2019 MITSUBISHI OUTLANDER low beam

Outside (Front) 1-7 Overview
1
N00100602838
Outside (Front)
Sunroof (if so equipped) P.5-51
Windshield wipers P.5-221
Engine hood P.9-3
Front fog lights (if so equipped) P.5-220, 9-33, 9-38
Outside rearview mirrors P.5-60 Side turn-signal lights (if so equipped) P.5-219, 9-33, 9-38 Side-view camera (if so equipped) P.5-146 Fuel tank filler P.3-3
Power window P.5-48
Front turn-s
ignal lights
P.5-219, 9-33, 9-37
Front turn signal lights P.5-219, 9-33, 9-37
Headlights, low beam P.5-209, 9-33, 9-35 Parking lights P.5-209, 9-33, 9-37 Daytime running lights P.5-209, 9-33, 9-37
Headlights, low beam P.5-209, 9-33, 9-35
Parking lights P.5-209, 9-33, 9-37 Daytime running lights P.5-209, 9-33, 9-37
Headlights, high beam P.5-209, 9-33, 9-36
Headlights, high beam P.5-209, 9-33, 9-36
Halogen headlights type LED headlights type
Front side-marker lights P.5-209, 9-33, 9-36
Front side-marker lights P.5-209, 9-33, 9-36
Sensor (if so equipped) [for Fo
rward Collision Mitigation System
(FCM), Lane Departure Warning System (LDW) and Automatic high beam system] P. 5-117, 5-136, 5-213 Rain sensor (if so equipped) P.5-221 Front-view camera (if so equipped) P.5-146BK0264300US.book 7 ページ ２０１８年２月２８日　水曜日　午後５時１６分

Forward Collision Mitigation System (FCM) (if so equipped) 5-124 Features and controls
5
If the FCM detects a malfunction in the sys- tem, either of the following messages will appear, the indicator will appear on the information screen of the multi-information display and the FCM will automatically be turned off.If the message remains even after the opera- tion mode is put in “OFF” and then turned back to “ON”, please contact your authorizedMitsubishi Motors dealer.
N00593400094
The sensor (A) is located inside the wind- shield as shown in the illustration. The sensor is shared in the following sys-tems:  FCM  Lane Departure Warning (LDW)  Automatic high beam system
NOTE
If the sensor or its surrounding area becomes extremely high temperature when parkingthe vehicle under a blazing sun, the “FCMSERVICE REQUIRED” message may appear. After the temperature of the sensor or its sur-rounding area has been in range, if the mes- sage remains even afte
r restarting the engine,
please contact an au
thorized Mitsubishi
Motors dealer.
Handling of the sensor

CAUTION To maintain proper performance of the FCM, LDW and Automatic high beam system;• Always keep clea
n the windshield.
If the inside of the windshield where the sensor is installed be
comes dirty or fogged,
contact an authorized Mitsubishi Motors dealer.• Do not apply an impact or load on the sen-sor or its surrounding area.
BK0264300US.book 124 ページ ２０１８年２月２８日　水曜日　午後５時１６分

Indicator light, warning light, and information screen display list (multi information display - Type 1)
Features and controls 5-183
5
N00557701074 N00557801349
Indicator light, warning light, and information
screen display list (multi information display -
Type 1) Indicator and warning light list 1- Position indicator
 P.5-204
2- Front fog light indicator (if so
equipped)
 P.5-204
3- Turn signal indicators/hazard warning
lights
 P.5-204
4- High beam indicator
 P.5-204
5- Charging system warning light
 P.5-206
6- Blind Spot Warning (BSW) indicator
light (if so equipped)
 P.5-126
7- Automatic high beam system indicator
(if so equipped)
 P.5-213
8- LED headlight warning light (if so
equipped)
 P.5-212
9- Active stability control (ASC) indicator
 P.5-100
10- Active stability
control (ASC) OFF
indicator
 P.5-100
11- Anti-lock braking
system warning light
 P.5-97
12- Supplemental Restra
int System (SRS)
warning light
 P. 4 - 4 1
13- Engine malfuncti
on indicator (“SER-
VICE ENGINE SOON” or “Check engine light”)
 P.5-206
14- Electric parking
brake warning light
(yellow) (if so equipped)
 P.5-205
BK0264300US.book 183 ページ ２０１８年２月２８日　水曜日　午後５時１６分

Indicator light, warning light, and information screen display list (multi information display - Type 1) 5-198 Features and controls
5
 The Forward Collision Mi
tigation System (FCM),
Lane Departure Warning system (LDW) and auto-matic high beam system is
temporarily unavailable
due to the high or low temperature of the sensor.
 After the temperature of the sensor has been in range, the system will automatically return to opera-tion. Refer to “Forward Coll
ision Mitigation System
(FCM): When a problem is detected” on page 5-122.Refer to “Lane Departure Warning System (LDW): System problem warning” on page 5-138. Refer to “Automatic high
beam system: System
problem warning” on page 5-216.
 The sensor is temporarily
unavailable due to condi-
tions such as the adhesion of contaminants to the sensor or windshield. This is not a malfunction.
Refer to “Lane Departure Wa
rning System (LDW): Sys-
tem problem warning”
on page 5-138.
Refer to “Automatic high be
am system: System problem
warning” on page 5-216.
 There is a fault in the system of automatic high beam.
 Contact an authorized Mitsubishi Motors dealer. Refer to “Automatic high
beam system: System
problem warning” on page 5-216.
Screen
Cause
Do this (Reference)
BK0264300US.book 198 ページ ２０１８年２月２８日　水曜日　午後５時１６分

Indicator and warning light package (multi information display - Type 2)
Features and controls 5-203
5
N00519801921
Indicator and warning light package (mu
lti information display - Type 2)
1- Washer fluid level warning light
 P.5-208
2- Position indicator
 P. 5-204
3- Front fog light indicator (if so
equipped)
 P. 5-204
4- Turn signal indicators/hazard warning
lights
 P. 5-204
5- Cruise control indicator
 P. 5-102
6- Door-ajar warning light
 P. 5-207
7- For details, refer to “Steering wheel
lock” on page 5-23. (if so equipped)
8- For details, refer to “Warning activa-
tion” on page 5-20. (if so equipped)
9- Electric power steering system warning
light
 P.5-98
10- 4WD ECO mode indicator (if so
equipped)
 P.5-83
11- 4WD LOCK mode indicator (if so
equipped)
 P.5-83
12- LED headlight warning light (if so
equipped)
 P.5-212
13- High beam indicator
 P. 5-204
14- ECO mode indicator
 P.5-220
15- ECO Drive Assist
 P. 5-204
16- Oil pressure warning light
 P. 5-207
17- Charging system warning light
 P. 5-206
18- High coolant temperature warning light
(red)
 P. 5-207
19- Low coolant temp
erature indicator
(blue)
 P. 5-204
20- Active stability control (ASC) indicator
 P. 5-100
21- Active stability control (ASC) OFF
indicator
 P. 5-100
22- Anti-lock braking system warning light
 P. 5-97
23- Supplemental Restra
int System (SRS)
warning light
 P. 4 - 4 1
BK0264300US.book 203 ページ ２０１８年２月２８日　水曜日　午後５時１６分

Indicators 5-204 Features and controls
5
N00519900127 N00520000216
The arrows will flash in time with the corre- sponding exterior turn signals when the turnsignal lever is used. Both arrows will flash
when the hazard warn-
ing flasher swit
ch is pressed.
N00520100086
A blue light comes on when the headlights are on high beam.
N00520200175
This indicator comes on while the front foglights are on.
N00551301078
This indicator light illuminates while theparking lights are on.
N00575601020
This indicator comes on in blue while thecoolant temperature is low.
N00579200030
This function displays
how fuel-efficiently
you are driving under different driving condi- tions. The ECO drive assist di
splay will change as
follows if you do fuel-efficient driving using the accelerator in a way well matched with the vehicle speed.
24- Engine malfuncti
on indicator (“SER-
VICE ENGINE SOON” or “Check engine light”)
 P. 5-206
25- Seat belt remi
nder/warning light
 P. 4-23
26- Tire pressure moni
toring system warn-
ing light
 P. 5-140
27- Brake warning light (red)
 P. 5-205
28- Multi information display
 P. 5-175
Indicators Turn signal indicators/Hazard warning lights
NOTE
 If the indicator flashes faster than usual or if the indicator stays on wi
thout flashing, check
for a malfunctioning turn signal light bulb or turn signal connection.
High beam indicator Front fog light indicator
(if so
equipped)Position indicator Low coolant temperature indi- cator - blue (Vehicle equipped with the multi information dis- play - Type 2)
NOTE
 When the indicator go
es out, this should be
used as a rough indication of when the heat-ing starts working.
ECO Drive Assist (Vehicle equipped with the multi infor-mation display - Type 2)
ECO drive level Low High
BK0264300US.book 204 ページ ２０１８年２月２８日　水曜日　午後５時１６分

Combination headlights and dimmer switch 5-212 Features and controls
5
[For vehicles equipped
with the F.A.S.T.-
key]The operation mode is changed to OFF or ACC and the driver’s door is not opened.
If the combination headlights and dimmer switch is turned to the “ ” or “ ” posi- tion again after the engine is turned off, the approximately 3-minute
auto-cutout function
described above will not
work. The lights (the
parking lights, tail li
ghts and license plate
lights) will stay on and will not turn off auto-matically.
N00584500028
This warning light will illuminate when thereis a malfunction in the LED headlights.
N00549801236
[When using a key to start the engine] If the driver’s door is opened with the key in the “OFF” or “LOCK” or “ACC” position orremoved from the ignition switch while the lights are on, the tone
will sound to remind
you to turn off the lights. [When using the F.A.S.T.-key to start the engine] If the driver’s door is opened with the opera-tion mode is put in OFF or ACC, or if the operation mode is changed to OFF while the lights are on, the tone
will sound to remind
you to turn off the lights. In either case, the lights will turn off automat- ically and so will the tone. Or you can turn the light switch to the “OFF” position to stopthe tone.
N00549901178
To change the headlights from high beam to low beam and vice vers
a, pull the turn signal
lever to (1). Switch the headlights to lowbeam as a courtesy whenever there are oncoming vehicles, or when there is traffic moving ahead of you. An illuminated blue
NOTE
 The light auto-cutout
function can be deacti-
vated. See your authorized Mitsubishi Motorsdealer for details. For vehicles equipped with the Smartphone Link Display Audio, adjustments can bemade using screen ope
rations. For further
details, refer to the se
parate owner’s manual.
When you want to keep the lights on:
LED headlight warning light
(if
so equipped)
NOTE
 If the warning light il
luminates, there may be
a malfunction in the unit. Contact an autho- rized Mitsubishi Motors dealer or a repairfacility of your choice to have the system checked.Type 1 Type 2
Headlight reminder buzzer Dimmer (high/low beam change)
BK0264300US.book 212 ページ ２０１８年２月２８日　水曜日　午後５時１６分

Combination headlights and dimmer switch
Features and controls 5-213
5
light in the instrument
cluster i
ndicates when
the headlights are on high beam.
N00550001209
You can flash the high beams by pulling the lever gently toward you (2). The lights will go back to normal when you let go. While thehigh beam is on, you will see a blue light on the instrument panel.
N00591300028
The automatic high beam
system turns the
high beam light on or
off automatically
according to surrounding light conditions. The sensor (A) detects lights, such as thelights of an oncoming
vehicle, a vehicle
ahead or street lights.
N00593600070
1. Rotate the light switch to “ ” position or “AUTO” position when the engine isrunning. 2. Press the automatic high beam system switch.The automatic high beam system is acti- vated and the indicator is illuminated. If the automatic high beam system switchis pressed again, the automatic high beam system will be deac
tivated and automatic
high beam system indicator will go off.
Headlight flasher
NOTE
 You can flash the high beams by pulling the lever toward you, even if the light switch isoff.
 If you turn the lights off with the head lights set to high-beam illumin
ation, the headlights
are automatically returned to their low-beamsetting when the light
switch is next turned
to the “ ” position.
Automatic high beam system
(if
so equipped)
NOTE
WA R N I N G Do not rely solely on the Automatic High Beam. Always observe surrounding trafficand light conditions. If necessary, manu-ally turn the high beams on or off. Refer to “Dimmer (high/low beam change)” on page 5-212.
How to use the automatic high beam system

BK0264300US.book 213 ページ ２０１８年２月２８日　水曜日　午後５時１６分