Efficient use of your vehicle ...................HEV-11
Approaching Vehicle Sound for Pedestrians
(VSP) system .................................HEV-11
Hybrid vehicle precautions .................. HEV-12
High-voltage components and their
locations ................................. HEV-12
Hybrid vehicle characteristics ............. HEV-13

Drive your vehicle with smooth accelera-
tion and deceleration.∙ While driving, energy is recovered through the regenerative brake as the
vehicle decelerates. However, for most
efficient use, do not accelerate or decel-
erate your vehicle more than neces-
sary.
∙ Avoid abrupt acceleration and decel- eration.
∙ The power of the Li-ion battery can be checked on the Energy Flow in the cen-
ter display (models with Navigation Sys-
tem) or Li-ion battery status meter in
the vehicle information display. For ad-
ditional information, refer to “Energy
Flow (models with Navigation System)”
in this section or “Vehicle information
display” in the “Instruments and con-
trols” section of this manual. Gradual or
non-abrupt acceleration and decelera-
tion will make more effective use of the
electric power.
∙ When parking, be sure to place the shif t lever in the P (Park) position. While driv-
ing, place the shif t lever in the D (Drive)
position. The VSP system is a function that uses
sound to help alert pedestrians of the
presence of the vehicle when it is being
driven at a low speed in the electric drive
mode under the following conditions:
∙ The sound starts when the vehicle starts accelerating.
∙ The sound stops when the vehicle speed is more than 19 mph (30 km/h)
while accelerating only when the ve-
hicle is powered by the electric motor.
∙ The sound starts when the vehicle speed is less than 16 mph (25 km/h)
while decelerating only when the ve-
hicle is powered by the electric motor.
∙ The sound stops when the vehicle stops.
∙ The sound does not stop with the ve- hicle in the R (Reverse) position even if
the vehicle stops.
The VSP system is automatically turned on
when the vehicle is in the READY to drive
mode. If there is a malfunction in the VSP system,
the VSP OFF indicator light in the meter
illuminates. For additional information, re-
fer to “Approaching Vehicle Sound for Pe-
destrians (VSP) OFF indicator light” in the
“Instruments and controls” section of this
manual.
WARNING
∙ If the sound from the VSP system is
not heard while driving, stop the ve-
hicle in a safe and quiet location. Open
a window, and then place the vehicle
in the R (Reverse) position with the
brake pedal firmly depressed. Check
that the operating sound can be
heard from the front side of the
vehicle.
∙ If the sound cannot be heard, it is rec- ommended that you immediately
contact a NISSAN dealer for
inspection.
EFFICIENT USE OF YOUR VEHICLE APPROACHING VEHICLE SOUND FOR PEDESTRIANS (VSP) SYSTEM
HEV OverviewHEV-11

MR20DD engine
1. Engine coolant reservoir (P. 8-4)
2. Windshield-washer fluid reservoir(P. 8-12)
3. Inverter coolant reservoir (P. 8-6)
4. Engine oil dipstick (P. 8-7)
5. Engine oil filler cap (P. 8-7)
6. Brake fluid reservoir (P. 8-11)
7. Air cleaner (P. 8-15)
8. Fuse box (P. 8-20)
9. Radiator cap (P. 8-4)
Engine cover removed for clarity.
The 12–volt battery is located in the rear
cargo area of the vehicle.
Refer to the page number indicated in
parentheses for operating details.
LDI3135
ENGINE COMPARTMENT CHECK
LOCATIONS
0-8Illustrated table of contents

OPERATING RANGE
The Intelligent Key functions can only be
used when the Intelligent Key is within the
specified operating range from the request
switch
1.
When the Intelligent Key battery is dis-
charged or strong radio waves are present
near the operating location, the Intelligent
Key operating range becomes narrower,
and the Intelligent Key may not function
properly.
The operating range is within 31.5 in (80 cm)
from each request switch
1. If the Intelligent Key is too close to the door
glass, handle or rear bumper, the request
switches may not function.
When the Intelligent Key is within the oper-
ating range, it is possible for anyone, even
someone who does not carry the Intelli-
gent Key, to push the request switch to
lock/unlock the doors.
DOOR LOCKS/UNLOCKS
PRECAUTION
∙ Do not push the door handle request
switch with the Intelligent Key held in
your hand as illustrated. The close dis-
tance to the door handle will cause the
Intelligent Key system to have difficulty
recognizing that the Intelligent Key is
outside the vehicle.
∙ Af ter locking with the door handle re- quest switch, verif y the doors are se-
curely locked by testing them.
LPD2653LPD2554
Pre-driving checks and adjustments3-9

CAUTION
When the Intelligent Key battery is dis-
charged or other strong radio wave
sources are present near the operating
location, the Intelligent Key operating
range becomes narrower, and the Intel-
ligent Key may not function properly.
The Remote Hybrid Start function can only
be used when the Intelligent Key is within
the specified operating range from the ve-
hicle.
The Remote Hybrid Start operating range
is approximately 197 f t (60 m) from the ve-
hicle.
REMOTE STARTING THE VEHICLE
To use the Remote Hybrid Start feature to
start the hybrid system perform the follow-
ing: 1. Aim the Intelligent Key at the vehicle.
2. Press the
button to lock all
doors. 3. Within 5 seconds press and hold
the
button until the turn signal
lights flash and the tail lamps turn on. If
the vehicle is not within view press and
hold the
button for at least 2 sec-
onds.
The following events will occur when the
hybrid system starts:
∙ The parking lights will turn on and re- main on as long as the hybrid system is
running.
∙ The doors will be locked and the climate control system may come on.
∙ The hybrid system will continue to run for 10 minutes. Repeat the steps to ex-
tend the time for an additional 10 min-
utes. For additional information, refer to
“Extending hybrid system run time” in
this section.
Depress and hold the brake then push the
push-button ignition switch to the ON po-
sition before driving. For additional infor-
mation, refer to “Driving the vehicle” in the
“Starting and driving” section of this
manual.
EXTENDING HYBRID SYSTEM RUN
TIME
The Remote Hybrid Start feature can be
extended one time by performing the
steps listed in “Remote starting the vehicle”
in this section. Run time will be calculated
as follows: ∙ The first 10 minute run time will start when the Remote Hybrid Start function
is performed.
∙ The second 10 minutes will start imme- diately when the Remote Hybrid Start
function is performed again. For ex-
ample, if the hybrid system has been
running for 5 minutes, and 10 minutes
are added, the hybrid system will run for
a total of 15 minutes.
∙ Extending hybrid system run time will bring you to the two Remote Hybrid
Start limit.
A maximum of two Remote Hybrid Starts,
or a single start with an extension, are al-
lowed between ignition cycles. The ignition
switch must be cycled to the ON position
and then back to the OFF position before
the Remote Hybrid Start procedure can be
used again.
Pre-driving checks and adjustments3-21

OPERATING RANGE
The Intelligent Key functions can only be
used when the Intelligent Key is within the
specified operating range.
When the Intelligent Key battery is almost
discharged or strong radio waves are pres-
ent near the operating location, the Intelli-
gent Key system’s operating range be-
comes narrower and may not function
properly.If the Intelligent Key is within the operating
range, it is possible for anyone, even some-
one who does not carry the Intelligent Key,
to push the ignition switch to start the hy-
brid system.
The operating range of the hybrid system
start function is inside of the vehicle
1.
∙ The luggage area is not included in the operating range, but the Intelligent Key
may function.
∙ If the Intelligent Key is placed on the instrument panel or inside the glove
box, storage bin or door pocket, the In-
telligent Key may not function.
∙ If the Intelligent Key is placed near the door or window outside the vehicle, the
Intelligent Key may function.
PUSH-BUTTON IGNITION SWITCH
POSITIONS
LOCK (Normal parking position):
The ignition switch can only be locked in
this position.
The ignition switch will lock when any door
is opened or closed with the ignition
switched off. ON (Normal operating position):
This position turns on the ignition system
and electrical accessories.
ON has a battery saver feature that will
place the ignition switch in the OFF posi-
tion, if the vehicle is not running, af ter some
time under the following conditions:
∙ All doors are closed.
∙ The shif t lever is in P (Park).
The battery saver feature will be canceled if
any of the following occur: ∙ Any door is opened.
∙ The shif t lever is moved out of the P (Park) position.
∙ The ignition switch changes position.
CAUTION
Do not leave the vehicle with the igni-
tion switch in the ON position when the
engine is not running for an extended
period. This can discharge the battery.
LSD2020
Starting and driving5-15

Shif t lock release
If the battery charge is low or discharged,
the shif t lever may not be moved from the
P (Park) position even with the brake pedal
depressed and the shif t lever button
pressed. To move the shif t lever, perform
the following procedure:1. Place the ignition switch in the OFF or LOCK position.
2. Apply the parking brake.
3. Remove the shif t lock release cover us- ing a suitable tool. 4. Push down the shif t lock release using
a suitable tool.
5. Press the shif t lever button and move the shif t lever to the N (Neutral) position
while holding down the shif t lock re-
lease. The vehicle may be moved to the
desired location. Replace the removed
shif t lock release cover af ter the opera-
tion. If the shif t lever cannot be moved
out of the P (Park) position, have the
Continuously Variable Transmission
system checked as soon as possible. It
is recommended that you visit a
NISSAN dealer for this service.WARNING
If the shif t lever cannot be moved from
the P (Park) position while the engine is
running and the brake pedal is de-
pressed, the stop lights may not work.
Malfunctioning stop lights could cause
an accident injuring yourself and others.
Accelerator downshif t
— in D (Drive) position —
For passing or hill climbing, depress the
accelerator pedal to the floor. This shif ts
the transmission down into a lower gear,
depending on the vehicle speed.
High fluid temperature protection
mode
This transmission has a high fluid tem-
perature protection mode. If the fluid tem-
perature becomes too high (for example,
when climbing steep grades in high tem-
peratures with heavy loads, such as when
towing a trailer), engine power and, under
some conditions, vehicle speed will be de-
creased automatically to reduce the
chance of transmission damage. Vehicle
speed can be controlled with the accelera-
tor pedal, but the engine and vehicle speed
may be limited.
Fail-safe
If the vehicle is driven under extreme
conditions, such as excessive wheel
spinning and subsequent hard braking,
the fail-safe system may be activated.
The Malfunction Indicator Light (MIL)
may come on to indicate the fail-safe
mode is activated. For additional infor-
mation, refer to “Malfunction Indicator
Light (MIL)” in the “Instruments and con-
trols” section of this manual. This will oc-
cur even if all electrical circuits are func-
tioning properly. In this case, place the
ignition switch in the OFF position and
wait for 10 seconds. Then push the
LSD2756
Starting and driving5-23

LITHIUM-ION (Li-ion) BATTERY AIR
VENT
CAUTION
∙Do not place objects over or into the air
vent. The Li-ion battery or DC/DC con-
verter may overheat and be damaged.
∙ Do not allow any liquid to get on or inthe air vent. It may cause a short cir-
cuit and damage the Li-ion battery or
DC/DC converter.
∙ Clean the air vent regularly to prevent the Li-ion battery or DC/DC converter
from overheating. Regularly clean the air vent with a dry cloth
to prevent the vent from being blocked.
AIR FRESHENERS
Most air fresheners use a solvent that
could affect the vehicle interior. If you use
an air freshener, take the following precau-
tions:
∙ Hanging-type air fresheners can cause permanent discoloration when they
contact vehicle interior surfaces. Place
the air freshener in a location that al-
lows it to hang free and not contact an
interior surface.
∙ Liquid-type air fresheners typically clip on the vents. These products can cause
immediate damage and discoloration
when spilled on interior surfaces.
Carefully read and follow the manufactur-
er’s instructions before using the air fresh-
eners.
POWER MOONROOF (if so
equipped)
The sunshade is made from a tricot mate-
rial.
CAUTION
To help prevent damaging the moon-
roof while cleaning:
∙ Do not rub the material with a cloth. Doing so can damage the surface of
the material or cause a stain to
spread.
∙ Never use benzine, thinner or any similar chemical to clean the sun-
shade. This may discolor the moon-
roof and damage the surface.
∙ Clean water based stains by patting the surface with a clean sof t cloth
dampened in warm water. Press a
clean dry cloth onto the surface to re-
move as much dampness as possible
and then let air dry.
∙ Clean oil based stains by patting the surface with a clean sof t cloth damp-
ened in warm water. Press a clean dry
cloth onto the surface to remove as
much dampness as possible and then
let air dry.
LHV2057
Appearance and care7-5