Replacement of light bulbs 9-30 Vehicle care and maintenance
9
2. Remove the bulb from the socket by turn- ing it counterclockwise while pressing in. 3. To install the bulb, perform the removal steps in reverse.
N00943601904
1. Insert a straight
blade (or minus) screw-
driver with a cloth over its tip at the edge of the cover (A) and pry gently to remove the cover.
2. Remove the 3 screws (B) and remove the light unit.
3. Depress the tab (D) on the harness con- nector and pull the harness connector (E)to remove it. 4. Turn the bulb (F) counterclockwise to remove it. 5. To install the bulb, perform the removal steps in reverse.
Front fog lights
(if so equipped)
NOTE
When unfastening the screw of the fog light, be careful not to mistakenly move the beam position adjustment screw (C).
BK0267800US.book 30 ページ ２０１８年５月３０日 水曜日 午後４時２４分
Replacement of light bulbs
Vehicle care and maintenance 9-31
9
N00943701572
1. Open the trunk lid. 2. Remove the screws (A) that hold the light unit. 3. Move the light unit toward the rear of the vehicle to unfix the notch (B) and pin (C).
4. Turn the socket counterclockwise to remove it. 5. Remove the bulb from the socket as fol- lows. • Type 1: Rear side-marker light bulb
Pull the bulb out.
• Type 2: Other light bulb
Turn the bulb counterclockwise while pressing in.
6. To install the bulb, perform the removal steps in reverse.
Rear combination lights
D- Back-up lightE- Rear turn signal lightF- Tail and stop light G- Rear side-marker light
NOTE
When mounting the light unit, align the notch (H) and pin (I) on the light unit withthe clip (J) and hole (K) in the body.Type 1 Type 2
BK0267800US.book 31 ページ ２０１８年５月３０日 水曜日 午後４時２４分
Vehicle care precautions 9-32 Vehicle care and maintenance
9
N00944001439
1. Turn the socket counterclockwise to remove it, and then pull the bulb out of the socket. 2. To install the bulb, perform the removal steps in reverse.
N00945100166
In order to maintain the value of your vehicle, perform regular mainte
nance using the proper
materials and procedures. Be sure to use onlythose materials and proc
edures that meet your
local environmental pollution control regula- tions. Choose the materials you will use care-fully, to be sure that they do not contain corrosives. If you are
not sure, contact an
authorized Mitsubishi Motors dealer for help in choosing these materials.
These can all be dangerous, and they all can damage your vehicle.
N00945200095
After washing the inside of your vehicle withany cleaner, wipe it dry in a shady, well venti- lated area.
License plate lights
Vehicle care precautions
CAUTION Cleaning products can be dangerous. Some are poisonous and others
are highly flamma-
ble. Some are dangerous if you breathe their fumes in a closed sp
ace. When you use any-
thing in a container to
clean your vehicle, be
sure to follow the in
structions. Always open
your vehicle doors or windows when you’re cleaning the inside. Never use the followingchemicals to clean your vehicle:• Gasoline• Carbon Tetrachloride• Benzine• Kerosene• Naphtha• Acetone• Turpentine• Paint Thinner• Lacquer Thinner
• Nail Polish Remover
Cleaning the inside of your vehicle
CAUTION Do not use organic substances (solvents, benzine, kerosene, alc
ohol, gasoline, etc.) or
alkaline or acidic solutions.These chemicals can cause discoloring, staining or cracking of the surface. If you use cleaners or polishing agents, makesure their ingredients do not include the sub- stances mentioned above.NOTE
Always read the instru
ctions on the cleaner
label.CAUTION
BK0267800US.book 32 ページ ２０１８年５月３０日 水曜日 午後４時２４分
